G4S S880 Guide

Mount the backplate using countersunk headed screws
adjacent to the opening edge of the door and at a
convenient height (recommended height is 5' (1.5m) to top
of unit).
If fixing hole ’A’ is used then the breakout must be removed
and the screw must not protrude.
Feed the required cables through the backplate:
·The cable from the controller.
·General Purpose Input / Output cable (Optional)
If wall tamper function is to be used then breakout ‘B’ must
be removed and an appropriate wall screw fitted through
the hole to actuate the tamper lever.
2
1Mount the Backplate
Reader Connections
The S880
reading HID format card, with Graphic LCD and keypad. The
reader can be set to use Wiegand or
is a 125kHz proximity card reader that is capable of
®
20mA current loop
communications.
For additional information regarding the installation,
configuration and proper use of this product:
SMS User Guide, P/N 9600-0429, M2150 Access Control
Design Guide, P/N 9600-0420, M2150 Intrusion Guide, P/N
9600-0540 and M2150 UL1076 Compliance Manual, P/N
9600-0449.
The securing screws ‘C’ are integral to the backplate and are unscrewed via the small holes in the
enclosure so that the screw heads locate in the counterbored holes on the inside of the
enclosure.
You should find that
the backplate has
holes for connection
to most standard
electrical backboxes.
C
AB
Installation and User Instructions for S880 Readers
0V
RX+
RX-
TX+
TX-
12V
Controller
0V
TX+
TX-
RX+
RX-
+V
Reader
TB1
20mA current loop
0V
Green
Data 0
Red
Data 1
12V
Controller
0V
GRN
0
+V
Use Belden
9537 Cable
Wiegand
RED
1
Reader
TB1
Connect shield at
controller end
only.
Connect shield
at controller end
only.
Twisted pairs (use
Belden 9503 Cables)
Note: Use LK2 to select the communications mode (See Step 3).
Note:
1). Consult local AHJ (Authority Having Jurisdiction) when installing access control readers and locking
mechanisms to any portal in an egress path.
2). The use of Fail Closed / secure configuration shall be determined by local building codes and the local
AHJ.
3). Wiring methods shall be in accordance with NEC (National Electrical Code) ANSI/NFPA 70.
4). The Wiegand connections are not allowed under UL1076 unless a separate tamper switch is provided.

3Reader Links
Present the card face-on to the reader until you hear a "bleep". Cards can be presented in rapid
succession; there is no need, for example, to wait for "UNLOCKED" to disappear before presenting
another.
If the reader has been enabled for user-code mode at the controller, you can gain access by pressing the
Okey, entering your card number, then pressing the Pkey.
A Setup menu can be displayed by pressing the Oand Pkeys simultaneously while power is applied. You
can use the menu to change the contrast and language used for the LCD (default English). Use the four
function keys to navigate around the menu.
Please refer to M2150 Intrusion Guide, 9600-0540 for IDS Arm / Disarm procedure.
9600-0568. Installation and User Instructions for S880 Readers,
Issue 1.0 18th August 20111. G4S Technology, 2011.
FCC Notice: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Any unauthorized modification to this device may void the authority of
the user to operate it. All trademarks acknowledged.
©
LED Status Indicator
GREEN –The lock is released and you may open the door.
RED –You do not have access rights to gain entry, or the reader did not read your card properly (in
this case, present it again).
YELLOW –Enter your PIN. If you make a mistake, the message INVALID PIN is momentarily
displayed, followed by ENTER PIN, to prompt you to try again.
Specifications
Input voltage: 9-14Vdc.
Input current: 200mA @ nom. 12Vdc.
Operating temperature: 14 to 131°F (-10 to 55°C)
Operating humidity: 15 to 90%, non-condensing.
Maximum read range: 4" (100mm).
Approvals: EN50133, EN300330, EN301489
4Using the Reader
Set LK2 (COMMS) across the center and WE pin for Wiegand communications, or across the center and
CL pin for 20mA current loop communications. Set LK3 (USER Keypad audio feedback) to 1 for sound
on, or 0 for sound off.