Gama Sonic AURORA User manual

AURORA SOLAR LAMP
Model: GS-124B-FPW
Version 1.1
US Patent #9458970
Instruction Manual
Post/3"Fitter Mount
Pier Mount
Wall Mount

Solar Lamp Location:
Tools that are needed but not supplied with the solar post
lamps are: a screwdriver, power drill.
For optimum light duration throughout the night, it is very important
to place your solar lamp in a spot where it will receive the maximum
amount of direct sunlight throughout the day.
Note: The unit will operate optimally after 2 full days of charging.
Open your package and remove the contents. Check to make
sure all pieces are present and accounted for.
page 2
Thank you for your purchase.GAMA SONIC® solar charged lighting eliminates the problems
associated with most solar lighting available today. GAMA SONIC® solar charged lights are
brighter and last all night with a full day solar charge. Unique designs, superior light output,
and numerous installation options confirm the outstanding value of our product.
For technical assistance and more information call our Toll-Free number:
800-835-4113 (only within the US)
Or
visit our website or download the latest version of your instruction manual:
www.gamasonic.com Or www.gamasonic.com/user-guides
Please read the instruction manual carefully to obtain the best results from your purchase.
A. Top & Bulb
D. Wall Mount
E. Flat Base F. BoltB. Fixture C. Fitter
What’s Inside:

page 3
Note: There are specific types of screws for specific
surfaces. If unsure of the appropriate type of screw to use
on your desired surface, please consult a professional.
1. Use a drill to make two holes in the desired surface.
2. Use the appropriate mounting hardware to secure
your lamp to the desired surface.
3. Screw the fixture (B) into the flat base (E)
using bolt (F).
1. Using the wall bracket (D) as a template,
drill two holes in the wall and place
appropriate hardware into holes.
2. Place the wall bracket in line with the holes
and secure bracket to wall.
3. Screw the fixture (B) into the wall
mount (D) using bolt (F).
Note: If you are replacing an existing gas/electric
post light, you must consult a certified technician
to disconnect them before installation.
1. Screw the fixture (B) into the fitter (C) using
bolt (F).
2. Place the unit on top of the existing 3” post
and tighten it using the screws provided.
1. Remove part (A) from part (B) by
removing the 2 screws as shown in Fig. 1.
2. Screw in provided A-50 Gama Sonic
bulb while gripping the base only (Fig. 3).
3. Turn the operation switch (Fig. 2) to the
HIGH/OFF/LOW position, and the solar
lamp will automatically operate from
dusk to dawn. Reattach part (A) to part
(B) and secure with the 2 screw.
Operation Instructions
Installation Instructions
Fig. 3
Fig. 4
Bolt
(Fig. 4)
Pier (Flat) Mount
Wall Mount
Post/3"Fitter Mount
(Fig. 5)
Fig. 6 (Fig. 6)
3” post
Fig. 1
Fig. 2
OPERATION SWITCH
Fig. 5
Bolt
Bolt

page 4
Replacing the Batteries
Replacement batteries are available
at www.gamasonic.com or via our Toll free number: [phone]
After several years of use, the battery may need replacing.
1. Remove the 2 screws from the top of the lamp and remove the top from the fixture. (Fig. 7)
2. Remove the bulb.
3. Remove the screw from the battery cover.
4. Take the battery out of its secured position and unclip its wire. Clip your new battery in and
reinstall the lamp in reverse order.
This lamp takes a 3.2V/1500 mAh Li-Ion battery pack.
Replacement batteries can be purchased through our
authorized dealers or by going to www.gamasonic.com
WARNING: Do not dispose of Li-Ion batteries in the regular trash,
municipal waste stream or by fire as batteries may leak or explode.
Do not open, short circuit, or mutilate batteries as injury may occur.
Preserve our environment by recycling Li-Ion batteries or disposing
of them in accordance with local, State and federal regulations. Do
not mix old and new batteries.
Maintenance
Clean the solar module regularly with a damp towel to guarantee optimum performance
of the solar panel. Do not use any type of solvent for cleaning and be careful not to put too
much pressure on the module while cleaning.
Trouble Shooting
If your solar charged light does not come on at dusk despite
observance of all the instructions, please try the following steps:
1. Make sure that the solar light is not being affected by any other light source.
2. Ensure the solar light is not positioned in the shade during the day.
3. Make sure the switch in the lamp head is in the” ON” position.
4. Check that the batteries are installed correctly.
NOTE: The performance of the solar light will vary with the time of year. It will deliver
longer duration when it has had a full day in the sun rather than a day in overcast
weather.
WINTERTIME TIPS: For optimal performance, be sure to remove any snow or debris
accumulation from solar panel(s). A solar panel free of debris will charge the batteries
much more efficiently.
WARNING: Please keep out of reach of children.
Fig. 7