Gainsborough SD8 User manual

PLEASE TURN PAGE FOR INSTALLATION STEP 8.
E
T
H
L
C
I
S
Y
P
C
A
E
C
R
K
E
A
S G
A
I
N
E
G
L
P
5. 6. 7.
Spindle Selection Spindle and Slide Assembly Furniture Installation
3.
Cylinder Installation
156mm
16mm
Door Cutout
Select the exterior furniture assembly to
be placed on the outside of your door, then
insert the two screw spiggots into the
exterior lever plate.
Install the exterior plug as shown.
Insert the lock body into the door cutout.
Secure the lockbody with two #8 x 13mm
lockbody screws.
lock body
door cutout
lock body
screw
The sticker on the rear of the lockbody is to
assist in easy installation. - Do not remove.
If the sticker has been broken or removed,
ensure that the rear slide is pushed
completely down before assembling the
lockbody into the door cutout.
lockbody
sticker
rear slide
Insert the key and turn to locked position.
Insert #10 x 38mm cylinder screw & tighten.
Note: Test - beak should not depress.
Assemble the cylinder through the lock so
the cylinder protrudes equally from both sides.
Note: The cylinder cam must rotate as
shown below. (cam turns towards front of door)
Turn key to unlocked position and remove key.
Place the exterior furniture assembly over the
cylinder and hold it against the door.
Note: Ensure the
and spindle are guided into the lockbody.
square drives on the lever
Push the two plugs provided into the screw
holes in the interior furniture assembly.
using the two #8 x 32mm furniture assembly
screws.
Secure both furniture assemblies together
Visually check if the interior furniture plate
(being fixed on the inside of the door), is
marked with an ‘R’ or ‘L’, and install the
corresponding ‘R’ or ‘L’ spindle. The remaining
spindle can be discarded.
Assemble the spindle, slide and retaining
plate as shown below.
IMPORTANT : If installing SD8 with a multipoint accessory
kit, be sure to follow the cylinder installation procedure
within the multipoint kit instructions.
4.
Exterior Furniture Preparation
Select the correct spindle according to
diagram below:
Break the spindle pair in two.
1. 2.
Preparation Lockbody installation
(Pk0153) SD8 Instructions (A4) R2
cylinder
screw
beak
cam operation
cylinder
cylinder cam
ILLUSTRATED FITTING INSTRUCTIONS
SD8/SD8PLUS
MADE IN AUSTRALIA BY
for sliding screen doors
L R
LR
screw
spiggots
exterior
plug
used with ‘L’
furniture plate
‘L’ spindle is
used with ‘R’
furniture plate
‘R’ spindle is
Note: Spindle needs to
match the corresponding
‘R’ or ‘L’ furniture plate
Slide
Retaining
plate
Furniture
screws
Screw
plugs
Austral Lock

SD8 - MAINTENANCE LOG
SD8 - CARE & MAINTENANCE
In order to protect your warranty, record all maintenance activity in the following log:
Address of Building :
Name of Door:
Date Activity Signed
Installation
The product must be installed according to the instructions included in the product packaging and the
door should be apertured according to the door “cut-out” dimensions and tolerances shown.
Prior to fitting ensure that:
· Doors stored on site are stored in a clean dry area free from cement, lime, paint, acid etc.
During fitting of the lock ensure that :
· No metal swarf or other contaminants enter the lock body.
· The fixing screws do not damage the product finish.
After installation of the door ensure that:
· The door is correctly adjusted with the correct clearances.
· The lock engages the strike plate correctly.
· The door is protected from building fall-out such as wet plaster, mortar, paint and welding splatter.
If the door becomes contaminated:
· Do not paint the lock body or faceplate.
· Remove wet plaster, cement, mortar and other droppings immediately, using ample clean water and a sponge or rag, to avoid permanent
staining or scratching of the product finish. If removal is delayed and scraping becomes necessary the surface finish may suffer.
Maintenance
Annually inspect the door to confirm that the door operates with the correct clearances, closes and opens without obstruction and confirm that the lock beak
slides easily into the strike plate aperture when the door is closed - adjust the door if necessary.
Annually check that when the door is closed, the lock can be locked by key and by the snib lever.
Quarterly wipe the strike plates with a soapy rag to remove built up debris and to lubricate the strike plate.
NB : The lock assembly has been lubricated for life, and should not be disassembled by the user.
Cleaning Powder Coatings
Every six months, powder coated surfaces should be cleaned to protect the finish. However, in areas where pollutants are more prevalent, especially in
coastal or industrial regions, cleaning should be carried out every two to three months.
To clean the powder coated surface:
1. Carefully remove any loose deposits with a wet sponge.
2. Use a soft brush (non abrasive) or cloth and a mild household detergent solution to remove dust, salt and other deposits. Do not use steel
wool, scrapers, scouring liquids or powders to remove deposits as these permanently scratch the coating surface.
3. Rinse off with clean fresh water.
Cleaning Chrome, Satin Chrome, Gold and Brass Finishes
Plated finishes are susceptible to tarnishing if they come into contact with moisture, wet paint, or water vapour. All plated finishes should be coated with a
non-abrasive furniture or car wax immediately after installation. Plated finishes should be regularly wiped with a non-abrasive furniture or car wax, taking care not
to scratch any protective finishes that are employed to protect the surface and prevent tarnishing.
8.
Strike Plate Installation
receiving channel
strike plate
Fit the strike plate into the lock.
Mark the position of the strike plate on the channel.
Open the door and install the strike plate with two #10 x 13mm pan head screws.
Note: Place the screws in the centre of the slots to allow for adjustment.
Close the door until the strike plate reaches the receiving channel.
Test that the strike plate engages the lock correctly and adjust if necessary.
A division of
GAINSBOROUGH
Hardware Industries Limited
31-33 Alfred Street,
Blackburn,
VIC 3130, Australia
ph 13 14 18
fax 13 18 14
www.ausloc.com
Austral Lock