GE KTD-404 Operating instructions

9
D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
Programming
Initial Programming
KTD-404 Programming
Use the following steps to program the KTD-404:
Step 1) Supply power to the unit. The LCD will momentarily isplay the wor s Controller
Keypa  or the type of keypa . Next, the normal operating isplay menu will appear:
Enter the access co e
5
,
7
,
9
,
seq
. The isplay will automatically a vance
to the next menu.
This section provi es instructions for programming the KTD-404 keypa an for using it to
program other components in the DIGIPLEX system, inclu ing:
 Pan/Tilt/Zoom Receiver Programming
 Vi eo Switcher Programming
 Alarm Interface Programming
 CyberDome Programming
P/T/Z receiver programming an initial entry into programming for other system components
is provi e ; please refer to component manuals for complete programming instructions.
Helpful Hint: For large DIGIPLEX III systems, the KTD-311 Software Downloa Package
can be use to easily ownloa camera titles.
For new installations, these instructions shoul be followe in the or er in which they are
presente . If any programme ata nee s to be change at a later ate, the menu associate
with that ata can be accesse by entering the appropriate programming mo e an using
the esignate key(s) to a vance to the menu.
The KTD-404 offers many programming choices which i entify how it will function in the
system. A separate co e is use to access the menus that escribe these choices.
Programming choices for the KTD-404:
System Size  Camera Access  Multiplexer Type  Annunciation
 Monitor Offset  Monitor Access  Multiplexer Views  Entry Verification
Step ) Enter the programming mo e by pressing an hol ing the
set
key until the
following isplay appears:
Normal Operating Display
Figure 9: Co e Entry Display
ENTER PROGRAMMING
CODE:
Figure 8: Normal Operating Display
CAMERA 000
MONITOR 01
Code Entry Display

10 D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
Camera Site Access
System Size
Step 3) The CLEAR MEMORY option will erase all ata in the controller keypa s
nonvolatile memory an reloa factory efault values.
To clear the keypa s memory, press
1
. The isplay will automatically a vance
to the menu shown in Figure 11.
If the CLEAR MEMORY function is not to be use , press
0
an go to Step 5.
Step 4) This menu offers a safety check. If a
3
is entere , the controller keypa s
memory will be reloa e with factory efault values. If a
0
is entere , there will
be no change. The isplay will automatically a vance to the next menu.
Step 5) This menu is use to set the system size. Use the numerical keys to enter the
largest camera number, largest monitor number, largest multiplexer number, an
largest preset number in the system. Maximum entries are: cameras-511,
monitors-64, multiplexers-64, an presets-63.
Press
seq
to a vance to the next column, or move the joystick left or right to switch
between columns. Once all entries are ma e, the isplay will automatically
a vance to the next menu.
Step 6) This menu is use to eny or permit the controller keypa s access to certain
camera sites. Press
0
to eny access or
1
to permit access. After each
selection, the next camera number will appear. Move the joystick up or own to
switch between cameras. When one, press
seq
to a vance to the next menu.
Figure 13: Camera Site Access Display
CAMERA 000 ACC=YES
0=NO 1=YES SEQ=NEXT
Figure 12: System Size Display
SYST SIZE (CAMERAS)
511 64 64 63 SEQ=NEXT
Figure 11: Secon Clear Memory Display
ARE YOU SURE?
0=NO 3=YES SEQ=NEXT
Clear Keypad Memory Figure 10: Clear Memory Display
CLEAR MEMORY?
0=NO 1=YES SEQ=NEXT
Helpful Hint: Pressing the
seq
key will forwar you through programming without changing
the set parameters.

11
D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
Multiplexer Enabled
Step 8) This menu etermines which multiplexers can be enable (accesse ) from the
keypa . This must be one for each keypa in the system. To enable a
multiplexer, press
1
. When enable , the Multiplexer Select Menu isplay
(Figure 16) will appear. Pressing
0
will a vance to the next multiplexer in the
system. Moving the joystick up or own will switch between multiplexer bran s.
Press
seq
to a vance to the monitor offset menu isplay (Figure 18).
Multiplexer Select
Step 9) When a multiplexer has been enable , this menu allows selection of ifferent
mo els of multiplexers. Use the joystick to scroll through the list. The mo els are
liste in alphabetical or er. After selecting the appropriate multiplexer, press
seq
to a vance to the next menu.
Multiplexer View
NOTE:
Figure 17: Multiplexer View Display
IEW: PIP YES
0=N 1=Y =NEXT SEQ=NEXT
Figure 16: Multiplexer Select Display
MPLXR 01: BURLE
SELECT ( ) SEQ=NEXT
Figure 15: Multiplexer Enable Display
MPLXR 01 ACC=YES
0=NO 1=YES SEQ=NEXT
Monitor Access
Step 7) This menu is use to eny or permit the controller keypa s access to certain
monitors. Press
0
to eny access or
1
to permit access. After each selection,
the next monitor number will appear. Move the joystick up or own to switch
between monitors. When one, press
seq
to a vance to the next menu.
Figure 14: Monitor Access Display
MONITOR 01 ACC=YES
0=NO 1=YES SEQ=NEXT
If no multiplexers are enable , the message No multiplexers have been programme  will
be isplaye any time the key is presse .
alt
Step 10) This menu etermines which views will be enable when the keypa is in
multiplexer operating mo e. (When in multiplexer operating mo e, pressing the
key toggles through the views selecte here.) Move the joystick own to
scroll through the list of views available. For each view, press
1
to accept or
0
ecline. When all views have been selecte , press
seq
to return to the Multiplexer
Enable menu isplay. Note: Some multiplexers o not allow specific view
selection an will skip this menu.
view

12 D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
After the entry, the isplay will automatically a vance to the next menu:
NOTE:
In some applications, a user may prefer to have the monitors numbere simply as
1, 2, 3, etc., instea of using the matrix switcher output number. To allow for
the ifference in numbers, simply subtract the esire monitor number from the
matrix switcher output number, an enter the result as the monitor offset.
Example: Suppose a keypa has a monitor that is connecte to matrix switcher
output #12. To enable the monitor to be a resse as Monitor #1, subtract 1 from
12 an enter the result (11) as the monitor offset.
(Matrix Switcher Number) - (Monitor Number) = (Offset)
(12) - (1) = (11)
In this particular example, if more than one monitor were to be controlle from the
keypa , a itional monitors woul be connecte to matrix switcher outputs 13, 14,
15, etc. an woul be controlle as Monitor 2, Monitor 3, Monitor 4, etc.
The keypa will eny any monitor offset number that conflicts with Largest Monitor an
Monitor Access programming choices that were ma e earlier in this section (Refer to Step
4 an Step 6).
Step 1 ) When place in the annunciation mo e, the KTD-404 will annunciate call-in
requests generate by access control receivers or a KTD-463 Alarm Chassis. In
this mo e, the keypa will stack 32 calls in the or er in which they are receive .
Annunciation will change the LCD menu on the Normal Operating Display. The
numbers of the first three sites to call in will appear in the LCD win ow, as shown
below:
Annunciation
CAM 000 1ST 2ND 3RD
MON 01
Figure 20: Normal Operating Display with Annunciation
ANNUNCIATION? NO
0=NO 1=YES SEQ=NEXT
Figure 19: Annunciation Display
Monitor O set
Step 11) The efault program for the keypa ictates that the selecte monitor number will
correspon to the number of the matrix switcher output to which it is connecte .
For example, if Monitor 12 appears in the keypa s isplay win ow an a camera
selection is ma e, the monitor that is connecte to output 12 of the matrix switcher
will switch to that camera.
Figure 18: Monitor Offset Display
MONITOR OFFSET
NUMBER? 00 SEQ=NEXT

13
D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
Tone Type
Step 13) If the KTD-404 has been programme for annunciation, it will pro uce an au ible
tone when a call-in request is receive . This tone can be programme to be a
single frequency or multiple frequency (warble).
Select the esire call tone. The isplay will automatically a vance to the next
menu.
Entry Veri ication
Step 14) This option changes how camera an monitor numbers are selecte while the
keypa is in the normal operating mo e.
For example, without entry verification, keying in
0 0
9
woul automatically
call up camera site number 9. With entry verification, keying in
9
, will
perform the same task.
Enabling entry verification changes the function of the
talk
key on the KTD-404
esktop keypa , an the
face
key on the KTD-304R rack-mount keypa . Both
become the key. An keycap has been supplie with the unit. Refer to
Keycap Replacement, Appen ix B.
Keep in min that selecting the entry verification function will cause the talk
function to be isable . If both the talk function an the entry verification function
are to be enable at the same time, contact Kalatel for instructions.
Once an entry is ma e, the LCD menu will return to the Normal Operating Display
(Figure 8).
For annunciation, press
1
. The LCD menu will isplay Figure 21.
For no annunciation, press
0
, an go to Step 14.
ENTRY ERIFICATION? NO
0=NO 1=YES SEQ=EXIT
Figure 22: Entry Verification Display
CALL TONE TYPE? MULT
0=SINGLE 1=MULT SEQ=NEXT
Figure 21: Tone Selection Display

14 D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide

15
D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
System Component Programming
To program system components through a KTD-404 keypa , begin at the normal operating
isplay an procee as follows:
Figure 23: Normal Operating Display
CAMERA 000
MONITOR 01
Step 1) Press an hol the
set
key until the following isplay appears:
Figure 24: Co e Entry Display
ENTER PROGRAMMING
CODE:_
Step ) Enter the access co e
9
,
5
,
1
,
seq
. The isplay will automatically a vance
to the next menu.
From this menu it is possible to perform vi eo switcher programming, P/T/Z receiver
programming, alarm interface programming, an CyberDome programming by pressing the
correspon ing number on the keypa .
P/T/Z receiver programming instructions can be foun on the following pages. For etaile
programming instructions on the CyberDomes, alarm interfaces, an vi eo switchers,
please refer to the pro uct programming instructions.
If you are programming a CyberDome Day-Nite or CyberDome Select with a KTD-404
keypa , the
1st
key can be use to step backwar s while in the programming menus.
NOTE:
Figure 25: First Menu Display
1=SWTCHR 2=RC R 3=ALARMS
4=CYBERDOME SEQ=EXIT

16 D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
Pan/Tilt/Zoom Receiver
Programming
Receiver Site Select
The following steps outline the receiver setup proce ure. Beginning at the normal operating
isplay, procee as follows:
Each receiver offers mo e of operation choices, many of which can be programme using
a KTD-404 series keypa . The keypa can also store preset position information, if
applicable.
Accessing the Receiver Setup Menus (Steps 1-3)
Step 1) Press an hol the
set
key until the following isplay appears:
Enter the access co e
9
,
5
,
1
,
seq
. The isplay will automatically a vance
to the next menu.
Step ) Press
2
. The first receiver programming menu will appear:
Step 3) Using the numerical keys, enter the receiver site to be programme . The isplay
will automatically a vance to the next menu.
Receiver Setup (Steps 4-16)
Figure 30: Receiver Setup Menu Display
1=SETUP 2=PRESETS
SEQ=EXIT
Figure 29: Receiver Site Selection Display
ENTER RECEI ER SITE
NUMBER 000 SEQ=EXIT
Figure 28: First Menu Display
1=SWTCHR 2=RC R 3=ALARMS
4=CYBERDOME SEQ=EXIT
Figure 27: Co e Entry Display
ENTER PROGRAMMING
CODE:
Figure 26: Normal Operating Display
CAMERA 000
MONITOR 01

17
D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
Invert Pan/Tilt
Pan Cycle
Autopan Autostart
Choice Description
This choice disables the receiver’s auto pan function altogether.
This choice assigns a 50% duty cycle when the receiver is in
This choice assigns a 100% duty cycle when the receiver is in
auto pan mode (i.e., unit alternately pans and rests for 8
second intervals).
auto pan mode (i.e., unit continuously pans).
in auto pan mode.
This choice will cause the receiver to pan randomly when
0
1
2
3
Lens Voltage
Step 6) If the pan/tilt receiver is to auto pan, enter one of the four following choices liste
in the chart below:
The isplay will automatically a vance to the next menu.
Step 7) In the event that receiver power is lost, the receiver can be programme to resume
auto pan once power is restore . If the receiver is to auto pan when power is
restore , press
1
. If not, press
0
. The isplay will automatically a vance to
the next menu.
Step 8) Select the appropriate voltage for the receiver sites motorize lens. Press
0
for
6 volts or
1
for 12 volts. The isplay will automatically a vance to the next menu.
Figure 33: Lens Voltage Display
LENS OLTAGE?
1=12 0=6 SEQ=NEXT
Figure 32: Autostart Display
AUTO PAN AUTOSTART?
1=YES 0=NO SEQ=NEXT
Figure 31: Pan Cycle Display
PAN CYCL? 0=0% 1=50%
2=100% 3=RDM SEQ=NEXT
Step 4) Press
1
to begin receiver setup. The isplay will automatically a vance to the
first setup menu.
Figure 34: Invert Pan/Tilt Display
IN ERT PAN/TILT?
0=NO 1=YES SEQ=NEXT

18 D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
Zoom Direction
Focus Direction
Iris Direction
Step 9) This selection allows the pan an tilt irections to be reverse in an application
where a camera must be mounte in an inverte position. Press
1
to invert, or
0
for normal pan/tilt operation. The next isplay will appear.
Step 10) The next three menus provi e choices for efining the polarity of the output voltage
for the motorize lens connecte to the receiver.
Press
0
if the lens requires positive voltage for zoom in an negative voltage
for zoom out. Press
1
if the opposite is the case. The next isplay will appear.
Step 11) Press
0
if the lens requires positive voltage for iris open an negative voltage
for iris close. Press
1
if the opposite is the case. The next isplay will appear.
Step 1 ) Press
0
if the lens requires positive voltage for focus near, an negative
voltage for focus far. Press
1
if the opposite is the case. The next isplay will
appear.
Step 14) With the CLR RCV MEM option, the KTD-404 will instruct the P/T/Z receiver to
erase all ata in its nonvolatile memory an reloa factory efault values.
To clear the receivers memory, press
1
. The isplay will automatically a vance
to the menu shown in Figure 39.
Clear Receiver Memory
Figure 35: Zoom Direction Display
ZOOM DIRECTION
0=POS 1=NEG SEQ=NEXT
Figure 36: Iris Direction Display
IRIS DIRECTION
0=POS 1=NEG SEQ=NEXT
Figure 37: Focus Direction Display
FOCUS DIRECTION
0=POS 1=NEG SEQ=NEXT
Figure 38: First Clear Memory Display
CLR RC R MEM? CAM 000
0=NO 1=YES SEQ=NEXT
If the clear receiver memory function is not to be use , press
0
to return to the
Receiver Site Selection menu isplay (Figure 29).