Gasmate AH1069ODS User manual

03531 12/16
Important: Retain these instructions for future use.
FOR YOUR SAFETY
If you smell gas:
1. Shut off the gas to the appliance.
2. Extinguish any open flame.
3. If odour continues, immediately call your gas supplier.
Do not store or use gasoline or other flammable vapour
and liquids in the vicinity of this or any other appliance.
WARNING
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
Read the instructions thoroughly before installing or
servicing this equipment.
FOR OUTDOOR USE ONLY
PROPANE GAS
Model No. AH1069ODS, AH1060ODS
The ideal solution for extending the season of
outdoor entertaining
Creates a stylish and attractive ambience
Direct ignition
Includes a safety ‘tip-over’ switch that halts supply of
gas to the unit should it be accidently knocked over
Oxygen depletion system for enhanced safety
Stainless steel burner for extra long-term reliability
Complete with hose and POL regulator
Efficient and powerful 27.5MJ/h output
Adjustable heat output
Operates for approximately 17 hours on a properly
filled 9Kg Propane cylinder
For outdoor use only
Gas certified to Australian standards

2
Installation, Operation and Maintenance Instructions
INSTALLATION
3. Proper clearance from combustible materials must
be maintained at all times. The minimum clearances
are as follows:
Minimum Clearance from Combustibles:
Side 500 mm Rear 500 mm
Ceiling 1000 mm
Combustible materials are considered to be wood,
compressed paper, plant fibres, plastic,
plexiglas or other materials capable of being ignited and
burned.
Such materials shall be considered combustible even
though flame proofed, fire-retardant treated or plastered.
Additional clearance may be required for glass, painted
surfaces and other materials which may be damaged by
radiant or convection heat.
4. Heaters must be placed on a level and adequate
footing and be readily accessible.
5. The gas manifold supply pressure must be regulated
at 2.75 kPa utilising an AGA approved regulator
(supplied with heater).
6. The appliance must be inspected before each use,
and at least annually by a qualified service person.
a. The appliance area must be kept clear and free
of combustible materials, gasoline and other
flammable vapours and liquids.
b. Gas orifices and burner must be kept clear of dirt
and cobwebs. Flow of combustion and ventilation
air through the perforated portions of the heater
must not be obstructed. Cleaning with a soft
brush before use and at least every six months is
recommended.
c. All gas connections should be checked for
leaks utilising a soap solution. Never use a flame for
this purpose.
d. The flame pattern should be visually checked
whenever heater is operated. If flames extend
beyond surface of the guard the appliance should
be turned off and should not be operated again until
the unit is serviced and or repaired.
e. Any cleaning agent used on the heater should be of
a non-combustible and non-corrosive nature.
f. The stainless steel emitter normally does not require
cleaning and should NEVER be painted.
Important Safety Rules
This appliance must only be used in a well
ventilated area.
1. This appliance shall not be installed or used
indoors, in buildings, garages or any other
enclosed area.
2. DO NOT place articles on or against this
appliance.
3. DO NOT use or store flammable materials near
this appliance.
4. Children and adults should be alerted to the
hazards of high surface temperatures, burns
and clothing ignition.
5. Children should be carefully supervised when
they are in the area of the appliance.
6. NEVER hang anything including clothes or
other flammable items on the appliance.
7. DO NOT operate this appliance unless it is
fully assembled with burner guard in place.
8. DO NOT SPRAY AEROSOLS IN THE
VICINITY OF THIS APPLIANCE WHILE IT IS
IN OPERATION.
9. Installation and repair should be done by a
qualified service person. The appliance must
be inspected before use and at least annually
by a qualified service person. It is imperative
that control compartment, burners and
circulating air passages of the heater be kept
clean.
Prior to assembling your appliance, the following must
be reviewed. Compliance with the following should result
in satisfactory heater operation. This instruction manual
should be retained for future reference. The installation
must conform with local codes or authority having
jurisdiction.
1. The patio heater is intended for heating residential
and non-residential outdoor spaces. The installation
must conform with local codes and with the
Australian Standard AS/NZS 5601.
2. Adequate clearance around air openings into the
combustion chamber, clearances from combustible
materials, provisions for accessibility and for
combustion and ventilating air supply must be
maintained at all times when the appliance is
operating.

3
Installation, Operation and Maintenance Instructions
7. The hose must be protected from contact with
hot or sharp surfaces both during use and while
in storage. The hose assembly should be visually
inspected prior to each use of the heater. If
excessive abrasion or wear is evident, or the hose
is cut, it must be replaced prior to operating the
heater. The replacement hose assembly may be
obtained from the manufacturer.
8. DO NOT use any pressure regulator or hose
assembly other than those supplied with the
appliance. Replacement pressure regulator
and hose assembly must be those specified.
Replacement parts maybe obtained from the
manufacturer or your local sales
representative.
9. Installation and use of this heater must conform with
local codes and AS/NZS 5601.
10. This heater is designed to operate with a standard
9Kg propane cylinder with Approved Cylinder
Connection.
11. The valve outlet must be maintained in good
condition. When the cylinder is not in use, be sure
to cover it with a dust cap. A leak test should be
performed with soapy water whenever connecting a
new cylinder. NEVER use a match to test for leaks.
12. The propane cylinder must be turned off whenever
the heater is not in use. When the heater is to be
stored indoors, the propane cylinder and the heater
must be disconnected and the cylinder stored in
accordance with the Standard for Storage and
Handling of Liquefied Gases.
13. The appliance has been designed with several
safety features which include a tip over switch.
IMPORTANT
Storage of an appliance indoors with the cylinder
attached is only permitted if the size of the cylinder
complies with AS/NZS 1596; otherwise cylinders
must be stored outdoors in a well ventilated area.
The guards are fitted to this appliance to reduce the
risk of fire or injury from burns and no part of it should
be removed.
This appliance must be protected from exposure to
rain.
Any modification to the heater not described in the
installation instructions may compromise the safety of
this appliance. Special concern is as follows:
(1) DO NOT bypass thermocouple safety burner;
(2) DO NOT operate heater without the guard;
Clothing or other flammable materials should not be
hung from the heater, or placed on or near the heater.
The area above the burner may be extremely hot. Direct
contact with these metal surfaces should be avoided in
order to prevent burns or clothing ignition.
Screw the coupling nut of regulator into the cylinder valve
outlet.
POL CYLINDER CONNECTION DEVICE
Type of Gas Propane
Consumption 27.5 MJ/h
Operating Pressure 2.75 kPa
Injector Size 1.48 mm
Heater specifications can be found on the data label.

4
Tools Required
Phillips head screwdriver, 2 Adjustable spanners
Note: Remove any transit protection material
STEP 1
Attach the brackets onto the base with four M8 x 16mm
bolts, then attach the cylinder cover with eight M5 x 10mm
screws and nuts.
STEP 2
Place the burner head on the cylinder cover and secure
with four M4 x 8mm screws.
STEP 3
Position the mesh guard around the burner with the lift up
door in front of the control knob locating the wire pins into
the cylinder cover holes then secure with the wing nut on
top.
STEP 4
Attach the hose and regulator to the underside of the
burner head, tightening the hose fitting thread firmly. Leak
test this connection with a soapy water solution before
attempting to light the heater.
AREA HEATER ASSEMBLY
BRACKETS
BASE
WING NUT
BURNER HEAD
CYLINDER
COVER
HOSE AND
REGULATOR
MESH GUARD
PARTS LIST
NAME QTY
Mesh Guard 2
Burner Head 1
Cylinder Cover 1
Hose and Regulator 1
Base 1
Base Brackets 4
Wing Nut 1
M8 x 16mm Bolt 6
M8 Nut 2
M5 x 10mm Screws & Nuts 8
M4 x 8mm Screws 4

5
AREA HEATER - For Outdoor Use Only
Minimum Clearance from Combustible Surfaces*:
*Combustible materials are considered to be wood, compressed paper, plant fibres,
plastic or other materials that are capable of being ignited and burned.
500mm
1400mm
850mm
450mm
1000mm