GE PGP976DET2BB User manual

Istollotio
Istructio s 36" SealedGasCooktop
PGP976, PGP986, CGP650
j r_l Questions? call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca i
IN THE COMMONWEALTH OF
MASSACH USETTS:
, This product must be installed by a licensed
plumber or gas fitter.
, When using ball-type gas shut-off valves, they
shall be the T-handle type.
, A flexible gas connector, when used, must not
exceed 3 feet.
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
.IMPORTANT - Savetheseinstructions
for local inspector's use.
, IMPORTANT - ObserveaUgoverning
codes and ordinances.
, Note to Installer- Be sure to leave these
instructions with the Consumer.
Note to Consumer - Keep these instructions for
future reference.
, Product failure due to improper installation is not
covered under the Warranty.
,AWARNING - This appliancemust be
properly grounded.
.IMPORTANT -Leak testingofthe
applianceshallbe conducted accordingto the
manufacturer's instructions.
, Proper installation is the responsibility of the
installer and product failure due to improper
installation is NOT covered under warranty.
WARN ING - Disconnectallelectrical
power at the main circuit breaker
or fuse box before installing.
FOR YOUR SAFETY:
_I,WARNING - iftheinformationinthis
manual is not followed exactly, mfire, explosion
or gas leak may result causing property damage,
personal injury or death.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance!
Do not install this product with an air curtain
hood or other range hood that operates by
blowing air down on the cooktop. This airflow
may interfere with operation of the gas burners
resulting in fire or explosion hazard.
WHAT TO DO IF YOU SMELL
GAS:
, Do not try to light any appliance. Do not touch
any electrical switch; do not use any phone in
your building.
immediately coil your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
, If you cannot reach your gas supplier, coil the
fire deportment.
installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
This cooktop has been certified by UL. You'll find
safety precautions in your Owner's Manual. Read
them carefully.
Installation of this cooktop must conform with
local codes or in the absence of local codes with
the National Fuel Gas Code, ANSI Z223.Z/NFPA
54-Latest edition.
Be sure your cooktop is installed properly by a
qualified installer or service technician.
To eliminate reaching over surface burners,
cabinet storage above burner should be avoided.
Do not install the unit near an outside door or
where a draft may affect its use.
31-i0955 ii-13 GE i

Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the proper
voltage and frequency and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or fuse having
amperage as noted on the rating plate.
We recommend you have the electrical wiring and
hookup of your cooktop connected by a qualified
electrician. After installation, have the electrician
show you where your main cooktop disconnect is
located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your
cooktop according to governing codes could result
in a hazardous condition.
If there are no codes, your cooktop must be wired
and fused to meet the requirements
of the National Electrical Code, ANSI/NFPA No. 70--
Latest edition. You can get a copy
by writing:
National Fire Protection Association
Batterymarch Park
Quincy, P1A 02269
In Canada your cooktop must be wired and fused
to meet the requirements of the Canadian Electrical
Code.
Be sure the installation of this product in a mobile
home conforms with the Manufactured Home
Construction and Safety Standard, Title 24 CFR,
Part 3280. If this standard does not apply, you
must follow the standard for Manufactured Home
Installations, ANSI/NCSBS A225.1 or with local
codes where applicable.
You can get a copy of the Federal Standard by
Writing:
Office of Mobile Home Standards
HUD Building
451 7th Street, S.W.
Washington, D.C. 24010
PARTS INCLUDED
2Screws Regulator
2 Hold
Down Brackets
MATERIALS YOU MAY NEED
Joint Sealant Pipe Fittings Shut-Off Valve
CSA-Approved Flexible Gas Line
3/8" Min. ID, 1/2" NPTConnection,
3-foot Maximum Length (Massachusetts Only)
TOOLS YOU WILL NEED
FOR INSTALLATION
Pencil
Phillips-Head
Screwdriver
Ruler or Straightedge
Safety Glasses
Saber Saw
Pipe Wrench
!/8" Drill Bit & Electric or
Hand Drill

Installation Instructions
PRE-INSTALLATION CHECKLIST
[Z]
@
When preparing cooktop opening, make
sure the inside of the cabinet and the
cooktop do not interfere with each other.
(See section on preparing the opening.)
Remove packaging materials, grote boxes,
regulator with literature, and literature
package from the cooktop before beginning
installation.
i/
/i/
Foam
Pac_,_,_///_,_r,_/,_ _ _ _ _
Cooktop J
Package
Grate boxes
E1 Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature (Owners Manual,
Installation Instructions, etc.)in a safe place
for future reference.
El
El
FF1
[]
Make sure you have all the tools and
materials you need before starting the
installation of the cooktop.
Your home must provide the adequate
electrical service needed to safely and
properly use your cooktop. (Refer to section
on electrical requirements.)
When installing your cooktop in your home,
make sure all local codes and ordinances
are followed exactly as stated.
Make sure the wall coverings, countertop
and cabinets around the cooktop can
withstand heat (up to 200°F) generated by
the cooktop.

Installation Instructions
PREPARING THE OPENING
MAINTAIN THE FOLLOWING
MINIMUM CLEARANCE DIMENSIONS
23" MAX. De R - IVllN. clearance
of unprotected from cutout to right
overhead side wall
cabinets
I
]0" MIN. clearance from
countertop to unprotected
overhead surface
C- MIN. I
clearance from I
cutout to rear
wall
L - MIN. clearance
from cooktop to left
side wall ]0" or wider
cabinetbase
18" MIN. height
countertop
to nearest
cabinet on either
side of unit
2-1/2" MIN from cutout to
front of countertop
ALL HORIZONTAL
CLEARANCES MUST
BE MAINTAINED FOR PGP976
A MINIMUM OF18" PGP986
ABOVETHECOOKING CGP650
SURFACE,
NOTE: Allow 7/16" minimum _,-2"
vertical clearance from s 11/16 €
the cooktop bottom (or 3_
L
3-3/a,"
12"
12"
R C
6" 3-3/8"
12" 3-3/8"
12" 3-3/8"
7/16"
DRAWERI_
3-11/16" minimum depth
from the countertop) to any
combustible surfaces, such as
a cabinet drawer.
For island installation, maintain
2-1/2 in. minimum from cutout to
front and back edge of countertop. Maintain 3 in.
minimum from cutout to side edges of countertop.
E_ OVERALL COOKTOP DIMENSIONS
3-1/4"
18-7/8" _
F_ CUTOUT DIMENSIONS OF COUNTERTOP
To ensure accuracy, it is best to make a template
when cutting the opening in the counter,
19-1/8" width cut
RECOMMENDED GAS SUPPLY
LOCATION FROM BACKWALL
Recommended
gas supply
location
1" Min. From Backwall
From Cutout
Center Line
r_ MAKE SUREWALL COVERINGS,
COUNTERTOP AND CABINETS
AROUND COOKTOP CAN WITHSTAND
HEAT (UPTO 200°FI GENERATED BY
COOKTOP
countertop must l
withstand heat I
[]_] FOR AMERICANS WITH DISABILITIES
ACT (ADA} FORWARD APPROACH
INSTALLATION ON LY:
Allow 5" minimum I
depth between the I
countertop and an I
I
enclosure. _
I
I
I
U
NOTE: The enclosure must be made of wood
material. Also, an access panel is required for the
electrical outlet, pressure regulator, shut-off valve,
hold-down brackets, and service.

Installation Instructions
iNSTALLiNG THE COOKTOP UNiT
rT]LOCATE ELECTRICAL OUTLET AND
GAS SHUT-OFF VALVE BENEATH
CABINET
NEVER REUSE OLD
CONNECTORS WHEN
INSTALLING THIS
UNIT.
i
I_ 7f
_1 LJ
II
ShutOff _,H IF''
_Valve --_ j ElectricalOutlet 12"
Below
Countertop
Install a manual shut-off valve in the gas line in an
easily accessible location outside the cooktop. Be
sure you know how and where to shut off the gas
supply to the cooktop. Install the electrical outlet
12" below the countertop.
[_] PROTECT SURFACE OF COOKTOP
Place a towel or tablecloth onto the countertop.
Lay the cooktop upside down onto the protected
surface.
Bottom of cooktop j
Cloth under Cooktop
r_ LOCATE MOUNTING PARTS
Remove the hold down brackets from the literature
package.
ATTACH BRACKETS TO COOKTOP
Remove the screw from the side of the cooktop
and screw the hold-down bracket to the side of the
cooktop unit. Repeat for opposite side of cooktop.
Pre-drilled
Bottom of hole
Cooktop \
Cookto
Surface
r_ INSERT COOKTOP INTO CUTOUT
Insert the cooktop centered into the cutout opening.
Hake sure the front edge of the countertop is
parallel to the cooktop. Hake final check that all
required clearances are met.
Once the unit is in place, screw the
hold- down bracket into the cabinet sides
to secure the unit into place.

Installation Instructions
INSTALLATION--GAS CONNECTIONS
r_ PROVIDE ADEQUATE
GAS SUPPLY
This cooktop is designed to operate on natural
gas at 5" of water column manifold pressure and
7" of water column (W.C.) supply pressure. It is
shipped from the factory set for natural gas. The
convertible pressure regulator supplied with the
unit must be connected in series with the manifold
of the cooktop and must remain in series with the
supply line regardless of whether natural or L.P.
gas is being used. FOR PROPEROPERATION, THE
MAXIMUM INLET PRESSURETO THE REGULATOR
MUST BE NO MORE THAN 14" OF WATER COLUMN
PRESSURE.For checking the regulator, the inlet
pressure must be at least 1" W.C.. (or 3.4 KPA)
greater than the regulator output setting. If
the regulator is set for 5" W.C. of water column
pressure, the inlet pressure must be at least 6" W.C.
If the regulator is set for 10" W.C., the inlet pressure
must be at least 11" W.C.. The gas supply line to
the cooktop should be 1/2" or 3/4" pipe.
_] INSTALL REGULATOR
NEVER REUSEOLD CONNECTORS WHEN
INSTALLING THIS COOKTOP.
, WARNING: Never reuse old flexible
connectors.The use ofoldflexibleconnectors
can cause gas leaksand personalinjury.Always
use new flexibleconnectorswhen installinga gas
appliance.
Screw a section of pipe onto
the inlet end of the pressure
regulator and install the
coupling.
Pressure __-]
Regulator 'U]]J
Coupling _
To reduce the likelihood of gas leaks, apply teflon
tape or a thread compound approved for use with
LP or Natural gases to all threaded connections.
r_ INSTALL REGULATOR ONTO
BURNER BOX BOTTOM
Screw the regulator
onto the burner
box bottom pipe
connection. Make
sure the top of
the regulator is
facing towards the
cabinet front, easily
accessible through
the cabinet doors.
The regulator may
also be installed
prior to inserting
Pressure 41
Regulotor-----_l
Coupling l LI
', Electrical
II Outlet 12"
I Below
Countertop
the cooktop into the cutout if extreme caution is
used to ensure the regulator connection is not
compromised.
COMPLETE CONNECTION WITH A
COUPLING
Complete the
connection between
the regulator, pipe
coupling, and
the shut-off valve. Pressure
Regulator
Coupling
Shut-Off _1
Valve
I
II
II Electrical
I Outlet 12"
I Below
Countertop

Installation Instructions
CHECK FOR LEAKS
LEAKTESTING OF THE APPLIANCE SHALL BE
CONDUCTED ACCORDING TO THE MANUFACTURER'S
INSTRUCTIONS.
Before testing for leaks, make sure all burner knobs
are in the OFF position.
After connecting the cooktop to gas, check system
for leaks with a manometer. If a manometer is not
available, turn the gas supply on to the cooktop
and use a liquid leak detector at all joints and
connections to check for leaks.
Tighten all connections if necessary to prevent gas
leakage in the cooktop or supply line.
DO NOT USE OPEN FLAME TO CHECK FOR
LEAKS!
Disconnect the cooktop and its individual shut-off
valve from the gas supply piping system during any
pressure testing of that system at test pressures
greater than 1/2 psig (3.5 kPa).
Isolate the cooktop from the gas supply piping
system by closing its individual shut-off valve
during any pressure testing of the gas supply
system at test pressures equal to or less than 1/2
psig (3.5 kPa).
[_] INSTALLATION OVER BUILT-IN
OVEN
See built-in oven installation for complete
installation instructions.
90 ° Elbow
1
5" To Center of
2" Dia. Hole From
Countertop
2" Dia. Hole
(20 7/8" from front
of Countertop to
Hole Center)
Cabinet Sides __ .J_"
View from Front of Cooktop

Instelletion Instructions
INSTALLATION--ELECTRICAL CONNECTIONS
, WARNING - Disconnect all electrical
power at the main circuit breaker or fuse box
before installing.
ELECTRICAL SUPPLY AND OUTLET
An adequate electrical supply and outlet must
be used to operate the electrical parts of your
cooktop.
[]
D
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which must
be used with a properly grounded 3-hole
outlet with a standard 120 Volt, 60 cycle AC
household current.
If you do not have a 3-hole grounded outlet,
have a qualified electrician change your old
one. DO NOT, UNDER ANY CIRCUMSTANCES,
CUT OR REMOVE THE THIRD (GROUND) PRONG
FROM THE POWER CORD. DO NOT USE AN
ADAPTER. DO NOT USE AN EXTENSION CORD.
Insure proper
L ground and
firm connection
before use

Installation Instructions
COOKTOP BURNERS
ASSEMBLING THE COOKTOP BURNERS
The electrode of the igniter is exposed. Be careful not to turn on any cooktop controls
while the top of the burner is removed. Do not remove the top or touch the electrode
of any burner while another burner is turned on. Electrical shock might result.
[] Place the burner head onto the burner base. Hake sure to place the correct
burner head on the correct burner base and that the burner head sits level on
the burner base. The burner heads are not interchangeable. Ensure the slot in
the burner head is positioned over the electrode and that the burner head is
fully inserted inside the burner base. A small gap between the base and head is
normal.
[]
J
Burner cap properly seated
Place the burner caps on the burner heads, making sure to place the correct
burner cap on the correct burner head. The burner caps are not Burner cap not properly seated
interchangeable. Each cap has three to four pins. Hake sure that the burner
caps are properly seated on the burner heads and that none of the pins sit in the stability chamber.
chamber -_ Electrode
OR
{\ '7 Burner
Burner
base base
[_ CHECK IGNITERS
Operation of the electric igniters should be checked after the cooktop and supply line have been carefully
checked for leaks and the cooktop has been connected to the electrical power.
On models so equipped, check to be sure the cooktop is in the UNLOCKED position.
r_ Push and turn a burner valve to the LITE position. All spark igniters will make a series of sparks (ticking
sounds), but only the burner turned to LITE will light.
. The burner should light when gas is available to the burner.
. Once the burner lights, it should be turned out of the LITE position.
r_ Try each valve separately until all burners have been checked.

Installation Instructions
T
COOKTOP BURNERS ICONT.}
ITI BURNER IGNITION
Cooktop Spark Ignition-When you turn
the cooktop knob to LITE,the spark igniter makes a
series of electric sparks (ticking sounds) which light
the burner. During a power failure, the burners will
not light automatically. In an emergency, a cooktop
burner may be lit with a match by following the
steps below.
On models so equipped, check to be sure the
cooktop is in the UNLOCKED position.
r_ Light a match and hold the flame near the
burner you want to light. Wooden matches
work best.
r_ Push in and turn the control knob slowly. Be
sure you are turning the correct knob for the
burner you are lighting.
NOTE: If the burner does not light within five seconds,
turn the knob off and wait one minute before trying
again.
[_ THE BURNER FLAMES
Turn each burner on. Flames should be blue in color
with no trace of yellow. The burner flames should
not flutter or blow away from the burner. The flame
should be no less than 1/4" on the lowest setting
and no greater than 1-1/2" on highest setting.
_CAUTION: Ifyouattempt to measure the
flame, please use caution. Burns could result.
i/4" to
i-i/2" Cooktop Burner
Burners should be checked frequently
[_] BURNER GRATES
The three cooktop grates are designed for specific
positions. For maximum stability, these grates
should only be used in their proper position with
the edges positioned on top of the black bumpers
as shown
/
/
/
/
//
/'
//' //
/' /
//
/
Grote
Block Grote
Bumpers
10

Installation Instructions
OPERATION CHECKLIST
rA1 Make sure all controls are left in the OFF r_
position. Check to be sure the cooktop is in the
UNLOCKED position (on models so equipped).
Make sure the flow of air to and from the
cooktop is unobstructed.
The serial plate for your cooktop is located on
the bottom of the burner box. In addition to the
model and serial numbers, it tells you the ratings
of the burners and the type of fuel and pressure
the cooktop was adjusted for when it left the
factory.
B]
When ordering parts, always include the serial
number, model number and a code letter to
ensure proper replacement parts.
Recheck Steps:
Double check to make sure everything in this
guide has been completed. Rechecking steps
will ensure safe use of the cooktop.
11

Installation Instructions
MAKING THE LP CONVERSION
rT1 SAFETY INFORMATION YOU
SHOULD KNOW
The pressure regulator and burner orifices are set
for natural gas. To use LP gas, the regulator and
burner orifices must be converted. The LP orifice
spuds for the cooktop burners are attached to
the regulator along with separate LP conversion
instructions.
JI&L.,/'_LI/IUi_: The cooktop, as shipped from
the factory, is set for use with natural gas. If you
wish to use your cooktop with LP gas, you must
first replace the orifices and convert the pressure
regulator.
_I_W/_KI_I I i_1_: This conversion must be
performed by a qualified installer or gas supplier in
accordance with the manufacturer's instructions
and all codes and requirements of the authority
having jurisdiction. Failure to follow instructions
could result in serious injury or property damage.
The qualified agency performing this work assumes
responsibility for the conversion.
JlLL,,/'_L,!/IU|'_I: The following adjustments
must be made before turning on the burner. Failure
to do so could result in serious injury. Be sure
pressure regulator has been converted as
described in Step 2.
TOOLS YOU WILL NEED
FOR LP CONVERSION
7mm Nutdriver
Safety Glosses
Small Flat-Head
Screwdriver (4mm or
5/]2" tip size,60mm
or 2-]/8" long)
[2]
B]
Fa
ADJUST YOUR COOKTOP FOR USE
WITH LP GAS
Disconnect allelectrical power, at the main
circuit breaker or fuse box.
Shut off the gas supply to the cooktop
by closing the manual shut-off valve.
Adjust the pressure regulator, by the following
instructions:
*Unscrew the cap.
*Carefully look at the spring retainer to locate
the NAT or LP position.
N_
NAT.
Position
Cap Gasket_
LP L.P./Propone
Position
Pressure Regulator
. Turn the spring retainer over by rotating it
90 deg., pull it from the cap, turn the spring
retainer over so that LP is showing, insert it
back into the cap, and then rotate it 90 deg.
into position.
. Screw the cap back onto the regulator and
tighten.
12

Installation Instructions
MAKING THE LP CONVERSION (CONT.}
[_ CHANGE COOKTOP BURNER
ORIFICES
FA1 Remove the grates, burner caps, and burner
heads.
[] Using a 7mm nut driver, remove the burner
orifices. These may be accessed through the
burner holes in the cooktop.
Inner j_,(_
burner cap
Burner ,S_ Outer
base -"-__' _ burner
cap
Electrode Burner
Orifice spuds located _l/
through these openings
Tri-Ring Burner
OR
BurNer
base
Burner
cap
Burner
head
Orifice spud located Electrode
through this opening
Retainer
Ring
NOTE: On all burners, the
orifices have a spring-loaded
retaining ring around the hex
head to hold the orifice in the
nut driver during installation
and removal. A slight amount
of force is required to push the
nut driver down over the ring.
Fcl Locate the LPorifices attached to the regulator
along with separate LPconversion instructions.
They will have a digit for size and a letter for type
of gas, on the top or side. (Important: Save the
orifices removed from the appliance for future
use.)
Each orifice will show a series of engraved
marks, (I, II, III, IV or V), located on the top.
These marks denote the location of each orifice to the
cooktop burner.
For PGP976 Models
(Shorter)
For PGP986 & CGP650Models
r_ CHANGE COOKTOP BURNER
ORIFICES (CONT.)
PGP976
CGP650 & Main:58 L(x])
PGP986 Simmer: 5! L
CENTER BURNER
17,000 BTU/hr Extra Large Burner (PGP976 Models)
Extended spud for center
extra largeburner
Burner
Cap
Set Screw
I
ql_ Choke
I
I
Burner
Head
Extended
Spud
Base
Orifice spud located
through this opening
13

Installation Instructions
[T_ CHANGE COOKTOP BURNER
ORIFICES (CONT.)
CENTER BURNER
20,000 BTU/hr Tri-Ring Burner (PGP986 and CGP6SO
Models)
spuds located
through these
openings.
Main Orifice Main Orifice
Simmer Orifice
(Shorter) Main Orifice
_] CHANGE COOKTOP BURNER
ORIFICES (CONT.)
LEFT FRONT BURNER
(PGP986 and CGP650 Models)
Griddle Screw
The griddle screw
is marked with N
for natural gas
and L for liquefied
petroleum.
Main Orifice
NOTE: The main orifice is located in the center of
the burner, while the griddle screw is located to the
right of the center of the burner.
r6] Install the LPPropane orifices and griddle
screw (on PGP986and CGP6S0models only)
in their precise locations as noted in the
earlier illustrations.
r_ Return the natural gas orifices and griddle
screw to the bracket and attach the bracket
and the instruction sheet to the pressure
regulator using the screw removed previously.
r_ Replace the burner heads, caps and grates.
14

Installation Instructions
MAKING THE LP CONVERSION (CONT.}
ADJUST BURNER FLAMES
Turn all burners full on and check the flames.
They should be blue in color with some yellow
tipping at the ends of the flame. Foreign
particles in the gas line may cause an orange
flame at first, but this will soon disappear.
r_ Turn the cooktop burner knob to the lowest
setting while observing the flame.
Adjust the low flame setting using the valve bypass
screw as follows:
Low-setting adjustments must be made with two
other burners in operation on a medium setting.
This prevents the low flame from being set too low,
resulting in the flame being extinguished when
other burners are turned on.
E1 To adjust the flame,
remove the knobs. Use
screwdriver to remove
valve stem plugs as
shown.
Insert a screwdriver
through the access hole
in valve switch. Engage
adjustment screw in
valve. Refer to the
illustration below that
matches the adjustment
screw location for
your model. The
griddle burner (PGP986
and CGP650) has 2
adjustment screws,
one for the left rear
burner and one for the
left front burner during
griddle control. Griddle
control must be turned
to LO when making this
adjustment.
, If the flames were too
small or fluttered, open
Left of stem
For left front griddle
burner and tri-ring
burner simmer
adjustment screw
Inside ste m_'_._¢_
For all burners
except tri-ring
the valve more than the original setting.
, If the flames blew away from the burner,
close the valve more than the original
setting.
B] Hake the adjustment by slowly turning the
screw until flame appearance is correct.
r_ Testing Flame Stability:
Test 1 - Temporarily replace knobs. Turn the
knob from "HI" to the lowest setting
quickly. If the flame goes out at the
lowest setting, increase the flame size
and test again.
Test 2 - With the burner on the lowest setting,
open and close the cabinet door
under the cooktop. If the flame is
extinguished by the air currents
created by the door movement,
increase the flame height and test
again.
El Flame Recheck:
After the adjustment is made, turn all burners off.
Ignite each burner individually. Observe the flame
at the "HI" position. Rotate the valve to the lowest
setting and be sure that the flame size decreases
as the valve is rotated counterclockwise.
TO CONVERT THE COOKTOP BACK TO NATURAL
GAS, REVERSETHE STEPSUNDER HAKING THE LP
CONVERSION.
Once the conversion is complete and checked ok,
replace valve stem plugs and knobs, and fill out
the LP sticker. Include your name, organization and
date conversion was made. Apply the sticker near
the cooktop gas inlet opening to alert others in
the future that this appliance has been converted
to LP gas. If converting back to natural gas from
LP, please remove the sticker so others know the
appliance is set to use natural gas.
15

Notes.
16

Istructio s
d'i stallati Ta le de cuisson scell
au gaz de 91.4 cm (36")
PGP976, PGP986, CGP650
Web 8 I'adresse : www.electromenagersge.ca
AVANT DE COMMENCER
Avant de commencer, lisez attentivement la totalit#
de ces instructions.
.IMPORTANT - Conservezces
instructions pour votre inspecteur local.
, IMPORTANT - Respectez toutesles
ordonnances et les codes Iocaux.
, Note 6 I'installateur - Assurez-vous de laissez ces
instructions au consommateur.
, Note au consommateur - Conservez ces
instructions pour r6f6rence future.
, La garantie ne couvre aucune panne due
a une mauvaise installation.
AAVERTISSEMENT -
Cet appareil doit @trebien mis 6 la terre.
.IMPORTANT - vousdevez
v#rifierque cetappareiln'oitpas de fuite
conform#ment aux instructionsdu fabricant.
, L'installateur est responsable d'une bonne
installation et la garantie ne couvre aucune
panne due 6 une mauvaise installation.
A AVERTISSEMENT - D6brancheztout
courant #lectrique au niveau du disjoncteur de la
maison ou de la boTte 6 fusibles avant d'installer.
POUR VOTRE SI_CURITI_
A AVERTISSEMENT -
Si vous ne suivez pas exactement les instructions
de ce manuel, vous risquez d'occasionner un
incendie, une explosion ou une fuite de gaz, qui
peuvent provoquer des dommages mat#riels, des
blessures corporelles ou la mort.
Ne conservez pas ou n'utilisezjamais d'essence
ou d'autres liquides ou vapeurs inflammables 6
proximit# de cet appareil ou de tout autre appareil
m#naged
Ne pas installer ce produit si I'on utiJise une hotte
6 rideau d'air ou une hotte de cuisini_re soufflant
I'air au-dessus de la surface de cuisson. Le d_bit
d'air peut nuire au fonctionnement des br@leurs
6 gaz et repr_sente un risque d'incendie ou
d'explosion.
CI QUE VOUS DEVEZ FAIRE Sl
VOUS SENTEZ LE GAZ"
, N'essayezjamais d'allumer un appareil
#lectrom6nager. Netouchez 6 aucun
commutateur d'61ectricit6, n'utilisez jamais un
t616phonedans votre batiment.
, Appelez imm6diatement votre fournisseur de
gaz 6 I'aide du t616phoned'un voisin. Suivezles
instructions de votre fournisseur de gaz.
, Sivous ne pouvez pas entrer en contact avec
votre fournisseur de gaz, appelez les pompiers.
L'installation et le service de votre table de cuisson
doivent _tre faits par un installateur qualifi6, un
technicien de service ou votre fournisseur de gaz.
31-i0955 ii-13 GE i

Instructions d'installation
INSTRUCTIONS IMPORTANTES DE SI CURITI
Cette table de cuisson a 6t6 homologu6e UL. Vous
trouverez des pr6cautions 6 prendre en mati6re de
s6curit6 dans votre Guide d'utilisation et de soins.
Lisez-les attentivement.
. L'installation de votre table de cuisson
dolt se conformer aux codes Iocaux ou, en
I'absence de codes Iocaux, au National Fuel Gas
Code, ANSI Z223.1/NFPA 54 Derni6re 6dition.
. Assurez-vous que votre table de cuisson soit
bien install6e par un installateur qualifi6 ou un
technicien de service.
, Pour 61iminer tout mouvement corporel
au dessus des brOleurs de votre table de cuisson,
6vitez de placer des armoires de cuisine au
dessus des br01eurs.
. N'installezjamais votre appareil pr6s d'une porte
d'entr6e ou dans un emplacement oO un courant
d'air peut g6ner son usage.
s s
BESOINS D'ELECTRICITE
Cet appareil m6nager dolt 6tre Iivr6 avec le bon
voltage et la bonne fr6quence et branch6 6 son
propre circuit de d6rivation bien mis 6 la terre,
prot6g6 par un disjoncteur ou un fusible qui ont
I'amp6rage not6 sur la plaque min6ralogique de
votre appareil.
Nous vous recommandons de faire brancher le
cSblage 61ectrique et la fiche de votre cuisini6re
par un 61ectricien qualifi6. Apr6s I'installation,
demandez 6 1'61ectricien de vous montrer
I'emplacement de votre coupe-circuit principal.
Demandez 6 votre entreprise de services publics les
codes 61ectriques en vigueur dons votre r6gion. En
ne c_blant pas votre cuisini6re conform6ment aux
codes en vigueur, vous provoquez une situation
dangereuse. En I'absence de codes, vous devez
c_bler et isoler votre cuisini6re conform6ment aux
exigences du Canadian Electrical Code.
PII_CES COMPRISES
2vis R_gulateur 2 Supports de fixation
MATI'RIAUX DONT VOUS POUVEZ
AVOIR BESOIN
Agent de scellement
de tuyau Raccords de tuyau× Robinet d'alimentation de gaz
Raccord flexible de gaz approuv6 par I'ACNOR
DI min 3/8", Jonction NPT1/2
OUTILS DONT VOUS AUREZ BESOINS
Crayon
Tournevis Phillips
R_gle ordinaire ou de
v@ification
Lunettes de s_curit_
Scie sauteuse
CI66 tuyau
Perceuse 6 main ou _lectrique
et foret de !/8po

Instructions d'installation
LISTE DE VITRIFICATION AVANT INSTALLATION
[]
@
Pour pr6parer I'ouverture de la surface de
cuisson, vous devez vous assurer que
I'int6rieur de I'armoire ne touche pas la table
de cuisson {consultez la section sur la
pr6paration de I'ouverture).
Enlevez les mat6riau× d'emballage, les
boTtes de grille, le r6gulateur avec sa
documentation et la documentation de
votre table de cuisson avant de commencer
6 I'installer.
Documentotion
cuisson
Bottes de
grille
/
DEnlevez les instructions d'installation de la
trousse de documentation et lisez-les
soigneusement avant de commencer.
Assurez-vous de bien ranger toute la
documentation,(Hanuel du propri6taire,
Instructions d'installation, etc.) dans un
endroit sOr pour r6f6rence future.
r67Assurez-vous d'avoir tousles outils et tous
les mat6rau× n6cessaires avant de
commencer 6 installer votre table de
cuisson.
rE7 Votre maison dolt @tre aliment6e en courant
61ectrique ad6quat pour vous permettre de
bien utiliser en toute s6curit6 votre table de
cuisson. (Consultez la section sur les besoins
d'61ectricit6.)
r_ pour installer votre table de cuisson dans
votre maison, assurez-vous de vous
conformer scrupuleusement 6 tous les
codes et 6 toutes les ordonnances locales.
[] Assurez-vous que les rev6tements de mur, le
comptoir et les armoires autour de la table
de cuisson puissent supporter la chaleur
[pouvant atteindre 93°C {200°F)] produite
par la table de cuisson.

Instructions d'installation
PREPARATION DE L'OUVERTURE
r_ vous DEVEZ RESPECTERLES
DEGAGEMENTS MINIMAU× SUIVANT
Profondeur max de 55 R- MIN.
cm (15") des armoires
en surplomb D6gagement
entre I'ouverture
et ]e mur Iot@al
I droit
D#gagement min. de 76 cm
(30") du comptoir 6 la surface Hauteur min
en non surplomb non prot6g#es 45 cm (18")
C - MIN. du comptoir
D6gagement 6 I'armoire la
entre I'ouverture plus proche
et ]emur arri_re de chaque
:6t6 de
I'appareil
L - MIN. D#gagement
entre la d6coupe et le
mur lot@a] gauche
2-1/2" MIN. Entre I'ouverture
et le devant du eomptoir
L
PGP976 9,5 cm(3-5/4")
PGP986
CGP650
Base d'armoire
de 76,2 cm (30")
ou sup@ieur
R C
15,2 cm (6") 8,6cm(3-3/8")
30,5 cm (12") 30,5 cm (12") 8,6cm(3-3/8")
30,5 cm (12") 30,5 cm (12") 8,6cm(3-3/8")
TOUS LES D#GAGEMENTS HORIZONTAUX DOIVENT
S'APPLIQUER SUR UNE DISTANCE MINiMALE DE 45,7 CM
(18") AU-DESSUS DE LA SURFACE DE CUISSON.
REMARQUE :Laissez un 9,4cm ]
d6gagement vertical minimum (3-11/1B")(
de 1,1cm (7/16 po) entre le
dessus de la table de cuisson
(ou une profondeur minimum
de 9,4 cm (3 11/16 po) et route
surface combustible, par
exemple un tiroir d'armoire.
Pour une installation en Tlot,maintenir
1,1 cm (7/16")
une distance minimum de 6,3 cm (2 !4 po)
entre le bord et le dos du comptoir. Garder un espace de
7,6 cm (3 po) minimum sur Ins c6t@sdu comptoir,
[_] DIMENSIONS DU DI_COUPAGE DE
LA TABLE DE CUISSON
76 cm (30") _-'" 53 cm (21")
_4 -1/4 cm
(3-1/4"1
o--_ --.._ _i- 72 cm (28-1/4")
49 cm 119-3/8"1 _
r_ DIMENSIONS TOTALES DE LA TABLE
DE CUISSON
Pour assurer lajustesse du d_coupage, ilvaut mieux faire
un gabarit pour couper I'ouverture dans le comptoir.
Largeur du d#coupage
72,4 cm 128-i/2"1 cm 119-S/8"1
longueur du d#coupag_.__<_ 36,2 cm
(14-i/4")
[_ EMPLACEMENT RECOMMANDE DE
L'ALIMENTATION DE G.AZ
PARTIR DU MUR ARRIERE
Emplacement
recommand6 de
I'aJimentation
de gaz
2.5 cm (i")min. du mur artiste
[_] ASSUREZ-VOUS QUE LES
REVETEMENTS MUR, LE COMPTOIR
ET LESARMOIRES AUTOUR DE LA
TABLE DE CUISSON PUISSENT
SUPPORTER LA CHALEUR
(POUVANT ATTEINDRE 93°C [200°F])
pouvoir supporter
une chaleru pouvant
atteindre 95°C (200°F)
[]_ INSTALLATI.ON POUR PERSONNE.
HANDICAPEE SEULEMENT (E.-U. •
DISABILITIES ACT FORWARD
APPROACH) •
Laissez une profondeur
minimum de 12,7 cm
(5 po) entre la table de
cuisson et une enceinte.
REMARQUE : L'enceinte
dolt #tre construite en bois.
Aussi, un panneau d'acc#s
est n#cessaire pour la prise
#lectrique, le r#gulateur de
<12,7,5")
2
r
pression, le robinet de sectionnement, les supports
de retenue et I'entretien ou les r#parations.