Furniture Solutions 17ONY08B User manual

Imported by Furniture Solutions (Aust) Pty Ltd New South Wales, Australia.
For any assistance with assembly or for missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone-1300 794 188
Email- [e-mail]
INSTRUCTION MANUAL
ONYX SQUARE 150CM DINING TABLE
ITEM CODE: 17ONY08B
117ONY08B

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
217ONY08B
30
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2

COMPONENT & HARDWARE LIST
PART CODE
1
TABLE TOP x 1 P.73200.TT
2
TABLE BASE x 1 P.73200.TB
3
Steel Plate x 2 P.73200.SP
317ONY08B

FIT Steel Plates
Prepare product as per page 2:
Ensure base is upright with holes facing up, lay steel plate (3) over holes with rebated hole facing
up, and ensure all 5 holes are visible. Insert bolt (A) thru steel plate (3) from top of base. At
threaded end of bolt (A) place washer (C), then take long nut (B) and by hand turn 2-3 times to
seat thread correctly at this point do not tighten, Repeat for all other bolts as per diagram 10 in
total. Once all bolts are seat correctly tighten using Allen keys (D) provided. Note do not
overtighten just till firm. Move to Step 2.
417ONY08B

STEP
2: FIT TABLE TOP TO BASE
Please note this is a very heavy item and will require 2 reasonably strong people to pick up and
place into position.
With the help of another person or two remove top from carton. Ensure holes in bottom of table
top (1) are facing towards the ground. With help of another person pick table up by the long edge
1 person each side, centre to balance top on base as per diagram, once top (1) is stable, from
under table line up holes between steel plates (3) and table top, move slowly as to not upset
balance. Once lined up take Bolt (A) & Washer (C) insert into hole and by hand seat thread
properly, turn 2-3 times, at this point do not tighten, Repeat for all other bolts as per diagram 8 in
total. Once all bolts are seated correctly tighten using Allen keys (D) provided. Note do not
overtighten just till firm. Assembly Complete
Warning never drag table always lift FROM THE SIDE WITH STEEL PLATES and with the help of
another person. Dragging can cause damage to product and or your floor surface.
517ONY08B
Reverse Close up view

617ONY08B
CARE AND MAINTENANCE
Varieties of materials are used in construction of “Outdoor” furniture ranges.
All will require some form of maintenance to extend the life of finishes and general appearance.
Please see below instruction unique to your chosen product.
Onyx Dining Range Construction;
Poly + sand + stone powder mixed and poured into a matrix or moulding frame, this produces a
panel of required size of 5mm thickness. Then a layer of fiberglass is applied to back of panel to
add strength and rigidity and during the assembly process a further support system is added a
steel frame to avoid flex. Once this is added another panel is added to seal all panels into a box.
Finishing is apply to surface sanding and a final coat of clear paint is sprayed on.
Care Instruction;
Please keep dust free, avoid leaving vegetation on surface as leaves and sap can leave stains
that can not be removed. Avoid leaving spills on surface as orange juice & alcohol are acidic and
will damage surface coating if left unattended for any length of time.
Regular cleaning please use a soft bristle dust pan brush or a soft clean cloth, using a hose is
permissible but not at high pressure, please pat dry as the trace minerals in water may leave a
mark once water has evaporated (Do Not Use Bore Water).
Included in packaging is a small can of wax, note this is for cleaning of grime build up.
Using a soft clean cloth you apply the wax in a circular motion to affected area, with this action
the wax then picks up the grime and retains the grime within its self, then with a soft clean coth
remove the wax taking the grime with it. Repeat if necessary. Note may not clean up all
especially any dye based grime and or chemicals.
Definition of Regular Cleaning;
Numerus factors can influence the time frame for cleaning, depending area you live in, the
weather, positioning of the product (fully protected, partial protection, fully exposed to the
elements). You will need to monitor yourself to establish the cleaning requirement for your
unique situation.
Areas with high salt content and or pollution will require the most frequent cleaning.
To reduce some maintenance you should buy and use an outdoor cover to protect your
furniture from the elements when not in use.
.

717ONY08B
SAFETY WARNINGS AND ADVICE
Notices and Advice
Please be advised that products are limited in design for residential use only and are not
suitable for commercial use.
Please be advised that materials used in your furniture are not impervious to neglect, acts of
god, abuse, alcohol spills, improper use of chemicals such as bleach or any solvent based
products.
Please be advised that heat sources such as barbeques, open fires,
temporary/mobile/overhead heaters, poorly insulated candle holders, hot pots, pans, hot
serving dishes can have adverse affects on your furniture.
Please be advised that fitting, bolts, nuts and or screws should be checked periodically to
ensure they have not loosened over time. Remember do not overtighten.
Please be advised coverings are not animal proof. Claws can scratch covering & saliva is
acidic and can damage finish.
DO NOT
•Place in close proximity to open flame or heaters.
•Leave spills or food, clean off immediately
•Pull loose thread, cut them instead.
•Sit or lean on arms
•Stand on chair or bench's
•Stand on table tops
•Place heavy objects on table tops
•Place objects such as pot plants as a display piece on tables recommend weight
restriction for table top is 60kg across the table.
Safety warnings
•DO NOT:
•drop, drag always move furniture with the help of another person lift and place only
•Over load bench seats recommended weight evenly distributed is 360kg IE: 3 people
120kg each; 4 people 90kg each.
•Tables, chairs & bench's are designed for seating, not work bench's.
•Allow child to play under table

817ONY08B
Warranty Detail:
1 Year Warranty
A one (1) year warranty applies to product against any defect associated with faulty
workmanship for a period of (1) year from date of purchase.
Furniture Solutions accepts no responsibility for defects caused by incorrect assembly,
mishandling, acts of god, general wear & tear, stains from spills/vegetation, chipping/scratching,
exposure to extreme heat/cold, mould/mildew, hardware corrosion, misuse of the products &
defects caused by failure in duty of care for the product in accordance with the care instructions.
Warranty only extends to original purchaser and is not transferable, except when given as a gift.
Goods are limited in design for domestic use only, and are not suitable for commercial use.
Duty of care:
While every attempt is made to supply product using quality components there is always a need
from consumer to help ensure a long life of use for product.
*Proper use of item, only what it is designed to do. Designed for dining, not suitable for use as a
workbench, substitute ladder or dance floor.
*Regular maintenance and cleaning: Please consult your Instruction manual included in packaging
for advice of cleaning
*Protecting product from the harsh environment: Pollution, excessive moisture & heat.
To extend the life of your outdoor furniture we recommend the following furniture covers
must/should be used on furniture which is used in areas not protected from elements.
Caution should be used when using oils, lotions & other chemicals such as chlorine not to spill on
furniture.
Instruction Manual –Have been written to suit individual materials used in construction, please
retain for future use for duty of care, assembly, parts & component sizing.
Claim management:
To make a warranty claim, customers can either contact the retailer where the purchase was
made or Furniture Solutions on contact details below. Proof of purchase will be required before
proceeding with any claim. In the case of product defects providing photos may be able to speed
up processing of the claim. If missing parts please refer to assembly instructions for identification
of said part and contact either of the above.
“Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure”.