Gama Sonic GS-94S User manual

Introduction
Thank you for your purchase. GAMA SONIC®solar charged accent lighting eliminates
the problems associated with most solar lighting available today. GAMA SONIC®solar
charged lights are brighter and last all night with a typical solar charge. Unique
design, superior light output and numerous installation options confirm the
outstanding value of the product.
GAMA SONIC®has been recognized as a worldwide leader in the lighting industry for
over 20 years. The company also offers unique multi-purpose rechargeable products
that range from party lights to emergency lighting products.
For technical assistance and more information call our Toll Free number:
800-835-4113 (only within the US) or visit our website at:
www.gamasonic.com.
VICTORIAN
SOLAR LAMP
US Patent # 7172307
Instruction Manual
Model: GS-94S/D/T
Model: GS-94FPW

Please read the instruction manual carefully to obtain the best results from your
purchase.
Unpack and identify the following components.
Parts: GS-94S Parts: GS-94D Parts: GS-94T
A
B
C
D
E
F
G
H
I
K
J

Tools that are needed but not supplied with the high post solar lamp set are: a screw
driver, a wrench and an electrical drill that will be used to anchor the lamp base to the
ground.
Solar Lamp Post Location
For optimum light duration throughout the night, it is very important to mount your
solar lamp post in a spot where it will receive the maximum amount of direct sunlight
throughout the day.
Assembly Instructions
NOTE: The following steps are for reference only. Consult your local hardware store
for the best installation method for your particular surface.
NOTE: The solar light must be charged for two sunny days in the “ON” position for
best results.
GS-94S
1. Turn the On/Off switch in the lamp head (A) to Low or High position
(Fig. 1).
2. Use electric drill to make three holes into a solid surface no smaller
than the fastening screws (G). The holes shall be lined up with the
holes of the lamp base (F).
NOTE: For installation in the ground where pouring concrete is not
preferred or possible, use our GS-3 EZ Lamp Post Anchor (sold
separately) to quickly and easily secure the lamp anywhere in your
yard.
3. Put the fastening screws (G) into the drilled holes with their threaded
ends facing up.
4. Place lamp base onto fastening screws and secure base with the nuts
using a wrench. Cover the bolts with the plastic covers provided.
5. Make sure the lamp base (F) is stable before installing Part (E).
6. Place part (E) on top of part (F) and tighten with the provided screws
using a wrench. 7. Screw part (D) to part (E), part (C)
to part (D) and part (B) to part (C).
Fig. 1
Fig. 2

GS-94D and GS-94T
1. Repeat steps 1 to 6 as shown in GS-94S.
2. Screw part (D) to part (E). part (C) to part (D) and part (H) into part
(C).
3. Screw bracket (J) into part (H) using the provided screws as shown in
Fig. 3.
4. Repeat step 3, two times in model GS-94D and three times in model
GS-94T.
5. Screw part (K) on top of part (H) for GS-94D or (I) for GS-94T.
Replacing the Batteries
(After several years of use, the batteries may need replacing).
1. Remove the top (A) from the fixture (B)
by releasing the 2 screws (Fig. 2).
2. Make sure the ON/OFF switch is in the “OFF” position.
3. Release the 3 screws on the silver reflector and remove
the old batteries. Make sure the new batteries are
high quality –1 x Li-ion Battery Pack
(3.2 Volt / 3,000 mAh).
4. Install the new batteries into the battery compartment.
5. Reassemble the unit by reversing the above procedure.
Fig. 3

WARNING: Do not dispose of Li-ion battery in the regular trash, municipal waste
stream or by fire as batteries may leak or explode. Do not open, short circuit, or
mutilate batteries as injury may occur. Preserve our environment by recycling Ni-Mh
batteries or disposing of them in accordance with local, State and federal regulations.
Do not mix old and new batteries.
Maintenance
Clean the solar module regularly with a damp towel to guarantee optimum
performance of the solar panel. Do not use any type of solvent for cleaning and be
careful not to put too much pressure on the module while cleaning.
Trouble Shooting
If your solar charged light does not come on at dusk despite observance of all the
instructions, please try the following steps:
1. Make sure that the solar light is not being affected by any other light
source.
2. Ensure the solar light is not positioned in the shade during the day.
3. Make sure the switch in the lamp head is in the”ON” position.
4. Check that the batteries are installed correctly.
NOTE: The performance of the solar light will vary with the time of year. It will
deliver more light when it has had a full day in the sun rather than a day in overcast
weather.
WINTERTIME TIPS: Keep snow and debris cleaned off the solar panels so the
batteries can recharge. If the lights are covered with snow for an extended period of
time, after the snow melts, allow all the batteries to charge in full, direct sunlight for
at least 6 hours to their maximum capacity.
WARNING: Please keep out of reach of children.