Garden Furniture Direct Harrington picnic bench User manual

1
Before you commence the assembly process we recommend that you read these instructions
thoroughly beforehand to familiarise yourself with the assembly process and to also check that you have
the correct components. If for any reason you need assistance, you can find our contact details on the
final page of these instructions.
We highly recommend that any assembly is carried out on a flat, level surface if possible and that you
use another person to assist you if necessary.
Package contents
Tools required
1 x Table Top
2 x Seats
2 x Back Rests
2 x A-frames
2 x Braces
4 x L-shaped Back Rest Supports
40 x 70mm Coach Bolts
64 x Cover Caps
10mm socket or spanner
Harrington picnic bench
GaGarden
rnitu reFuu
Direct
T: 03333 448 121
ASSEMBLY
INSTRUCTIONS
Harrington picnic bench

Harrington Picnic Bench
2
Step 1
Step 2
Ensure that you have all of the correct parts as listed
on the front page of these instructions, including any
fixings.
Lay the table top upside down on a clean, flat surface
taking care not to damage it. Now line up one of the
table A-frames centrally on the table top as shown in
step 3.
Step 3
Step 4
Place one of the table A-frames centrally against the
fixing batten ensuring that the gap at the table edge
is the same on both sides.
Now, using 2 of the supplied coach screws and the
pre drilled holes, secure the table A-frame to the
fixing batten on the table top.

Harrington Picnic Bench
3
Step 5
Step 6
Place a cross brace in position as shown, ensuring
that it is flush with the underside of the table A-frame
and lined up centrally on the table and attach it to
the A-frame with a coach screw.
Make sure that the brace is still aligned centrally on
the table and affix the other end to the table top with
a coach screw as shown. Repeat steps 3 -6 to finish
the table assembly and proceed to step 7.
Step 7
Step 8
Locate the letter on each of the A-frames where the
back rest supports will be located...
...and find the corresponding back rest support. There
will be an A, B,C and D.

Harrington Picnic Bench
4
Step 9
Step 10
Offer up the back rest support to the A-Frame as
shown in the image and attach back rest support
using 2 coach screws, first into the A-frame cross
member...
...and then 2 more into the A-Frame leg.
Step 11
Step 12
Repeat steps 7 - 10 until you have attached all of the
back rest supports as shown above.
Place the seat panels on the A-Frames and ensure
that the back of the seat panel lines up with the
pencil mark on the top of the A-frame cross member.

Harrington Picnic Bench
5
Step 13
Step 14
Once lined up correctly, secure the seat in place using
2 coach screws.
Repeats steps 12 -13 so that both seat panels are
fixed in place as shown.
Step 15
Step 16
Now offer up one the back rest panels and fix into
place with coach screws at both ends of the bench,
ensuring that the top of the back rest panel batten is
flush with the top of the back rest support as shown
in the image. Repeat for the other back panel.
Finally, cover any exposed coach screw heads
with the cover caps provided. Your Harrington
picnic bench set is now complete.
GardenFurniture.Direct i a trading tyle of LTK Sco Limited
Regi tered in England & Wale - Regi tered No. 6282947
We hope that you found your product quick and ea y to a emble.
However, if you require any further a i tance or have any que on you can
contact u by telephone on: 03333 448 121 or vi it www.gardenfurniture.direct