FUTABA T16IZ Manual

1M23Z07715
GYA553Ver.2
T16IZ
Settingmanual

2
ConnectionT16IZandGYA553
T16IZ
S.I/F
CGY 接続コード（ジャイロに付属）
GYA553
ReciverConnectionCable
(includedwithgyro)
Byinstallingthelatestsoftware(Ver.3.3~)ontheT16IZ,youcan
settingtheairplanegyroGYA553ontheT16IZ.
CAUTION
BesuretoconnectanddisconnecttheGYA553
andT16IZconnectioncablewiththepoweroff.

3
1.Select“Gyrosetting”onthelastpageof
AirplaneModelMenu
3.Homescreenisdisplayed
ToBasicmenu
◆ WhencopyingdatafromGyroAtoGyroB
ConnectthegyroAtotheT16IZandpress[Start].(EnterthedataofAintoT16IZ)
ConnectGyroBtoT16IZandpress[GYSettingsTransfer].(PutdataonAintogyroB)
2.Select"Start"
Select"Start"
Thiswilldownloadthegyrodatato
theT16IZ.
*Atthistime,ifGyroisnotconnectedto
T16IZbywire,thisscreenappears.
Tap"Yes"todisplaytheGYA553datasaved
inT16IZ.
1
3
2
SETTING
When"GYSettingsTransfer"is
selected,thegyrosettingdatasaved
inT16IZiswrittentothegyro.
IfyoupressStarthere,theBdatawillbedownloadtothe
T16IZandtheAdatawillbelost.

4
On the home screen, basic information such as gyro operation mode,
sensitivity, battery voltage are displayed.
Homescreen
Homescreen
Gyro operation mode / Gyro
gain
Displays "AVCS" or "Normal"
opera-tion mode and gyro
gain of aileron (roll), elevator
(pitch) and rudder (yaw) axis.
GYA553 Software version
Battery voltage
Displays the voltage of the
receiver battery connected to
GYA.
Homescreen
Basicmenu
Basicmenu
Basicmenu
◆ Config
◆S.BUSbasic
The software version of
the connected GYA553 is
displayed.

5
Config
Config
Set the mounting direction of GYA. Set mounting direction
ZLWKUHIHUHQFHWR¿JXUHEHORZ
Selectwingtype
Config 1/7 Gyrosetmountingdirection
Config 1/7 WING/TAIL
Selecttailtype
Set with the wing type/tail type of GYA553. The wing type/tail type of the transmitter is not used and is normal.
・7XUQR൵WKHHOHYRQ9WDLOPL[LQJRQWKHWUDQVPLWWHUVLGH
・'RQRWXVHWUDQVPLWWHUVXEWULP$GMXVWXVLQJWKHJ\URQHXWUDOR൵VHW
・:KHQXVLQJWKH6%86VHUYR\RXFDQDOVRXVHWKHQHXWUDOR൵VHWIXQFWLRQRIWKH6%86VHUYRVHWWLQJSDUDPHWHUV

6
Config
Config
Select the servo type according to the servo to be
used.
Digitalservo→DG:285Hz
Analogservo→AN:70Hz
7KHVWDELOLW\RIGLJLWDOVHUYRPRGHRIDIOLJKW
LQFUHDVHVLQRUGHU WRSHUIRUPD KLJKVSHHGFRQWURO
action.
Select the SB/R2 port.
Config 1/7 Servotype
Config 1/7 SB/R2OUT
Digitalservo Analogservo
S.BUS
S.BUSdevicescanbe
connectedtothisport.
Whenusingtworudderservos
Rudder2 Throttle
Headdirectionmark
MODESW DATASW
MODELED
Aileron
Programbox S.BUS2
Aileron2
Elevator Elevator2
Rudder
S.BUS/Rudder2
DATALED

7
Config
Config
Neutral position setting for each servo.
Thiswillmovetheneutraltothedesiredposition.
Config 2/7Gyrodirection
Config 3/7 Neutraloffset
It is the direction settting of the gyro. Be careful as it will crash if the direction is reversed.
For dual aileron, dual elevator, and dual rudder aircraft, check the operating direction of each second
aileron/elevator/rudder.
Tilttheairplanetotheleft
onthegroundandcheck
thattheaileronsoperateto
theright.
Raisetheairplanewithits
noseupwardandcheck
thattheelevatoroperates
downward.
Turntheairplanetotheright
onthegroundandcheck
thattherudderoperatesto
theleft.

8
Config
Config
This is the limit setting for each servo. The
SRVLWLRQRIWKHPD[LPXPRSHUDWLRQLVUHDGLQWRWKH
J\URLQWKH¿UVWVHWWLQJ
Config 4/7 5/7 Servolimit
Sticktofullright
Sticktofullleft
Adjustthevalue(%)toreachthe
maximumoperatingposition
Maximumangle
Adjustthevalue(%)toreachthe
iiii
Maximumangle
Aileronexample

9
Config
Config
Config 7/7 Reset
Config 6/7 HoldingPower
Reset each Config item. It returns to the initial
value.
C1-C5switch
button
Withtheswitchbutton,the
"holdingpower"ofeachrate(C1to
C5)canbedisplayedandadjusted.
C1 C5
-100% 100%-35% 35%0%
C1 C3 C5C4C2
-100% 100%-25%-75% 75%25%0%
-100%
100%
0%
The current rate numbers C1 to C5 are displayed by operating the channel of the transmitter.
/LNH WKH ÀLJKW FRQGLWLRQ IXQFWLRQ RI WKH WUDQVPLWWHU \RX FDQ VHW XS WR  GL൵HUHQW GDWD IRU WKH DWWLWXGH
KROGLQJIRUFHUDWHRIWKHDLUFUDIWLQ$9&6PRGHE\RSHUDWLQJWKHVZLWFKIURPWKHWUDQVPLWWHUDQGVZLWFK
between them. You can set the holding power rate selector switch to the channel with the AFR function of
the transmitter, and set the point for each rate on the AFR point curve to switch. It is also possible to use
WKHÀLJKWFRQGLWLRQIXQFWLRQWRZRUNZLWKWKHÀLJKWFRQGLWLRQVZLWFK
When set to SW of DG1 or DG2
Switch channel rate
Channel rate
C1
C5
S.BUSBasic2/3Config6/7
Displayandadjustthecurrentrate
numbersC1toC5byoperating
thechannelonthetransmitter.
Byoperatingthechannelofthe
transmitter,thechannelposition
ofthecurrentratenumbersC1
toC5willbedisplayedingreen.
,WLVDIXQFWLRQWRDGMXVWWKHSRVWXUHKROGLQJIRUFHRIWKHDLUFUDIWLQ$9&6PRGH
Decreasing the value weakens the holding power and makes the operation feeling closer to the normal
mode.
When set to dial or lever

10
SBUSBasicmenu
SBUSBasicmenu
WARNING
AlwaysverifythattheS.BUSfunctionassignments
matchyourtransmitterʼ sfunction(intheFUNCTION
menu)assignments.Ifanychangesaremadewithin
thetransmitterfunctionassignments,thenitwillalso
benecessarytomakethechangeswithintheS.BUS
functionassignments.Tochangethechannel,GYA553
andT16IZmustbeconnected.
The channel of each function can be changed.
ON-OFFchannelforauto
recovery
ReseteachS.BUSfunction.It
returnstotheinitialvalue.
!10CHON
Set the CH for each function according to the transmitter to be used. Any unused functions should be set
to INH (Inhibited).
HoldingPowerC2toC5
TaptheCHusedforrateswitching
toselectit.
Taptomovetotherate
switchingCHsettingpage.