Furuno MU-152HD User manual

www.furuno.com
OPERATOR'S MANUAL
15型カラーLCD表示器
取扱説明書
Marine Display
Model MU-152HD

・
本書の無断複写複製(コピー)は特定の
場合を除き、当社権利侵害になります。
( TEHI ) MU-152HD
Pub. No. OMC-45200-A1
Printed in Japan
・ 機器の修理・使用方法等に関するお問い合わせは、お買い上げの販売店・代理店、最寄りの
当社支店・営業所あてへお願いします。
FURUNO Authorized Distributor/Dealer お問い合わせは
: JAN. 2023
:MAR. 17, 2023
A
A1
00019975310

i
IMPORTANT NOTICES
General
• This manual has been authored with simplified grammar, to meet the needs of international users.
• The operator of this equipment must read and follow the instructions in this manual.
Wrong operation or maintenance can void the warranty or cause injury.
• Do not copy any part of this manual without written permission from FURUNO.
• If this manual is lost or worn, contact your dealer about replacement.
• The contents of this manual and the equipment specifications can change without notice.
• The example screens (or illustrations) shown in this manual can be different from the screens you
see on your display. The screens you see depend on your system configuration and equipment
settings.
• Save this manual for future reference.
• Any modification of the equipment (including software) by persons not authorized by FURUNO will
void the warranty.
• The following concern acts as our importer in Europe, as defined in DECISION No 768/2008/EC.
- Name: FURUNO EUROPE B.V.
- Address: Siriusstraat 86, 5015 BT, Tilburg, The Netherlands
• The following concern acts as our importer in UK, as defined in SI 2016/1025 as amended SI 2019/
470.
- Name: FURUNO (UK) LTD.
- Address: West Building Penner Road Havant Hampshire PO9 1QY, U.K.
• All brand, product names, trademarks, registered trademarks, and service marks belong to their
respective holders.
How to discard this product
Discard this product according to local regulations for the disposal of industrial waste. For disposal in
the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the
correct method of disposal.
How to discard a used battery
Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter
on Maintenance. If a battery is used, tape the + and - terminals of the battery before disposal to pre-
vent fire, heat generation caused by short circuit.
In the European Union
The crossed-out trash can symbol indicates that all types of batteries
must not be discarded in standard trash, or at a trash site. Take the
used batteries to a battery collection site according to your national
legislation and the Batteries Directive 2006/66/EU.
In the USA
The Mobius loop symbol (three chasing arrows) indicates that
Ni-Cd and lead-acid rechargeable batteries must be recycled.
Take the used batteries to a battery collection site according to
local laws.
In the other countries
There are no international standards for the battery recycle symbol. The number of symbols can in-
crease when the other countries make their own recycle symbols in the future.
Cd
Ni-Cd Pb

ii
SAFETY INSTRUCTIONS
Indicates a condition that can cause death or serious
injury if not avoided.
Indicates a condition that can cause minor or moderate
injury if not avoided.
CAUTIONCAUTION
Read these safety instructions before you operate the equipment.
WARNING
CAUTION
Warning, Caution Prohibitive Action Mandatory Action
Safety Instructions for the Operator
WARNING WARNING
Immediately turn off the power at the
switchboard if water leaks into the
equipment or something is dropped
into the equipment.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury
can result.
Turn off the power immediately
if you feel the equipment is behaving
abnormally.
Turn off the power at the switchboard if
the equipment becomes abnormally warm
or is emitting odd noises. Contact a
FURUNO dealer or agent for advice.
Use the proper fuse.
Fuse rating is shown on the power
cable. Use of a wrong fuse can result
in damage to the equipment.
Do not place any object near the
exhaust or intake vent.
Fire may result.
Do not connect/disconnect the
signal cable while turning the power
on.
The unit may be damaged.
Handle the LCD monitor with care.
The face of the LCD monitor is made of
glass. Injury may result if the glass
breaks.

SAFETY INSTRUCTIONS
iii
Safety Instructions for the Installer
WARNINGWARNING CAUTIONCAUTION
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Do not install the equipment where it
may get wet from rain or water
splash.
Water in the equipment can result in fire,
electrical shock or damage to the
equipment.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
Standard
compass
Steering
compass
MU-152HD
0.60 m 0.35 m
When lifting the display unit, hold it
together with the hard cover.
Grasping by the hard cover alone may
allow the display unit to fall, resulting in
possible bodily injury or damage to the
equipment.
The TFT LCD is constructed using the latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.01% of the pixels may drop out or
blink, however this is not an indication of malfunction.
About the TFT LCD
About the TFT LCD

iv
TABLE OF CONTENTS
FOREWORD ....................................................................................................................v
SYSTEM CONFIGURATION ..........................................................................................vi
EQUIPMENT LISTS.......................................................................................................vii
1. MOUNTING, WIRING................................................................................................1
1.1 Preparation.................................................................................................................... 1
1.2 Flush Mounting, Fixed at Rear ...................................................................................... 3
1.3 Flush Mounting, Fixed at Front ..................................................................................... 7
1.4 Flush Mounting, Fixed at Rear, with Hood .................................................................. 10
1.5 Desktop Mounting ....................................................................................................... 13
1.6 Flush Mounting a Series Side by Side ........................................................................ 15
1.7 Wiring .......................................................................................................................... 16
2. ADJUSTMENTS......................................................................................................18
2.1 RGB/DVI/HDMI Setting ............................................................................................... 18
2.2 Video Composite Signal Setting.................................................................................. 20
2.3 The Menu Window Setting .......................................................................................... 21
2.3.1 How to adjust the menu window.......................................................................... 21
2.3.2 How to change the signal name .......................................................................... 22
3. OPERATION ...........................................................................................................23
3.1 Controls....................................................................................................................... 23
3.2 How to Turn the Power On/Off.................................................................................... 24
3.2.1 Turn on/off the power........................................................................................... 24
3.2.2 Lock the operation ............................................................................................... 24
3.3 How to Adjust the Display Brilliance............................................................................ 24
3.4 How to Select the Source for Main Picture ................................................................. 25
3.5 How to Select the Source for the PIP Window............................................................ 25
3.6 SYSTEM Menu ........................................................................................................... 26
3.6.1 How to adjust the brilliance from the external equipment .................................... 26
3.6.2 FISH FINDER Mode ............................................................................................ 26
3.6.3 How to clear the memory..................................................................................... 27
4. MAINTENANCE, TROUBLESHOOTING................................................................28
4.1 Maintenance................................................................................................................ 28
4.2 Troubleshooting .......................................................................................................... 29
APPX. 1 ABBREVIATIONS......................................................................................AP-1
SPECIFICATIONS .....................................................................................................SP-1
INSTALLATION MATERIALS ..................................................................................... A-1
OUTLINE DRAWINGS................................................................................................. D-1
INTERCONNECTION DIAGRAMS .............................................................................. S-1

v
FOREWORD
A Word to the Owner of the MU-152HD
FURUNO Electric Company thanks you for purchasing the MU-152HD 15” Marine Display. We are
confident you will discover why the FURUNO name has become synonymous with quality and re-
liability.
Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for quality and reli-
ability throughout the world. This dedication to excellence is furthered by our extensive global net-
work of agents and dealers.
Your equipment is designed and constructed to meet the rigorous demands of the marine envi-
ronment. However, no machine can perform its intended function unless properly installed and
maintained. Please carefully read and follow the operation, installation and maintenance proce-
dures set forth in this manual.
We would appreciate feedback from you, the end-user, about whether we are achieving our pur-
poses.
Thank you for considering and purchasing FURUNO.
Features
The main features of the MU-152HD are as shown below.
• Selectable screen from RGB (1 line), DVI-D (1 line), HDMI (1 line) or Composite (1 line).
• Main or remote display for radars, video sounders, sonars, plotter. For the connectable equip-
ments, see "Connectable equipment" on page vi.
• High resolution display of 1024 x 768 (XGA)
• Brightness of 1000 cd/m2(maximum) and 0.3 cd/m2or less (minimum) for comfortable viewing
day and night.
• Picture-in-picture function
• Power on/off automatically through the DVI/HDMI signal.
Program Number
xx: minor change
CE/UKCA declaration
With regards to CE/UKCA declarations, please refer to our website (www.furuno.com), for further
information on RoHS conformity declarations.
Program Name Version Date of Modification
Main 1.xx Jan. 2023

vi
SYSTEM CONFIGURATION
Connectable equipment
Note 1: This equipment is used as a display for a Non-SOLAS radar or ECDIS.
Note 2: Landscape orientation only.
Note 3: When inputting SXGA, a circle may be displayed as an ellipse because the aspect ratio
differs. See "DISP MODE*" on page 19. Also, it may be difficult to read small characters.
Equipment Resolution Signal
CSH-5L/8LMK2 XGA RGB
CH-500/600 XGA HDMI
FCV-38 XGA/SXGA HDMI
FCV-2100 XGA/SXGA DVI
FCV-1900 XGA/SXGA DVI
CI-38/68/88 BB VGA RGB
GD-300 XGA DVI
GD-700 XGA/SXGA DVI
FAR-14x7 XGA/SXGA DVI
FAR-15X3/15X8 XGA DVI
FAR-2xx8 SXGA DVI
FSV-25/25S MARK-2 SXGA DVI
FSV-75 SXGA HDMI
CSH-5LMK2/8LMK2, etc.
FAR-15x8, GD-300,
FCV-1900,㻌etc.
CCD camera,
DVD recorder, etc.
RGB
DVI-D
VIDEO (NTSC/PAL)
12-24 VDC
MARINE DISPLAY
MU-152HD
Environmental category
MU-152HD: Protected from the weather
HDMI FCV-38, CH-500/600, etc.
USB FAR-1417/1427
Processor Unit

vii
EQUIPMENT LISTS
Standard supply
Optional supply
Name Type Code No. Qty Remarks
Marine Display MU-152HD-A – 1 w/ Hard cover
Spare Parts SP26-01001 001-621-760 1 set
Cable Assy. MJ-A3SPF0017A-
050ZC
000-175-421-10 1
Flush Mount Fixture
15
CP26-02601 001-621-770 1 set
Installation Materials CP26-02602 001-621-780 1 set
Name Type Code No. Qty Remarks
Cable Assembly
3COX-2P-6C 5M 001-077-230-10 1 Cable length: 5 m (15 pin D-sub
connector at both ends)
3COX-2P-6C 10M 001-077-220-10 1 Cable length: 10 m (15 pin D-
sub connector at both ends)
DVI-D/D S-LINK
5M
001-132-960-10 1 Cable length: 5 m
(with DVI-D connector at both
ends)
DVI-D/D S-LINK
10M
001-133-980-10 1 Cable length: 10 m
(with DVI-D connector at both
ends)
Bracket Assembly JE07002-B003 001-634-610 1 set
Hood Assembly JE07002-B005 001-634-630 1 set
Front Fixed Flush
Mount Kit
JE07002-B022 001-634-650 1 set
LCD Retrofit Kit JE07002-B020 001-634-670 1 set
Rear Fixed Flush
Mount Kit
JE07002-B024 001-641-210 1 set

1
1. MOUNTING, WIRING
1.1 Preparation
Mounting type
The display unit can be installed in the following methods. See the outline drawing at the back of
this manual for mounting dimensions.
• Flush mounting, fixed at rear (standard)
• Flush mounting, fixed at front (option)
• Flush mounting, fixed at rear, with hood (option)
• Desktop mounting (option)
• Flush mounting a series side by side, fixed at rear
Note: The face of the LCD monitor is made of glass. Handle it with care.
Mounting location
When selecting a mounting location, remember the following points:
• Make sure the mounting location is strong enough to support the weight of the unit.
• Locate the unit away from direct sunlight. An LCD may black out if it is exposed to direct sunlight
for a long time.
• Select a location where the display can be easily viewed and the controls can be easily operat-
ed.
• Leave enough space around the unit for service and maintenance. See the outline drawing at
the back of this manual for minimum service clearance.
• Locate the unit away from areas subject to water splash and rain.
• Observe the compass safe distances (see page iii) to prevent interference to a magnetic com-
pass.
How to remove/attach the hard cover
Before you install this display unit, remove the hard cover as follows.
Grasping by the hard cover alone may
allow the display unit to fall, resulting in
possible bodily injury or damage to the
equipment.
When lifting the display unit, hold it
together with the hard cover.
CAUTION

1. MOUNTING, WIRING
2
How to remove the hard cover
To attach the hard cover, follow the illustration in the figure below.
How to attach the hard cover
Cable connecting
Before you install the display unit, connect all the cables. See the interconnection diagram at the
back of this manual.
The upper edge of the hard cover
Pull the upper edge
forward by pressing here
with thumbs.
Hard cover
Tab
CutoutCutout
Set the tabs on the top
of the hard cover to the
cutouts on the display
unit.
Push the tabs of the
bottom of the hard cover
strongly (2 places).

1. MOUNTING, WIRING
3
1.2 Flush Mounting, Fixed at Rear
This is the standard installation method.
Flush Mount Fixture 15 CP26-02601 (code no. 001-621-770)
Installation Materials CP26-02602 (code no. 001-621-780)
1. Make a cutout in the mounting location with the “Flush mounting template” (included).
Name Type Code No. Qty Remarks
IM List JE07002-Y533 000-199-746-10 1
Mount metal 15 JE07002-Y528 000-199-988-10 2
Butterfly bolt JE82001-0013 000-199-986-10 6
Butterfly nut JE82001-0014 000-199-987-10 6
Protector for screw 26-005-2125-0 100-354-800-10 6
Washer head screw J6-SW3N4-
10200
000-199-677-10 12
Attachment 15 JE07002-Y527 000-199-683-10 2
Name Type Code No. Qty Remarks
IM List JE07002-Y946 000-199-747-10 1
Fmount sponge H15 JE07002-Y543 000-199-684-10 2
Fmount sponge V15 JE07002-Y544 000-199-685-10 2
364±1 (14.33”)
314±1 (12.36”)
4-ø18(0.71”)*
*: The drill bit with a diameter of 18 mm or less
can also be used.

1. MOUNTING, WIRING
4
2. Attach the flush mounting sponges H15 and V15 in the order shown in the figure below.
3. Connect all cables at the back of the display unit. See section 1.7.
4. Set the display unit to the cutout.
Fmount sponge H15 for
top and bottom
䐟
䐠
䐢
䐡
Fmount sponge V15
for right and left
Cutout

1. MOUNTING, WIRING
5
5. Attach the attachment 15 to the left and right sides of the back of the display unit with the sup-
plied washer head screws.
6. Screw the butterfly bolts and the butterfly nuts of the mount metal 15 so that the protector
moves to the mount metal.
Washer hear screws
(Three on each side)
Attachment 15
(One on each side)
Wing nut
Mount metal 15
Mount metal 15
Set to the metal.
Protector for
screw
Mounting Metal
Butterfly
Bolt
Butterfly
Nut
Wall thickness is 3 mm to 14 mm
Wall thickness is 14 mm to 25 mm
Butterfly
Nut
Butterfly
Bolt
Mount metal
Protector for
screw
Set to the mount metal.

1. MOUNTING, WIRING
6
7. Fasten the mount metal 15 to the right and left sides of the rear of the display unit with the
washer head screws (6 places).
8. Loosely fasten the butterfly bolts, in the order of the number shown in the figure below so that
the protectors touch the mounting panel.
9. Fasten the butterfly bolts tightly, in the order shown in step 7.
10. Fasten the butterfly nuts tightly.
Mount Metal 15
Washer Head Screw
䐠䐠
䐤䐤
䐢䐢
Butterfly bolt
Butterfly nut
Mount metal
Protector for screw
Attachment
Mount Panel

1. MOUNTING, WIRING
7
1.3 Flush Mounting, Fixed at Front
If there is not enough space to fix the display unit from the rear, you can fix it from the front with
the optional Front Fixed Flush Mount Kit JE07002-B022 (code no. 001-634-650). The LCD Retrofit
Kit JE07002-B020 (code no. 001-634-670) can also be used.
Front Fixed Flush Mount Kit JE07002-B022 (code no. 001-634-650)
LCD Retrofit Kit JE07002-B020 (code no. 001-634-670)
Fixing with Front Fixed Flush Mount Kit JE07002-B022
1. Make a cutout in the mounting location with the flush mounting template (included).
Name Type Code No. Qty Remarks
Fmount panel 15 assembly JE07002-Y533 000-199-706-10 1
Self tapping screw JE82001-0015 000-199-688-10 4
Washer head screw J6-SW3N4-
10200
000-199-677-10 8
Fmount sponge H15 JE07002-Y543 000-199-684-10 2
Fmount sponge V15 JE07002-Y544 000-199-685-10 2
Flush Mounting Template C42-00909-x 000-172-636-1x 1 x denotes minor
modifications.
Name Type Code No. Qty Remarks
Spacer JE07002-Y580 000-199-707-10 8
Self tapping screw JE82001-0015 000-199-688-10 4
Washer head screw J6-SW3N4-
10200
000-199-677-10 8
Fmount sponge H15 JE07002-Y543 000-199-684-10 2
Fmount sponge V15 JE07002-Y544 000-199-685-10 2
Flush Mounting Template C42-00909-x 000-172-636-1x 1 x denotes minor
modifications.
370 (14.57”)
320 (12.60”)
382±0.5 (15.04”)
332±0.5 (13.07”)
Pilot hole
for mounting from the front
4-ø18(0.71”)*
*: The drill bit with a diameter of 18 mm
or less can also be used.

1. MOUNTING, WIRING
8
2. Attach the flush mounting sponges H15 and V15 in the order shown in the figure below.
3. Attach the flush mounting panel (15) to the display unit from the rear with the washer head
screws (M410, 8 places, torque: 1.2 N•m). Do not confuse the top and bottom of the panel
and check that screw holes on the panel and unit match.
4. Connect all cables at the back of the display unit. See section 1.7.
5. Set the display unit assembly prepared at the section 3 to the cutout for the mounting location.
Fmount sponge H15 for
top and bottom
䐟
䐠
䐢
䐡
Fmount sponge V15
for right and left
Washer
Head
Screw
Narrow
Wide
Fmount panel 15
assembly

1. MOUNTING, WIRING
9
6. Fix the display unit to the cutout with the self tapping screws (4 places).
Fixing with LCD Retrofit Kit JE07002-B020
1. Attach the flush mounting sponges H15 and V15 in the order shown in the figure below.
Self tapping screw
Fmount sponge H15 for
top and bottom
䐟
䐠
䐢
䐡
Fmount sponge V15
for right and left

1. MOUNTING, WIRING
10
2. Attach the flush mounting panel (15) to the display unit from the rear with the spacers and
washer head screws (M410, 8 places, torque: 1.2 N•m). Do not confuse the top and bottom
of the panel and check that screw holes on the panel and unit match.
3. Connect all cables at the back of the display unit. See section 1.7.
4. Set the display unit assembly prepared at the step 3 to the cutout for the mounting location.
5. Fix the display unit to the cutout with the self tapping screws (4 places).
1.4 Flush Mounting, Fixed at Rear, with Hood
You can attach a hood when flush mounting the unit from the rear, using the hood assembly
JE07002-B005 (option).
Note: When the hood is installed, the hard cover cannot be used.
Hood Assembly JE07002-B005 (Code: 001-634-630)
Name Type Code No. Qty
Hood (15) Assembly JE07002-B006 001-080-950-00 1
F-Mount Hood Gasket 15 JE07002-Y563 000-199-701-10 1
Hood Gasket Bottom 15 JE07002-Y570 000-199-702-10 1
Narrow
Washer Head Screw
and spacer
Fmount panel 15 assembly
(Detach and reuse from
MU-150HD)
Wide
Self tapping screw

1. MOUNTING, WIRING
11
1. Make a cutout in the mounting location with the flush mounting template (included).
2. Attach the attachment 15 to the left and right sides of the back of the display unit with the sup-
plied washer head screws.
F-Mount Hood Gasket Side 15 JE07002-Y571 000-199-703-10 2
Hood Fixing Plate 15 JE07002-Y572 000-199-704-10 2
Knob M4 JE07002-Y562 000-199-692-10 4
Flat Head Screw J6-SSA3-06200 000-199-693-10 6
Flush Mounting Template C42-00908 000-172-635-10 1
Name Type Code No. Qty
368±1 (14.49”)
314±1 (12.36”)
4-ø18(0.71”)*
*: The drill bit with a diameter of 18 mm or
less can also be used.
Washer hear screws
(Three on each side)
Attachment 15
(One on each side)