Garden Furniture Direct LANGDALE PICNIC BENCH User manual

1
Before you commence the assembly process we recommend that you read these instructions
thoroughly beforehand to familiarise yourself with the assembly process and to also check that you have
the correct components. If for any reason you need assistance, you can find our contact details on the
final page of these instructions.
We highly recommend that any assembly is carried out on a flat, level surface if possible and that you
use another person to assist you if necessary.
Tools required
Package contents
1 x Table top
2 x Seats
2 x Table A-frames
2 x Cross braces
2 x Seat supports and braces (8ft version)
16 x M8 Coach screws
Cover caps
10mm socket or spanner
The Langdale picnic bench
GaGarden
rnitu reFuu
Direct
T: 03333 448 121
ASSEMBLY INSTRUCTIONS
Langdale picnic bench

Langdale picnic bench
2
Step 1
Step 2
Ensure that you have all of the correct parts as listed
on the front page of these instructions, including any
fixings.
Lay the table top upside down on a clean, flat surface
taking care not to damage it. Now line up one of the
table A-frames centrally on the table top as shown in
step 3.
Step 3
Step 4
Place one of the table A-frames centrally against the
fixing batten ensuring that the gap at the table edge
is the same on both sides. Now, using 2 of the
supplied coach screws and the pre drilled holes,
secure the table A-frame to the fixing batten on the
table top.
Place a cross brace in position as shown, ensuring
that it is flush with the underside of the table A-frame
and proceed to step 5. If you are building the 3ft
version please refer to Step 8 before proceeding with
Step 5.

Langdale picnic bench
3
Step 5
Step 6
Ensure that the brace is lined up centrally on the
table and attach it to the A-frame with a coach screw.
Make sure that the brace is still aligned centrally on
the table and affix the other end to the table top with
a coach screw as shown. Repeat steps 3 -6 to finish
the table assembly and proceed to step 8.
Step 7
Step 8
For the 3ft version steps 4 - 7 should be carried out
but with the braces in an offset configuration as
shown above and not centred on the table top.
Now proceed with Step 5.
Turn the table assembly right side up in preparation
for attaching the seat panels.

LANGDALE picnic bench
4
Step 9
Step 10
For an 8ft model, follow Steps 9 to 12. Place one of
the seat panels upside on a flat surface and place the
seat support adjacent to the centre batten...
...and aligned centrally on the seat panel before fixing
into place with 2 x 60mm coach screws as shown.
Step 11
Step 12
Now place the brace set support brace as shown
so that it is also aligned centrally...
...before fixing into place with a 60mm coach through
the brace into both the support and the underside of
the seat panel.

Langdale picnic bench
5
Step 9
Step 10
Place one of the seat panels in position as shown as
and proceed to step 10.
Align the seat panel batten with the outer end of the
A-frame as shown and repeat for the other end of the
seat panel.
Step 11
Step 12
Using the coach screws provided attach the seat
panel to the A-frame at both ends of the bench.
Please note that the children's version will have only
one screw at either end.
Repeat steps 9-11 for the other seat panel.
Finally, cover any exposed coach screw heads with
the cover caps provided. Your Langdale picnic bench
is now complete.
GardenFurniture.Direct i a trading tyle of LTK Sco Limited
Regi tered in England & Wale - Regi tered No. 6282947
We hope that you found your product quick and ea y to a emble.
However, if you require any further a i tance or have any que on you can
contact u by telephone on: 03333 448 121 or vi it www.gardenfurniture.direct