Gainsborough Z5R Series User manual

ORIGINATION CRM GSH 853 0612
AT 000
Fit here on door edge
Fit here on door edge
BACKSET 60mm BACKSET 70mm
Mark centre-line
of latch hole
Mark centre-line
of latch hole
FOLD HERE
Installation template
for dummy applications
Installation Instructions for Z5R & S5R Series Dummy Lever
and Z5S & S5S Series Dummy Lever
NOTE: Carefully follow these instructions when installing. Screws to be tightened to a recommended 2.5Nm torque.
Step 1.
Step 2.
Install lever assemblies to door: Z5R, S5R, Z5S & S5S Series Dummy Lever
• Remove rosette cover (1a or 1b) from lever assembly.
• Place dummy lever assembly (2) with latch alignment posts (3) against door face.
• Place dummy plate (4) into position, on back of door.
• Fasten lever assembly & dummy plate together with screws (5) & tube nuts (6)
provided: Use long screws for thick doors and short screws for thin doors.
• Install screws (5) from dummy plate side into the vertical tube nut holes (8) of the
dummy leverset under-rose. Then tighten both screw heads.
Z5R & S5R
• Reapply rosette cover (1a) to under-rose by pushing the cover over the rubber ring
until flush with door.
Z5S & S5S
• Reapply rosette cover (1b) to under-rose by pushing the cover
over the rubber ring until flush with door. The *grub-screw, which is
already located in the rosette cover, should be on the lower face.
• Check the rosette cover is square with the door edge. Fasten in place
with *grub-screw using allen key (9) provided.
*Note: Grub-screw is already located in the rosette cover.
25mm hole
x 10mm deep
9mm hole
Important Note:
Don’t drill this hole
through the door.
Gainsborough Hardware Industries Limited,
Melbourne, Australia. A.B.N. 25 004 792 269
www.gainsboroughhardware.com.au
55A1DOC04BT1
JUN ‘12
• Fold Template where indicated.
• Position template on door edge at desired height.
• Firmly hold template & mark 5 hole centres (4 off 9mm
& 1 off 25mm) at required backset.
Note: 25mm hole 10mm deep only.
• Drill Pilot holes - suggest 3mm, then enlarge (4 off) 9mm
holes from both sides of door.
• Drill (1 off) 25mm hole 10mm deep on side of door dummy
leverset will be fitted.
1b
1a
9
2
3
6
4
5
8

ORIGINATION CRM GSH 853 0612
AT 000
Fit here on door edge
Fit here on door edge
BACKSET 60mm BACKSET 70mm
Mark centre-line
of latch hole
Mark centre-line
of latch hole
FOLD HERE
Installation template
for dummy applications
Installation Instructions for Z6R & B6R Series Dummy Lever
NOTE: Carefully follow these instructions when installing. Screws to be tightened to a recommended 2.5Nm torque.
Step 1.
Step 2.
Install lever assemblies to door: Z6R & B6R Series Dummy Lever
• Remove rosette cover (1) from lever assembly.
• Place dummy lever assembly (2) with latch alignment posts (3) against door face.
• Place dummy plate (4) into position, on back of door.
• Fasten lever assembly & dummy plate together with screws (5) & tube nuts (6)
provided: Use long screws for thick doors and short screws for thin doors.
• Install screws (5) from dummy plate side into the vertical tube nut holes (8) of the
dummy leverset under-rose. Then tighten both screw heads.
• Reapply rosette cover (1) to under-rose by pushing the cover over the rubber ring
until flush with door.
25mm hole
x 10mm deep
9mm hole
Important Note:
Don’t drill this hole
through the door.
Gainsborough Hardware Industries Limited,
Melbourne, Australia. A.B.N. 25 004 792 269
www.gainsboroughhardware.com.au
55A1DOC04BT1
JUN ‘12
• Fold Template where indicated.
• Position template on door edge at desired height.
• Firmly hold template & mark 5 hole centres (4 off 9mm
& 1 off 25mm) at required backset.
Note: 25mm hole 10mm deep only.
• Drill Pilot holes - suggest 3mm, then enlarge (4 off) 9mm
holes from both sides of door.
• Drill (1 off) 25mm hole 10mm deep on side of door dummy
leverset will be fitted.
1
2
3
6
4
5
8