Garden Furniture Direct Newland Picnic Bench User manual

1
Before you commence the assembly process we recommend that you read these instructions thoroughly
beforehand to familiarise yourself with the assembly process and to also check that you have the correct
components. If for any reason you need assistance, you can find our contact details on the final page of
these instructions.
We highly recommend that any assembly is carried out on a flat, level surface if possible and that you
use another person to assist you if necessary.
Package contents
Tools required
1 x Table top
2 x Seats
2 x Table leg frames
2 x Seats
4 x Seat leg frames
1 x Parasol support
2 x A frames
4 x Seat leg braces (not junior version)
2 x Table leg braces (not junior version)
28 x M8 Coach screws 60mm
12 x M8 Coach screws 70mm
40 Cover caps
* 8ft version additionally includes - 2 x seat supports and braces, 8 x
60mm Coach screws and 8 x cover caps.
10mm socket or spanner
GaGarden
Fuurnitu re
Direct
T: 03333 448 121
ASSEMBLY INSTRUCTIONS
Newland picnic bench
Newland Picnic Bench

2
Step 1
Step 2
Ensure that you have all of the correct parts as listed
on the front page of these instructions, including any
fixings.
Lay the table top upside down on a clean, flat
surface taking care not to damage it. Now line up
one of the table leg frames centrally on the table top
as shown in step 3.
Step 3
Step 4
Place one of the table leg frames centrally against
the fixing batten ensuring that the gap at the table
edge is the same on both sides. Now, using 2 of the
supplied 70mm coach screws and the pre drilled
holes, secure the table leg frame to the fixing batten
on the table top.
Using one of the supplied 70mm coach screws and
the pre drilled holes, secure the table leg frame to
the fixing batten on the table top...
Newland picnic bench

3
Step 5
Step 6
...and secure the other side in the same fashion.
Repeat steps 2-5 for the other table leg frame.
Now both ends are attached....
Step 7
Step 8
...turn the table right side up.
Place one of the leg braces centrally against table leg
frame as shown and proceed to step 9.
Newland picnic bench

4
Step 9
Step 10
Using the pencil lines on the leg brace as a guide,
line up the brace in the correct position and attach it
to the bottom of the table leg frame...
...using a 60mm coach screw. Then secure the other
end of the brace in the same manner.
Step 11
Step 12
Now repeat steps 8 - 10 for the other end of the
table until your table is as shown above.
Insert the parasol brace into the gap between the
table legs until each end is resting on the table leg
frame cross brace, as shown above.
Newland picnic bench

5
Step 13
Step 14
Ensure the end of the parasol brace is flush with the
end frame.
Then secure in place using 2 x 60mm coach screws in
each end of the parasol brace. (For the
junior/children's version proceed to Step 18)
Step 15
Step 16
Position one of the table leg braces so that it is
positioned as shown and also central across the
parasol brace then hold it in place. (Omit this step
and the next two for the junior version).
Now look under the table and adjust the position so
that this is also aligned centrally across the table
centre slat.
Newland picnic bench

6
Step 17
Step 18
Continue to hold the table leg brace firmly in place
and attach it to both the parasol brace and table top
using 60mm coach screws. Repeat the process for
the other angle brace.
Now lay one of the seat panels upside down on a flat
surface as shown.
Step 19
Step 20
Align one of the seat leg frames centrally across the
seat panel.
Attach the leg frame using 2 x 70mm coach screws
as shown. Repeat for the other end of the seat panel
then for the remaining seat panel and leg frames.
(For the junior/children's version proceed to Step 28)
Newland picnic bench

7
Step 21
Step 22
Place a seat leg brace in position and, as you did for
the table, ensure it is centrally aligned. (Omit this
step and the next two for the junior version).
Now attach it to the seat panel and seat end frame
using 60mm coach screws.
Step 23
Step 24
Attach one of the seat leg braces to the other end of
the seat unit and then repeat steps 19-21 for the
other seat.
For an 8ft model, follow Steps 24 to 27. Place one of
the seat panels upside on a flat surface and place the
seat support adjacent to the centre batten...
Newland picnic bench

8
Step 25
Step 26
...and aligned centrally on the seat panel before
fixing into place with 2 x 60mm coach screws as
shown.
Now place the brace set support brace as shown so
that it is also aligned centrally...
Step 27
Step 28
...before fixing into place with a 60mm coach
through the brace into both the support and the
underside of the seat panel.
Place the completed seat units in position, ready to
be secured to the main table assembly as shown.
Newland picnic bench

9
Step 29
Step 30
Ensure that the edge of the seat frame is flush with
the end of the leg brace...
... and fix into place using 2 x 60mm coach screws.
Repeat this for the remaining 3 seat frame ends.
Step 31
Place the black cover caps supplied over any exposed
screw heads. Your bench is now complete.
Newland picnic bench
GardenFurniture.Direct i a trading tyle of LTK Sco Limited
Regi tered in England & Wale - Regi tered No. 6282947
We hope that you found your product quick and ea y to a emble.
However, if you require any further a i tance or have any que on you can
contact u by telephone on: 03333 448 121 or vi it www.gardenfurniture.direct