Futech SATURN 2.0 RED User manual

USER
MANUAL
011.20R SATURN 2.0 RED
011.20G SATURN 2.0 GREEN
EN ENGLISH
Manual
in your language?
Check the back cover

2
07
08
01
03
02
04
06
05
OVERVIEW
KEYPAD
A Receiver mode button
B Horizontal laser line / Power button
C Vertical laser line
D Receiver mode LED indicator
E Power LED indicator
F Slope warning LED indicator
F
E
B
C
D
A

3
CASE
01 USB-C socket (for power)
02 Battery compartment
03 ON/OFF - Pendulum lock switch
04 1/4” Tripod connection
05 Vertical laser exit
06 Horizontal laser exit
07 USB-C connector (for charging)
08 LI-ION battery
QUICK START GUIDE
KEYPAD
NAME FUNCTION
A Receiver mode button Press (De-)activate receiver mode (pulse)
BHorizontal laser line/
Power-button
Press (De-)activate horizontal laser lines
Hold Turn on/off device in Locked (manual slope) mode
C Vertical laser line Press (De-)activate vertical laser lines
D Receiver mode LED Off Receiver mode is off, detection with receiver is not possible
Red Receiver mode is on, laser line pulses and detection with receiver is possible
E Power LED Flashin Battery low (around 30mins remaining)
Green Device is switched on
F Slope warning LED Orange ashing fast Device is out of self-levelling range
Orange ashing slow Slope active (pendulum is locked, laser not levelled)

4
SAFETY
Please read the complete safety instructions in
the booklet delivered with this device.
Use extreme caution when the laser beam is
turned on.
Do not aim the laser beam at any gas that may
explode.
LASER RADIATION – Class 2 Laser product. – Do
not stare into beam.
BATTERY
Type of battery: 7.4V Li-ion battery (2200 mAh)
Type of charger for battery: 5V-1A
NOTE
The battery should only be charged with the
included cable.
Charging only happens when the cable is
plugged in and and connected with the USB-C
connector (for charging) [07] which is situated
on the battery [08].
Connecting the cable to the USB-C socket (for
power) [01] does NOT charge the battery!
The product can also be powered directly from
main power when the battery is unable to power
the device (i.e. battery is missing/not charged).
Using the USB-C port (for power) [01] on the
device and the included power supply cable, the
product will work normally.
When the [E] Power LED starts ashing, the
battery is running low. This warning tells the user
that the device will work for ±30 minutes before
powering off.
FIRST TIME USAGE
Remove all protection foils.
USE
AUTO-LEVELLING
ON
OFF ON
OFF
Slide the ON/OFF / Pendulum Lock switch [03] to
the ON side. The switch will hide ‘ON’ and ‘OFF’
becomes visible. The power LED indicator [E] will
turned on. The pendulum levelling mechanism is
released, and the instrument will align on its own.

5



< 3°
The Horizontal laser line will light up. Make sure
that the instrument is placed on a at surface with
a maximum slope of 3,5°.
> 3°



If the slope exceeds 3,5°, the lasers will start
blinking. The slope warning LED indicator [F]
start blinking too.
SLOPE MODE
ON
OFF
3 sec.
+
To work in manual slope mode, the pendulum
needs to be blocked. Make sure the ON/OFF /
Pendulum Lock switch [03] is in the OFF position
(OFF is covered, ON is visible).
· Switch on the device by holding the Horizontal
laser line / Power button [B] for approx. 3 sec.
until the laser switches ON.
MANUAL SLOPE
· Now you can manually tilt the laser using a tri-
pod with a tilting head to get the exact desired
slope.

6
NOTE
In slope mode, the laser lines no longer levelled
automatically. A slow ashing warning indicator
[F] will remind you the pendulum is blocked
and the laser is not able to level.
We advise to use a slope adapter (optional) or
tripod with tilting head (optional) to set slopes.
SWITCHING ON/OFF LASER LINES
When switching on the device,the horizontal
laser diode will be activated.
HORIZONTAL LASER LINES
After the device is ON, the Horizontal laser line
can be switched ON/OFF by pressing the Hori-
zontal laser line / Power-button [B].
…
 
· Press the Horizontal laser line-button [B] a rst
time to switch off the horizontal laser line.
· Press the Horizontal laser line-button [B] a sec-
ond time to switch on the horizontal laser line.
· ... (these two previous steps will repeat)
NOTE
We advise to set the horizontal line on your
working height, using a tripod.
VERTICAL LASER LINES
After the device is ON, the Vertical laser line can
be switched ON/OFF by pressing the Vertical
laser line button [C]. The vertical laser line always
forms a perfect 90° angle with the horizontal
laser line.
…
 
· Press the Vertical laser line-button [C] a rst
time to switch on the verical laser line.
· Press the Vertical laser line-button [C] a second
time to switch off the vertical laser line.
· ... (these two previous steps will repeat)

7
RECEIVER MODE
When working in a bright environment (e.g.
outdoors) or over longer distances, laser lines
become less visible to the human eye. To nd the
laser lines in those situations, this laser can be
used with a laser receiver.
· To activate the Receiver mode, press the receiv-
er mode button [A]. The receiver mode LED
indicator [D] will light up and you will notice the
activated laser lines decrease slightly in bright-
ness. In receiver mode, the laser line will start
blinking very fast (pulse at 10KHz) to allow the
laser receiver, which operates by pulsed light,
to detect the laser line.
· To deactivate the receiver mode, press the
Receiver mode button [A] again. The receiver
mode LED indicator [D] turns off and the bright-
ness of the active laser lines will increase again.
NOTE
All Futech lasers will use 10Khz as frequency in
receiver mode. Only receivers that can detect
laser lines at 10KHz are compatible.

8
TECHNICAL SPECIFICATIONS
MODEL 011.20R
SATURN 2.0 RED
011.20G
SATURN 2.0 GREEN
Visibility
Accuracy ± 2 mm / 10 m
Range with receiver 50 m
Range without receiver 15 m
Levelling range ± 3.5°
Levelling Pendulum levelling
Slope function Manual (via pendulum lock)
Tripod thread 1/4”
Pendulum lock Present
Transport safety mode Present
Amount of laser diodes 2
Laser frequency (receiver mode) 10kHz
Laser wavelenght 635nm 520 nm
Laser classication Class 2 < 1mW Class 2 < 1mW
Power supply Li-Ion battery 7.4V, 2200mAh
Battery life (all lines on) ± 25 – 30h. ± 8 – 9.5h
Protection IP54
Dimensions (l x w x h) 105 x 60 x 95 mm
Weight 0,42 kg
Operation temperature -5°c ~ +40°c

9
DECLARATION OF CONFORMITY
Futech (Belgium) declares under its own responsibility that
this device:
- 011.20R, SATURN RED
- 011.20G, SATURN GREEN
is in conformity with the standards
EN 61326-1:2013
following the provisions of Directive(s)
EMC 2014/30/EU.
Lier, Belgium,
March 30, 2023
Patrick Waûters
Potential misprints are reserved. Images used are not strict. All features,
functionality and other product speci cations are subject to change without
notice or obligation.

10

11

@futechtools
Facebook
@futechtools
futechtools
LinkedIn
YouTube
futech-tools.com
World Wide Web
230517100632
DA DANSK
DE DEUTSCH
ES ESPAÑOL
ET EESTI KEEL
FI SUOMEN KIELI
FR FRANÇAIS
IS ÍSLENSKA
IT ITALIANO
NL NEDERLANDS
NO NORSK
PT PORTUGUÊS
SL SLOVENŠČINA
SV SVENSKA
USER MANUAL
other languages: