GAPOSA XQ5 User manual

12
1
2
3
Programming Quick Guide
CONNECT POWER TO THE MOTOR
OPTION 1
OPTION 2
PROGRAMMING A TRANSMITTER (Sec. 1)
1Press and hold the SYNC button on the back of the transmitter
or the white button on the head of the motor until the motor
starts moving
2Check the motor rotation (UP or DoWN) then release the SYNC
button or the white button (the motor now stops)
3Within 5 seconds, press the corresponding button (UP if the
motor turns upwards or DoWN if the motor turns downwards.)
This will set the direction of the motor. If the incorrect button is
pressed, the controls will be reversed. To fix, see Sec. 3.
Transmitter is now programmed
ADDING A NEW TRANSMITTER (Sec. 2)
When adding new transmitters, begin with the motor position
somewhere inbetween the two limits. This allows the motor to
have room to move, and allows the direction that the motor moves
to be discernible.
1Press and hold the SYNC button on the back of a transmitter
ALREADY paired until the motor starts moving in one direction
2Check the motor rotation (UP or DoWN) then release the SYNC
button (the motor now stops)
3Within 5 seconds, press the corresponding button (UP if the
motor turns upwards or DoWN if the motor turns downwards)
on the NEW transmitter being added. This will set the direction
of the motor.
Additional transmitter is now added
CHECKING / CHANGING DIRECTION (Sec. 3)
To check the direction, press the UP or DoWN button. The motor
will go UP or DoWN accordingly, if the direction needs to be
changed:
1Press and hold the SYNC button on the back of transmitter until
the motor starts moving
2Press the STOP button; the motor makes a brief jog. The direction
of the motor has been reversed
IMPORTANT: the change of direction procedure must be
performed before initiating the limit setting procedure,
otherwise limits will need to be reset
The buttons shown on the left are used to program the transmitters and specific channels.
The programing button’s (buttons 4 and 5) locations can be placed differently depending
on the transmitter model. Shown in this guide is the Emitto Slim line transmitter.
UP (1) the rolling shade/awning moves up
SToP (2) the rolling shade/awning stops
DoWN (3) the rolling shade/awning moves down
SYNC (4) program the transmitter
LIMIT (5) set limits
1
3
2
5
4
OFF
ON

SETTING THE LIMITS INDIVIDUALLY (Sec. 5)
If the limits need to be changed after the initial limit setting
procedure, it is possible to change the limit positions individually.
One limit can be set without the other limit needing to be set. The
motor can be in any postion to initiate the procedure.
TO CHANGE THE UP LIMIT:
1 From any point between the existing limits, press and hold both
the LIMIT button and the UP button until the motor makes a brief
jog.
Note: during “limit setting mode” the operations are in
“deadman control” (The UP and DoWN buttons must be held
down inorder for the motor to move.)
2 Press and hold the UP button until the desired new UP limit is
reached.
3Press the SToP button to set the limit. The motor makes a brief jog
to confirm. The new UP limit is set.
TO CHANGE THE DoWN LIMIT:
1From any point between the existing limits, press and hold both
the LIMIT button and the DoWN button until the motor makes a
brief jog.
Note: during “limit setting mode” the operations are in
“deadman control” (The UP and DoWN buttons must be held
down inorder for the motor to move.)
2Press and hold the DoWN button until the desired new DoWN
limit is reached
3Press the SToP button to set the limit. The motor makes a brief
jog to confirm. The new DoWN limit is set.
SETTING THE LIMITS (Sec. 4)
IT IS MANDATORY TO SET THE “UP” LIMIT
FIRST EVERY TIME
Run the motor to an intermediate position inbetween the two
desired limits. The motor needs to move in the direction of the
limit in order for the limit to be properly set.
1Press and hold the LIMIT button on the back of transmitter until
the motor makes a brief jog
Note: during “limit setting mode” the operations are in
“deadman control” (The UP and DoWN buttons must be held
down inorder for the motor to move.)
2 Press and hold the UP button and run the motor to the desired
UP limit position.
3Press the SToP button to set the UP limit position. The motor
makes a brief jog to confirm.
4Press and hold the DoWN button and run the motor to the
desired DoWN limit position
5Press the SToP button to set the DoWN limit position.
The motor makes a brief jog to confirm.
Note: Accurate limit setting can be performed by pressing the
LIMIT button a second time: the motor will then will reduce
its output speed, moving slowly in steps towards the desired
limit. Always press the SToP button to set the limit position.
4
5
1
1
2
2
3
3
3
2
1

3”
<15”
ON
OFF
ON
AUTOMATIC SETTING OF THE LIMITS (Sec. 6)
For limits set with torque sensor (mechanical stop of shutters or cassette awnings/
shades), press and hold the UP button until the bottom bar hits the cassette or
shutter box. A short jog will indicate that the UP position has been memorized.
The same procedure can be followed for the DoWN limit but only for roller shutters.
PREFERRED POSITION (Sec. 7)
1. SETTING AN PREFERRED POSITION
Operate the motor to and stop it at the desired intermediate position, then press both the UP
and DoWN buttons together until the motor makes a brief jog to confirm.
The intermediate position is now set.
2. RECALLING THE PREFERRED POSITION
Press and hold the SToP button for 3 seconds: the motor will move to and stop at the
intermediate position.
3. ERASING THE PREFERRED POSITION
Press both the UP and DoWN buttons until the motor makes a brief jog to confirm.
The intermediate position is now erased.
DELETING A TRANSMITTER OR A CHANNEL (Sec. 8)
Using the transmitter to be deleted press and hold both the SYNC and SToP
buttons untill the motor makes a brief jog to confirm.
Only the transmitter used for this procedure has been deleted from motor
memory
RESET TRANSMITTER MEMORY (Sec. 9)
(DELETING ALL THE TRANSMITTERS OR CHANNELS OR
SENSORS)
Option 1 - Using a programmed transmitter
Press and hold both the SYNC and SToP buttons for at least
15 seconds: to confim that the operation has completed, the
motor first makes a brief jog and after 5 seconds it makes an
additional jog. This operation will not be successful unless it
makes both jogs.
Memory is now empty
Option 2 - Using a new transmitter without ID (not
paired).
1 Switch the power to the motor OFF, then switch it back ON.
2Within 8 seconds, using any Gaposa transmitter, press and
hold both the SYNC and SToP buttons until the motor
makes a jog.
Memory is now empty
Option 3 - White button on the head of the motor
Press and hold the white button on the head of the motor
until the motor starts to move. Release the white button.
All transmitters have been erased.
5”
12