GALLUNOPTIMAL SPRINT80+ User manual

GALLUNOPTIMAL Soldering Iron SPRINT80+
Change the cartridge soldering tip: Important NOTE!
Switch off the device to change the cartridge soldering tip! Let the soldering tip cool down to room
temperature to prevent burns! Push back the handle pad (silicone cover) on the soldering iron and loosen
the grub screw for fixing the soldering tip. Use an optionally available silicone pad for optimum extraction
and protection from any residual heat. Only original GALLUNOPTIMAL replacement cartridges for
SPRINT80+ & 80D+ may be used and inserted into the handle! Then lightly tighten the screw again to
secure the cartridge soldering tip! Never change a soldering tip with the grub screw tightened,
otherwise the cartridge tip may be damaged when pulled out!
Switch on: Press the slide switch, the LED starts flashing very fast and signals the heating up to the
setpoint. Slow flashing means that the SET temperature has been reached. If the LED does not light up,
the soldering tip temperature is higher than the SET temperature.
THANK YOU FOR PURCHASING A GALLUNOPTIMAL SOLDERING IRON. Please read the operating instructions
before operating and keep them in a safe place easily accessible to all users.
Before leaving the factory, the soldering iron is subjected to a test. This results in the soldering tip being covered
with solder and may be slightly discolored. This does not represent a defect.
Features:
Soldering iron with precise temperature control
Rapid cartridge soldering tip system
Ergonomic handle
Temperature adjustable via rotary control on the
soldering iron
Calibration function
Technical Data:
Input Voltage 230VAC
Power 80W
Temp. range 200-500°C
Temp. stability +/- 2°C
Temp. unit °C
Impedance tip-ground <0,1 Ω
Voltage tip-to-ground <2mV
Connection cable 1,28m
Weight 160g
WARNING
Failure to observe the following instructions may result in serious injury or death to the user.
If the device is switched on, the soldering tip automatically heats up to the last set temperature.
There is a risk of burns on the metallic surfaces!
The device is designed for soldering soft solder at different temperatures. Any other use is not permitted.
Do not touch the metallic parts on the tools during operation and immediately after switching off, CAUTION! Risk
of burns!
Do not use the device in the vicinity of flammable substances and components.
Use a heat-resistant work surface and keep your workplace clean.
Solders, fluxes and heated materials can develop harmful properties and should be exhausted in a controlled
manner. Do not inhale these toxic fumes or gases and provide adequate ventilation.
The device may only be used in dry rooms. Protect the device from liquids and moisture. Do not touch the device
with wet hands. Otherwise, short circuits and electric shocks could be triggered.
Inform other persons in the working area that the temperature can be very high during operation. Switch off the
device as soon as the work is finished to avoid danger.
Do not leave the device unattended while it is switched on.
After switching off, wait until the heated parts have reached room temperature if you want to touch or change
parts on them.

Tel. [phone]
e-mail: i[email protected]
www.loet-shop.de
Bräunlich GmbH
Am Heideberg 26
D-06886 Lutherstadt Wittenberg
Calibrate the soldering tip temperature: Clean the soldering tip and wet it with solder. An oxidized
soldering tip can otherwise produce temperature measurement errors. Then set the temperature control
knob to 350°C, wait until the temperature has stabilized and then measure the soldering tip temperature.
Turn the screw labeled CAL in small increments until the measured temperature corresponds to the set
value of 350°C +/-5°C. Give the heating element time to compensate between cooling down and
reheating.
Error
Testing
Solution
No function after power on
Is the power cable plugged in
correctly?
Disconnect and reconnect the power
cord.
Soldering tip is sometimes not hot
enough.
Is the soldering tip inserted
correctly?
Check soldering tip for correct fit
and insert accordingly.
Solder does not melt, despite
correctly set temperature.
Measure the temperature at the
soldering tip.
Calibrate soldering tip temperature
or replace cartridge soldering tip
EU Declaration of Conformity according to Low Voltage Directive 2014/35/EU (No. 01-20)
The manufacturer / distributor
Bräunlich GmbH
Am Heideberg 26
06886 Lutherstadt Wittenberg
hereby declares that the following product
Product name: GALLUNOPTIMAL Soldering Iron
Trade name: GALLUNOPTIMAL SPRINT80
Model name: GOSPRINT80+
complies with the provisions of the Low Voltage Directive 2014/35/EU - including its amendments in force at the time
of the declaration.
The following harmonized standards have been applied:
"DIRECTIVE OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL on the harmonization of the laws of the Member
States relating to electromagnetic compatibility".
The following national or international standards (or parts/clauses thereof) and specifications have been applied:
EN 60335-1:2012 + A11:2014 + A13:2017 + A1:2019 + A2:2019 + A14:2019
EN 60335-2-45:2002 + A1:2008 + A2:2012
EN 62233:2008
Location: Lutherstadt Wittenberg
Date: 30.8.2022
_______________________________
(Signature)
Tobias Bräunlich, CEO
Correct disposal of this product
The crossed-out wheeled garbage can indicates that this product must not be disposed of with
other waste in the household waste throughout the EU. To avoid harm to the environment or
damage to health, recycle the product responsibly to promote the sustainable reuse of material
resources. For an environmentally sound disposal of your old device, please use the return and
collection systems. For more information, please contact your city or local authority. Or contact
the dealer from whom you purchased the product.