Ganz ZN-S1000VE User manual

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 1




ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 2
Table of Contents
1.Introduction............................................................................................................. 3
2.ProductDescription ................................................................................................. 4
2.1.Functionspecification .............................................................................................. 4
3.Installation&Configuration ..................................................................................... 6
3.1.Packagecontents...................................................................................................... 6
3.2.Components ............................................................................................................. 7
3.2.1.FrontPanel ..................................................................................................................... 7
3.2.2.RearPanel ...................................................................................................................... 9
3.3.BasicConnection .................................................................................................... 13
3.4.SerialNumber/MACAddress................................................................................ 14
4.OperationDescription............................................................................................ 15
4.1.FactoryDefaultSettings ......................................................................................... 15
4.2.Rebooting ............................................................................................................... 15
5.PoweroverEthernet(PoE) ..................................................................................... 17
5.1.PoEcompatibility ................................................................................................... 17
5.2.Powerclassification................................................................................................ 17
6.Electricalcharacteristics ......................................................................................... 18
6.1.Operatingconditions.............................................................................................. 18
6.2.Powerconsumption ............................................................................................... 18
7.Dimensions............................................................................................................ 19

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 3
1.Introduction
ZN‐S100VandZN‐S1000VEareencodermodule.ZN‐S100V/ZN‐S1000VEcompress
video/audiodataandtransmitthecompressedvideo/audiodatathroughthenetworkin
realtime.ZN‐S100V/ZN‐S1000VEprovidesahighqualityvideoimagewithalimited
bandwidthandstoragecapacity.ZN‐S100V/ZN‐S1000VEalsosupportsdualstreammode,
andisequippedwithbuilt‐inVCA(VideoContentAnalysis)feature.Theseproductsare
ideallysuitedforawiderangeofsurveillanceandremotemonitoringapplications.Main
featuresarehighlightedbelow.


Mainfeatures
•HighQualityCompressioninrealtimestreaming
•H.264,MPEG‐4,andMJPEGencodingatD1inrealtime

Network
•RTP/RTSPandunicast/multicastaresupported.

Streaming
•Dualstreamingmodesuchasdifferentcodec/resolution/bitrateandsoon.
•De‐interlacingonDSP.

Video/Audio
•Loop‐outvideoforexternalmonitors
•Burnt‐Intextissupported
•ZN‐S1000VEsupportstwowaysaudio.(ZN‐S100Visnotavailable.)

AdditionalFeatures
•RS‐485/422serialportforPan/Tilt/Zoom.(ExceptZN‐S100V)
•RS‐232CserialportforsomedeviceslikeaPOSterminal.(ExceptZN‐S100V)
•Motiondetectionbyhardware.
•OnScreenDisplay(OSD)byhardware.
•POE(PowerOverEthernet)issupported.(Optional)

VCA
•VCAPresence(IncludedasStandard)
•VCASurveillance(Optional)

SDK
•Twotypes(RTSPandHTTP‐API)areprovidedforapplicationdevelopment.

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 4
2.ProductDescription
2.1.Functionspecification
ZN‐S100V/ZN‐S1000VEseriesspecificationisshownasfollowingTable.

ZN‐S100V/ZN‐S1000VEseries
ItemZN‐S100VZN‐S1000VE
NumberofStreamsDualStream,Configurable
Inputchannel1ch
OutputChannel1LoopOut
CompressionH.264,MPEG‐4,MJPEGSelectableperStream
ResolutionD1,4CIF,CIF,QCIF,VGA,QVGA
Video
CompressionFPS25/30fps@D1(PAL/NTSC)
Input/Output Notavailable1/1 c h 
Audio
DataFormatNotavailablePCM&G.711
Network10/100Base‐T
DI/DONotavailable2/2 
RS‐232CNotavailableSupport
RS‐485NotavailableSupport
De‐interlacingSupport(HardwareEncodingEngine)
MotionDetectionSupport(DSP)
OSD Support(DSP)
ProtocolsSNTP,DHCP,UDP,TCP,RTP,RTSP(unicast,multicast)
ExternalStorageNotavailableUSB2.0&SDMemorycardslot
※SDCardisnotincluded
PowerSource12VDC(DCJack)12VDC(DCJack)
PoweroverEthernetSupport‐IEEE802.3af(Optional)
OperatingTemperature0˚C~50˚C(32˚F~122˚F)
OperatingHumidityUpto85%RH(Non‐condensing)
Dimension74.6(W)x26.3(H)x106.6(D)
mm
103.4(W)x37.7(H)x141.4(D)
mm
WeightTBDTBD

VCA(VideoContentAnalysis)
VCAPresence(IncludedasStandard)
HighPerformanceAdvancedTrackingAlgorithm,LowFalseAlarmRate
EasytoUseIntuitiveWebBrowserInterface
DetectionZonesMulti‐segmentPolygonsandLines

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 5
On‐screenDisplayReal‐timeDisplayofTrackingDataandEvents
VCASurveillance(Optional)
DetectionBehaviorDirection,Stopping,Loitering,Entering,Exiting,Appear,and
DisappearFilters
3DBehaviorPerspectiveCorrectedSizeandSpeedFilters
StatisticsCountingFunctionsandOtherStatistics
MetaDataBinaryXMLFormat
ImageStabilization(Optional)
ElectronicStabilizationRemovesCameraSway

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 6
3.Installation&Configuration
3.1.Packagecontents
ThePackagecontainsthefollowing.Pleasemakesurealllisteditemsareincludedinthebox.

ZN‐S100VorZN‐S1000VE‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐1
LANCable(Crosstype1m)‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐1
9portTermin alblockplug(exceptZN‐S100V)‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐2
DC12VPowerAdapter‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐1
AC100~AC240Vpowercable‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 1

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 7
3.2.Components
3.2.1.FrontPanel

Figure1.FrontPanelofZN‐S1000VE

Figure2.FrontPanelofZN‐S100V
①VideoInputBNCConnector(Vin1)
Itismainlyusedforvideoinputs.

②VideoOutputBNCConnector
Thisconnectorisusedforloop‐outofvideoinput.

③,④IndicatorLED(Status,Data)
StatusandDataindicatorsdisplaythefollowingsysteminformation.StatusLEDhasayellow,
agreenandanorangecolor.DataLEDhasared,agreenandadarkorangecolor.

1.Poweroff
ItemStatusData
PowerOFFOFFOFF

①

②
⑥
⑦
⑧
①
②
⑤
③
④


ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 8
2.Systeminitialization
ItemStatusData
InProcessOffBlinkingDarkOrange
NormalStateOrangeOff
AbnormalStateOrangeDarkOrange

3.Kernelbootingup
ItemStatusData
InProcessOrangeGreen
NormalStateOrangeOff
AbnormalStateOrangeGreen

4.Videostreamingservice
ItemStatusData
NormalBlinkingGreenOff
AbnormalGreenOff

5.DSPoperationstatus
ItemStatusData
NormalOrangeblinksatevery1
second
Off
HighOverloadOrangeblinksatevery1
second
Red


⑤SDMemorySlot
Itisamemorycardslotforexternalstorage.
⑥LANConnector(Ethernet)
ItisaRJ45LANconnectorfor10/100Base‐TEthernet.Thissocketcanalsobeusedtopower
theZN‐S100V/ZN‐S1000VEviaPoE(Optional).

Figure3.RJ45LANconnector

⑦PowerAdaptorConnector(DC12V)
ZN‐S100VneedsaDC12V1Aadapterforpowersupply.


‐
+

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 9
Figure4.PowerConnection

⑧ResetSwitch(Reset)
ResetswitchisusedforrestartingZN‐S100V/ZN‐S1000VEorresettingZN‐S100V/ZN‐
S1000VEasFactoryDefault(FD).Referto‘4.1.FactoryDefaultSettings’fordetailed
procedures.

3.2.2.RearPanel

Figure5.RearPanelofZN‐S1000VE
① USBPort
ZN‐S1000VEprovidesoneUSBportwhichcanconnecttotheUSBdeviceasanexternal
storagedevice.ItcanbeconnectedtomultipleUSBdevicesusingUSBHUB.

②Terminalforaaudiooutput/input,analarm,asensorandserialdevices
(Except ZN-S100V)

AOut
AOutGND
DOch1
DOch2
DOGND
RS‐485D+
RS‐485D‐
RS‐485GND
DIGND
DIch2
DIch1
AinGND
AinRS‐232CGND
RS‐232CTX
RS‐232CRX
①

②
⑤
④

③


ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 10
Figure6.Terminalblock

1.AudioInput
ZN‐S1000VEhasonechannelmonoaudioinput.

2.AudioOutput
ZN‐S1000VEhasonechannelmonoaudiooutput.Astheoutputpowerfortheaudioislow,
amplifierspeakerisneeded(Donotuseaheadphoneorearphonedirectlytothecamera).

3.DigitalInput(DI1,DI2)
ZN‐S1000VEsupportstwodigitalinputs.Itcanbeconnectedeithervoltagetypesensoror
relaytypesensorasfollowingFigure7.andFigure8.


Donotusevoltageandrelaytypesensortogether.


Pleasepayattentiontoelectriccharacteristicsduringinstallation.
(Detailedinstructionsarebeingprepared.)


Figure7.VoltageTypeDigitalInputConnection


Figure8.RelayTypeDigitalInputConnection

4.DigitalOutput(DO1,DO2)
DOdevicescanbeconnectedasfollowingFigure9.

ch1
ch2
GND
12
Sensor1
Sensor2
ch1
ch2
GND
12
Sensor1
Sensor2

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 11

Pleasepayattentiontoelectriccharacteristicsduringinstallation.
(Detailedinstructionsarebeingprepared.)


Figure9.DigitalOutputConnection

5.RS‐485
TheRS‐485serialportconsistsofDATA+,DATA‐andGNDasfollowingFigure10.

Figure10.RS‐485Connection

6.RS‐232C
RS‐232CTerminalBlockisusedforsomedevicessuchasPOSterminalblock.


Figure11.RS‐232CConnection

③LANConnector(Ethernet)
ThisisaRJ45LANconnectorfor10/100Base‐TEthernet.Thissocketcanalsobeusedto
powertheZN‐S100V/ZN‐S1000VEviaPoE(Optional).
RX
TX
GND
RXTX
TX
RX
GND
DATA+
DATA‐
GND
+‐
PTZCamera
DATA+
DATA‐
GND
ch1
ch2
GND
12
LED1
LED2+12V

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 12

④PowerAdaptorConnector(DC12V)
ZN‐S1000VEneedsaDC12V1Aadapterforpowersupply.

Figure12.PowerConnection

⑤ResetSwitch(Reset)
ResetswitchisusedforrestartingZN‐S100V/ZN‐S1000VEorresettingZN‐S100V/ZN‐
S1000VEasFactoryDefault(FD).Referto‘4.1.FactoryDefaultSettings’fordetailed
procedures.
‐
+

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 13
3.3.BasicConnection

Figure13.ZN‐S1000VE’sFrontPanelConnection
Figure14.ZN‐S1000VE’sRearPanelConnection

Normaloperationmaynotbepossibleiftemperatureorhumidityexceedlevels
recommendedintheZN‐S100V/ZN‐S1000VEspecification.
USBmemory
LAN
DCAdapter
Alarm PTZCamera
AmpSpeaker
MIC
ExternalMonitor
Camera
SDmemory
Sensor1‐2

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 14
3.4.SerialNumber/MACAddress
SerialnumberandMACaddressisattachedonthebottomasshowninFigure15.

Figure15.SerialNumber/MACAddress
MAC Address
Serial Number
550012345 MAC 00:1C:B8:C0:14:B1
ZN-S1000VE P1331010100000-121

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 15
4.OperationDescription
4.1.FactoryDefaultSettings
Factorydefaultsettingsareasfollows:
•IPaddress:192.168.xx.yy(Referto2.3SerialNumber/MACAddress)
•Mask:255.255.0.0
•Gateway:192.168.0.1
•UserID:root
•Password:pass



ToperformtheFD(FactoryDefault)initialization:

ZN‐S1000VE
Referto‘Figure1.’
1. Turnoffthepower.
2. PressandholdtheResetbutton
3. Turnonthepower.
4. ReleasetheResetbuttonwhentheStatusLED’scolorisorangeandtheDataLED’s
colorisred.
5. Waitforthesystemtoreboot.


ZN‐S100V
Referto‘Figure2.’and‘Figure3.’
1. Turnonthepower(TheStatusLEDison).
2. PressandholdtheResetbuttonwithin1second.
3. ReleasetheResetbuttonafter3seconds.
4. Waitforthesystemtoreboot.
4.2.Rebooting
Torebootthesystem:

ZN‐S1000VE
Referto‘Figure1’
MACaddress=00‐1C‐B8‐C0‐14‐B1 →IPaddress=192.168.35.69
ConverttheHexadecimalnumbertoDecimalnumber

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 16
1.PressReset.
TheredDataLEDwillblinkseveraltimes.WhenResetfunctionisactivated,thered
DataLEDwillturnon.UsermaystoppressingResetatthispoint.
2.When“Reset”functionhasbeencompleted,
thegreenDataLEDwillturnonandStatusLEDandDataLEDwillblinktogether.

ZN‐S100V
Referto‘Figure2’and‘Figure3’
1.Whilethecameraisinuse,pressandholdtheResetbutton.
(BoththeStatusandNetworkLEDsareon.)
2.ReleasetheResetbuttonafter3seconds.

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 17
5.PoweroverEthernet(PoE)
ThePoEmoduleusedinZN‐S100V/ZN‐S1000VEiscommerciallyavailablemodulewithout
modification.ThestandardZN‐S100V/ZN‐S1000VEdoesnotincludePoEmoduleinit.PoE
moduleisincludedontherequestofacustomer.Forthedetailedinformation,please
contactsalesperson.
5.1.PoEcompatibility
WithnonPowerSourcingEquipment(PSE)
WhenitisconnectedwithnonPSE,thepoweradaptorshouldbeconnected.

Withpoweradaptor
ConnectingbothPSEandpoweradaptordoesnotdoanyharmtotheproducts.
Disconnectingpoweradaptorwhileitisoperatingdoesnotstopoperation.Theproduct
continuestoworkwithoutrebooting.

5.2.Powerclassification
ThePoEPowerClasssupportedbyZN‐S100V/ZN‐S1000VEisClass0.Table1showsIEEE
802.3afpowerclasses.

ClassUsageMinimumPowerLevels
OutputatthePSE
MaximumPowerLevelsat
thePoweredDevice
0Default15.4W0.44to12.95W
1Optional4.0W0.44to3.84W
2Optional7.0W3.84to6.49W
3Optional15.4W6.49to12.95W
4ReservedforFutureUseTreatasClass0ReservedforFutureUse
Table1.IEEE802.3afPSEandPoweredDevicePowerClassifications


ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 18
6.Electricalcharacteristics
6.1.Operatingconditions
ParametersMinTypicalMaxUnits
Peaktopeakamplitude 0.2512 V
Syncamplitude72286 572 mV
Horizontallockrange‐ ‐ ±7%oflinelength
Video
inputrange
Colorsub‐carrierLock‐
inrange
‐ ‐ ±800Hz
AudioinputrangeTBD TBDTBDVp‐p
AmbientOperatingTempe rature0‐50ºC
AmbientOperatingHumidityTBD‐TBD %
On‐statecurrent  ‐ ‐ TBD mAD/O
(isolated)OperatingVoltage‐‐TBDVDC
Table2.Operatingconditions
6.2.Powerconsumption
ItemZN‐S100VZN‐S1000VE
InputVoltage12V12V
CurrentTBD TBD
ConsumptionTBD TBD
Table3.Powerconsumption


Overvoltageandovercurrentwillcauseaseveredamagetothedeviceoreven
afire.


ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 19
7.Dimensions

ZN‐S100V




Unit : mm

26.3
94.674.6
106.6 98

ZN-S100V/ZN-S1000VE HARDWARE MANUAL
2010/2-1 D1A.02 20
ZN‐S1000VE

H.264 Network Video Encoder
Status
Data Vin Vout
1CH Encoder
SD
USB
DC12V
Ethernet Reset
DI
2Rx Tx1RS-232
Ain
CRS-485DO
21
Aout
1
1
Unit : mm
103.4
141.4
121.7
37.7