Gainsborough Austral Lock Virtus Four Point Hinged Door Mortice... User manual

Contents
1. Lock body
2. Long plate external furniture
3. Long plate internal furniture
4 . Cylinder (not included,
length to suit door thickness)
5. Zinc spindles
6. Furniture fixing screws
7. Cylinder retaining screw
1. 2. 3.
Austral Aurora furniture shown
Virtus Four Point Hinged Door Mortice Lock
Installation Guide
Step 1: Door Preparation
1.1 For Flush Mount, route the door as per technical dimensions below
22.0
230.0
5.0
2 HOLES
8.6 CSK
2 HOLES
R2.5 x 4
104
160
87.0
84.5
101.5
17
59.5
122.5
10
30
9 x 2 HOLES
20
16
8
37 REF
R10
1000 mm
TO THE BOTTOM OF THE DOOR
(RECOMMENDED)
35.4
40 60
FLUSH MOUNT INSTALLATION
30mm BACKSET 40mm BACKSET 60mm BACKSET
8. Fixing tabs
4. 5. 6. 7. 8.

Step 2: Installing the Lock
2.1 Insert lock into the stile
2.2 Secure with screws (max length 12mm)
Step 1: Door Preparation (cont.)
1.2 For Face Mount, route the door as per technical dimensions below
192.0
21.0
3.2
2 HOLES
R2.5 x 4
88.5
68.0
144.5
84.5
17
122.5
8
16
10
59.5
R10
9 x 2 HOLES
20
101.5
37 REF
1000 mm
TO THE BOTTOM OF THE DOOR
(RECOMMENDED)
35.4
30mm BS
routing is 27.5mm
from face
TOP VIEW OF STILE
SIDE VIEW OF STILE
FRONT VIEW
OF STILE
40mm BS
routing is 37.5mm
from face
60mm BS
routing is 57.5mm
from face
FACE MOUNT INSTALLATION
30mm BACKSET 40mm BACKSET 60mm BACKSET
Use fixing tabs for flush mount installation
Fixing tab
Fixing tab

Step 4: Re-handing & Latch Adjustment
Step 3: Mounting Accessories
3.1 Insert the spindle into the
square hub of the lock
3.2 Insert the cylinder into the
cylinder hole and secure with
the cylinder retaining screw
3.3 Mount the internal and
external hardware onto the
spindle and cylinder
3.4 If using snib furniture, align snib
arm to snib slot in lock body
3.5 Secure furniture with supplied
fixing screws
4.1 Check latch to determine if handing
is correct
4.2 To re-hand the latch, remove cap,
turn the latch, head screw counter-
clockwise with a manual screw driver
until the back of the latch comes out
of the faceplate so it can be rotated
4.3 Rotate the latch head 180 degrees
and re-tighten the screw fixing
4.4 To increase the latch projection
turn the latch screw counter-clockwise
4.5 Latch projection can be increased
by a maximum of 2mm from original
position
4.6 Replace cap after adjustments are
complete

Step 5: Shoot Bolt Assembly
5.1 Cut the shoot bolts to the required
length as per instructions below:
• Measure the distances as
shown
• Use the formula below and cut
the lengths (lengths include
threaded end piece)
Top Rod (TR) = Panel Height (PH)
- Handle Centre (HC) -98mm
Bottom Rod (BR)
= Handle Centre (HC) -154mm
(Using this formula will result in
the shoot bolts being flush with
the top of the door panel)
5.2 Insert D-bolt into top/bottom of rods
5.3 Crimp D-bolt to retain and hold
5.4 Insert rods from the top and
bottom of the stile and screw
into the lock. Magnets in throw bolts
will assist in locating rods
5.5. Retain D-bolts in stile to prevent
rotation but allow throw
BOTTOM ROD (BR)
45
120
64
TOP ROD (TR)
45
6
6
PANEL HEIGHT (PH)
HANDLE CENTRE (HC)
BOTTOM ROD (BR)
11
TOP ROD (TR)
11
END OF ROD
END OF ROD
1800 098 094
[e-mail]
ausloc.com
©Allegion 2023
PDAU0004