FUTABA R6208SB User manual

Usage condition on "High Speed mode"
ｎCAUTION
ｊWhen using the high-speed mode, use a Futaba
digital servo (including brushless servo) or S.BUS
servo at conventional system use channels 1to 6.
Analog servos cannot be used.
s4HEUSEOFANALOGSERVOSMAYCAUSESERVOTROUBLE
s7HEN USING ANALOG SERVOS SELECT THE NORMAL MODE AND
use channel outputs 7 and 8.
Applicable systems: T8FG 2.4GHz (on 8ch mode), TM8 (on 8ch mode), T10CG 2.4GHz (on
10ch mode), TM10 (on 10ch mode), TM14 (on multi-ch mode)
R6208SB S.BUS compatible/FASST-2.4GHz (Multi-ch) system
8 channels/high-speed receiver
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model
number R6208SB, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL [phone] or E-mail: [email protected] (Support)
R6208SB Specifications
S.BUS compatible/FASST-2.4GHz (Multi-ch) system/8 channels/
high-speed receiver
• Dual antenna diversity
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
• Weight: 0.49 oz. (13.8g)
• Power requirement: 3.7V to 7.4V
(Voltage range: 3.5 to 8.4V)
*Be sure that when using ESC's regulated output the capacity of the ESC
must meet your usage condition.
*The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S
function doesn't work properly when other type battery is used.
Thank you for purchasing a Futaba R6208SB S.BUS
compatible receiver.
The R6208SB has an S.BUS system output port and a
conventional system channel output. It can also be used with
conventional system servos, etc. in addition to S.BUS system
compatible servos and gyros, etc.
In addition, the operating mode (high-speed mode/normal
mode) can be selected.
* However, channel outputs 7 and 8 for conventional system oper-
ate in the normal mode even if set to the high-speed mode.
Link/Mode switch
LED
R6208SB
DATA port s#HANNELOUTPUTSFORCONVENTIONAL
system (1to 8)
s"ATTERYTERMINALB)
sS.BUS Port (S.BUS)
What is S.BUS?
Different from conventional radio control systems the S.BUS
system uses data communication to transmit control signals
from a receiver to a servo, gyro, or other S.BUS compatible
device. This data includes commands such as “move the
channel 3 servo to 15 degrees, move the channel 5 servo to
30 degrees” to multiple devices. The S.BUS devices execute
only those commands for their own set channel. For this
reason, it can be used by connecting multiple servos to the
same signal line.
[Connection by S.BUS system]
S.BUS hub S.BUS hub
S.BUS output S.BUS
Ch output/
Battery terminal
R6208SB
Battery S.BUS servo
Conventional
servo
2ch 4ch
3ch 5ch
6ch
* Can also be used together with conventional servos.
* When using servos with a remote battery pack, use S.BUS Hub with Cable (2-way/remote battery pack use).
Please refer to the instruction manual of S.BUS Hub with Cable (2-way/remote battery pack use) for the connection method.

S.BUS Servo Channel Setting Method
S.BUS servo channel setting can be performed at the R6208SB
receiver.
1#ONNECTTHEACCESSORYSHORTPLUGTOTHEDATAPORTOF
the receiver.
Short-plug
(accessory)
* Connect the short-plug to the DATA port only when an S.BUS servo
channel is set. Normally do not connect the plug.
2#ONNECT AN S.BUS servo to the conventional system
output connector(1to 8) corresponding to the channel
you want to set.
Output
connector
#HANNELSETTING
Mode A -ODE"
11 9
22 10
33 11
44 12
55 13
66 14
77 15
88 16
* Channel setting mode A (ch1 to 8 setting mode) or channel setting
mode B (ch9 to 16 setting mode) can be set.
34URNONTHERECEIVER
* At once when turning on the receiver, the channel setting is com-
pleted in mode A.
4OSWITCHTOMODE"PRESSTHELink/Mode button until
the red and green LED starts to blink simultaneously.
4HECHANNELSETTINGISCOMPLETEDINMODE"
* The LED corresponding to the setting mode blinks.
Mode A: Red blinks 3 times
Mode B: Green blinks 3 times
44URNOFFTHERECEIVER
Operation Mode Select
The operation mode is on "Normal mode" from factory
shipping. When to change the mode, please follow the steps
shown below.
14URNOFFTHERECEIVER
2Press and hold the Link/Mode switch and turn on the
receiver. Keep the switch hold more than one(1)
SECOND4HELEDSTARTSFLASHINGWITHTHECURRENT
status.
3Release the switch.
44URNOFFTHERECEIVER
By doing this step, the mode can switch over between two(2)
modes.
0 to 1 sec. More than 1 sec.
0 sec. 1 sec.
Press and Hold
Turn on the receiver.
No function
Showing the CURRENT
mode with blink.
Red Blink = Normal
Green/Red Blink =
High Speed
Solid as the mode changed.
Red Solid = Normal
Green/Red Solid = High
Speed
(Become Red after one (1)
second)
㧔Function㧕To change the mode between
Normal and High Speed
㧔LED
Status㧕
Please check the operation mode by observing the LED when
turning on the receiver. If possible there's no FASST transmitter
turned on around you in order to make firmer check.
When turn on the receiver, the LED will be;
s2EDWHENON.ORMALMODE
s'REENAND 2ED MAKES /RANGE WHEN ON(IGH3PEED MODE
!FTERTWOSECONDSCHANGETO2ED
If there are some FASST transmitter turned on around the
receiver, the LED may show the above status for a brief
moment then changed to the status indication as shown in the
"LED indication" table.
LED Indication
'REEN Red Status
Solid Solid Initializing
Off Solid .OSIGNALRECEPTION
Solid Off Receiving signals
Blink Off Receiving signals but ID is unmatched
Link to the transmitter
1Press and hold the Link/ModeSWITCHMORETHANTWO
seconds.
Re-adjust the F/S position (only for TM-8)
1Press and hold the Link/Mode switch between one(1)
ANDTWOSECONDS
0 to 1 sec. 1 to 2 sec. More than 2 sec.
0 sec. 1 sec. 2 sec.
Press and Hold
No function
With TM-8
(not included in this set)
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
Other than TM-8
(not included in this set)
Re-link(ID set)
ｎWARNING
ｌ$ONOTPERFORMTHELINKINGPROCEDUREWITH
motor's main wire is connected or the engine is
operating as it may result in serious injury.
ｊWhile the linking is done, please cycle receiver
POWERANDCHECKIFTHERECEIVERTOBELINKEDIS
really under the control by the transmitter to be linked.
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: [phone], Facsimile: [phone]
1M23N17434 ©FUTABA CORPORATION 2010, 10 (1)