Garmin GPSMAP 5008 - Marine GPS Receiver Configuration guide

Printing agPSMaP®4000/5000 SerieS FluSh Mount teMPlate in adobe acrobat
Notes:
(A) Youmustprintthetemplateon11˝x17˝paper.Thisisnormallyselectedinthe‘PrinterProperties’,andwilldifferbymanufacturer.
• Ifyourprinterisnotcapableofprintingon11˝x17˝paper,oryoudonothave11˝x17˝paper,youmustprintthistemplateatanoffice
servicesstoreorsimilarlocationthathastheabilitytoprinton11˝x17˝paper.
(B) Youmustsetthe‘PageScaling’settingto‘None’.
(C)Select‘Auto-RotateandCenter’tomakesurethetemplateprintsinthecorrectorientation.
Important Information:
• Beforecuttingthemountingsurface,measuretheprintouttomakesureitprintedatthecorrectsize.Boththelengthandwidth
measurementsarenotedonthetemplate.Verify both the length and width measurements before cutting.
• WhencuttingtheFlushMounttemplate,cutinside the line,thensandand/orlethemountingsurfacetoensureagoodt.
A
B
C
Adobe Acrobat Print Dialog Box
Printing a Flush Mount Template.1 1 3/23/2007 4:58:23 PM

August 2007 190-00803-03 Rev. C Printed in Taiwan
GPSMAP®5008/5208 FLUSH MOUNT TEMPLATE
6 9/16"
(166.1 mm)
8 7/32" (208.9 mm)
Unit Dimensions: 10 1/8" (256.9 mm) W x 7" (176.9 mm) H
1/2"
13 mm
USE 4 mm DRILL BIT
Recommended clearance for
SD card door
UTILISATION d’un FORET de 4 mm
UTILIZZARE UNA PUNTA DA
TRAPANO DA 4 mm
Verwenden Sie einen 4 mm-Bohrer
UTILICE UNA BROCA DE 4 mm
BRUG ET 4 mm BOREHOVED
BRUK EN 4 mm BIT
ANVÄND EN 4 mm BORRSPETS
Débattement recommandé pour
le cache de la carte SD
Spazio libero consigliato per lo
sportello della scheda SD
Empfohlener Abstand für SD-
Speicherkartenabdeckung
Se recomienda despejar la puerta
de la tarjeta SD
Rekommenderat utrymme för
SD-kortlucka
Anbefalet fri plads til SD-kortlåg
Anbefalt klaring for SD-kortdekselet
Pilot Hole
3
/
8
" (9.5 mm)
Trou d’implantation
9,5 mm
Foro guida
9,5 mm (
3
/
8
”)
Vorbohrung
9,5 mm (
3
/
8
”)
Oricio guía
9,5 mm (
3
/
8
pulg.)
Forboring
9,5 mm (
3
/
8
”)
Styrehull
9,5 mm
Rikthål
9,5 mm (
3
/
8
tum)
Dimensions de l’appareil : 256,9 mm x 176,9 mm (l x H)
Dimensioni unità: L 256,9 mm x A 176,9 mm
Geräteabmessungen: Breite 256,9 mm x Höhe 176,9 mm
Dimensiones de la unidad: 256,9 mm ancho x 176,9 mm alto
Enhetsmått: 256,9mm B x 176,9mm H
Enhedens mål: 256,9 mm B x 176,9 mm H
Mål på enheten: 256,9 mm B x 176,9 mm H
CUT ON THIS LINE
DECOUPEZ EN SUIVANT CETTE LIGNE
TAGLIARE SEGUENDO QUESTA LINEA
SCHNEIDEN SIE ENTLANG DIESER LINIE
CORTE EN ESTA LÍNEA
SKÆR PÅ DENNE LINJE
SKJÆR LANGSDENNESTREKEN
SÅGA LÄNGS MED DEN HÄR LINJEN