Garmin 600 T-TOP User manual

600 T-TOP
INSTALLATION GUIDE
Please take a few minutes to read the enre installaon instrucons before installaon.

PART LIST
Canopy Frame
Front stbd 1x Front port 1x
Rear stbd 1x Rear port1x Centre Plate 1x
Accy Plate 1x
Side Frame Lower
Port
1x
Port
1x
Port
1x
Stbd
1x
Stbd
1x
Stbd
1x

Side Upper Frame
Port 1x Stbd 1x
Other Parts
1x
1/2 Inch
28x
1/4 Inch
28x
CANVAS
1x 1x Rope 1x
1/4 Inch
12x
1/4 Inch
12x
1/4 Inch
12x

STEP 1
Before Install
Layout all the parts so that you know which piece
goes where.
A helper is needed for installaon.
The two main components are the side legs and
the canopy frame.The side legs are mirror images
to provide right and le legs.These are hinged in
the center to allow the T-Top to be folded
forward.The legs are typically mounted with the
bolt heads to the outside for folding the T-Top
down. The canopy frame has four secons.The
two front secons aach to the legs by the upper
leg clamps.The canopy frame hinge allows the
canopy frame to fold for storage.
You should protect the parts from scratches by
doing the assembly on a tarp or cardboard.
Apply a grease to the bolts before screw in.
ASSEMBLE THE LOWER SIDE SECTIONS
PORTSTBD

STEP 2
MEASUREMENTS FROM THE SIDES AND AFT OF THE BOAT.
IMPORTANT NOTE:
SO IT IS VERY IMPORTANT TO CONSIDER THEIR PLACEMENT NOW BEFORE CONTINUING TO THE NEXT
STEP OF THE PROCESS.
RECOMMENDED DISTANCE FROM CONSOLE
RECOMMENDED MOUNTING AREA

USE AMARKER TO MARK OUT WHERE THE FEET ARE
POSITIONED.
NOTE: MAKE SURE THAT THE MARKER IS USED ON
THE MASKING TAPE AND DOES NOT MARK UP THE
DECK.
ASSEMBLE THE SIDE SECTIONS
STEP 3
STEP 4
PORT & STARBOARD SIDES
THREADLOCKER

STEP 5
STEP 6
MEASURE THE WIDTH OF YOUR MARKED
MOUNTING LOCATIONS. THIS WIDTH WILL
SIDES TO THE CANOPY.
ASSEMBLE THE FRONT TOP SECTION.
FIRST ASSEMLE THE PORT SIDE TO THE STARBOARD SIDE.
THEN ASSEMBLE THE ACCESSORY PLATE AND THE MIDDLE PLATE.

STEP 7
STEP 8
MEASURE WIDTH OF SIDES
TO MATCH THE MOUNTING
POSITION WIDTH
NOTE: ASSEMBLE THE CANOPY TO THE SIDE SECTION WHILE ON LAND.
THE ASSEMBLY WILL THEN BE WALKED ONTO THE BOAT AND PLACED
IN THE MARKED LOCATION.
ATTACH FRONT HALF OF CANOPY
THREADLOCKER
ASSEMBLE THE REAR CANOPY FRAME
FIRST ASSEMLE THE PORT SIDE TO THE STARBOARD SIDE.
THEN ASSEMBLE THE ACCESSORY PLATE AND THE MIDDLE PLATE.
DO NOT JOINT THE FRONT TO THE REAR YET

STEP 9
CONCOLE. POSITION THE MOUNTING
FEET OVER THE MARKED LOCATIONS.
MARKED LOCATIONS
LOWER INTO POSITION
POSITION MOUNTING FEET
OVER MARKED LOCATIONS

Gelcoat
Fibreglass
A
C
B
STEP 10
DRILL PILOT HOLE WITH A SMALL DRILL BIT
LOCATION AND DRILL A LARGER HOLE
FOR THE MOUNTING HARDWARE.
COUNTERSINK THE GELCOAT TO PREVENT
STRESS CRACKING DURING INSTALLATION.

D
E
F
STEP 10
REMOVE MASKING TAPE.
APPLY MARINE GRADE SEALANT.
WE RECOMEND: 3M 5200 MARINE
ADHESIVE OR EQUIVALENT.
THE SEALANT AND LOWER INTO
PLACE.
INSTALL SCREWS AND TIGHTLY FASTEN
THE MOUNTING FEET TO THE DECK OF
THE BOAT.
REMOVE EXCESS SEALANT FROM
AROUND THE MOUNTING FOOT.

STEP 11
STEP 12
canvas
MOUNT AFT SECTION OF CANOPY
THREADLOCKER

STEP 13
A
C
B
D
STEP 14
TIE A KNOT IN EACH END TO
START AND STOP THE CORD.
USE ZIP TIES TO FASTEN THE
CANOPY IN PLACE BEFORE
LACING IT TO THE FRAME.
TIP: USE THE ZIP TIES IN THE
CORNERS TO CREATE TENSION
IN THE CANOPY.
CANVAS