GE Fluorostar User manual

GE Healthcare
Fluorostar™®
00-441130-01 IPC1000 BIOS Setup with integrated PC-guard support
for IPC 1000 Radisys Endura JD35Q
IPC 1000 (0,5k x 0,5k ) 00-453962-01 and higher
IPC 1000 (1k x 1k) 00-453963-01 and higher
Version 09.12.03

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 2 of 13
Manual Text Revision History
Rev Dash Date Change Description
[A] [01] [09-01-2009] [Initial]
[B] [01] [03-12-2009] Add Clear RTC RAM description
This document contains advanced service information that is company confidential. Due to the proprietary nature of the contents the document should be
viewed by GE personnel only. This manual may not be reproduced, in whole or in part, without the written permission of GE OEC Medical Systems, Inc.
OEC is a registered trademark of GE OEC Medical Systems, Inc. Other product and company names mentioned herein are the property of their respective
owners.
The contents of this document are accurate at the time of publication. However, changes in design and additional features can, at any time, be incorporated
in the hardware and software and may not be reflected in this version of the document. Contact GE OEC Technical Support for clarification, if discrepancies
arise.
GE OEC Medical Systems, Inc., a General Electric Company, going to market as GE Healthcare.
Note:
Changes from default Bios settings marked with this text stile
© 2009
GE OEC Medical Systems GmbH
90530 Wendelstein
Germany
All rights reserved

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 3 of 13
WARNING • THIS SERVICE MANUAL IS AVAILABLE IN ENGLISH ONLY.
• IF A CUSTOMER’S SERVICE PROVIDER REQUIRES A LANGUAGE OTHER THAN ENGLISH, IT IS THE CUSTOMER’S RESPONSIBILITY TO
PROVIDE TRANSLATION SERVICES.
• DO NOT ATTEMPT TO SERVICE THE EQUIPMENT UNLESS THIS SERVICE MANUAL HAS BEEN CONSULTED AND IS UNDERSTOOD.
• FAILURE TO HEED THIS WARNING MAY RESULT IN INJURY TO THE SERVICE PROVIDER, OPERATOR OR PATIENT FROM ELECTRICAL
SHOCK, MECHANICAL OR OTHER HAZARDS.
AVERTISSEMENT • CE MANUAEL DE MAINTENANCE N’EST DISPNIBLE QU’EN ALNGAIS
• SI LE TECHNICIEN DU CLIENT A BESOIN DE CE MANUEL DAN UNA AUTRE LANGUE QUE L’ANGLAIS, C’EST AU CLIENT QU’IL
INCOMBE DE LE FAIRE TRADUIRE.
• NE PAS TENTER D’INTERVENTION SUR LES ÉQUIPMENT TANT QUE LE MANUEL SERVICE N’A PAS ÉTÉ CONSULTÉ ET COMPRIS.
• LE NON-RESPECT DE CET AVERTISSEMENT PEUT ENTRAÍNER CHEZ LE TECHNICIEN, L’OPÉRATEUR, OU LE PATIENT DES BLESSURES
DUES À DES DANGERS ÉLECTRIQUES, MÉCANIQUES OU AUTRES.
WARNUNG • DIESES KUNDENDIENST-HANDBUCH EXISTIERT NUR IN ENGLISCHER SPRACHE.
• FALLS EIN FREMDER KUNDENDIENST EINE ANDER SPRACHE BENÖTIGT IST ES AUFGABE DES KUNDEN FÜR EINE ENTSPRECHENDE
ÜBERSETZUNG ZU SORGEN.
• VERSUCHEN SIE NICHT, DAS GERÄT ZU REPARIEREN, BEVOR DIESES KUNDENDIENST-HANDBUCH NICHT ZU RATE GEZOGEN UND
VERSTANDEN WURDE.
• WIRD DIESE WARNUNG NICHT BEACHTET, SO KANN ES ZU VERLETZUNGEN DES KUNDENDIENSTTECHNIKERS, DES BEDIENERS
ODER DES PATIENTEN DURCH ELEKTRISCHE SCHLÄGE, MECHANISCHE ODER SONSTIGE GEFAHREN KOMMEN.
AVISO • ESTE MANUAL DE SERVICIO SÓLO EXISTE EN INGLÉS.
• SI ALGÚN PROVEEDOR DE SERVICIOS AJENO A GEMS SOLICITA UN IDIOMA QUE NO SEA EL INGLÉS, ES RESPONSABILIDAD DEL
CLIENTE OFRECER UN SERVICIO DE TRADUCCIÓN.
• NO SE DEBARÁ DAR SERVICIO TÉCNICO AL EQUIPO, SIN HABER CONSULTADO Y COMPRENDIDO ESTE MANUAL DE SERVICIO.
• LA NO OBSERVANCIA DEL RESENTE AVISO PUEDA DAR LUGAR A QUE EL PROVEEDOR DE SERVICIOS, EL OPERADOR O EL PACIENTE
SUFRAN LESIONES PROVOCADAS POR CAUSAS ELÉCTRICAS, MECÁNICAS O DE OTRA NATURALEZA.
ATENÇÃO • ESTE MANUAL DE ASSISTÉNCIA TÉCNICA SÓ SE ENCONTRA DISPONÍVEL EM INGLÉS.
• SE QUALQUER OUTRO SERVIÇO DE ASSISTÉNCIA TÉCNICA, QUE NÁO A GEMS, SOLICITAR ESTES MANUALS NOUTRO IDIOMA, É DA
RESPONSABILIDADE DO CLIENTE FORNECER OS SERVIÇO DE TRADUÇÁO.
• NÁO TENTE REPARAR O EQUIPAMENTO SEM TER SONSULTADO E COMPREENDIDO ESTE MANUAL DE ASSISTÉNCIA TÉNICA.
• NÁO CUMPRIMENTO AVISO PODE POR EM PERIGO A SEGURANÇA DO TÉCNICO, OPERADOR OU PACIENTE DEVIDO A’ CHOQUES
ELÉCTRICOS, MECÁNICOS OU OUTROS.

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 4 of 13
AVVERTENZA • IL PRESENTE MANUALE DI MANUTENSIONE É DISPONIBILE SOLTANTO IN INGLESE.
• SE UN ADDETTO ALL MANUTENSIONE ESTERNO ALL GEMS RICHIEDE IL MANUALE IN UNA LINGUA DIVERSA, IL CLIENTE É TENUTO
A PROVVEDERE DEIRETTAMENTE ALLA TRADUZIONE.
• SI PROCEDA ALL MANUTENZIONE DELL’APPARECCHIATURA SOLO DOPO AVER CONSULTATO IL PRESENTE MANUALE ED AVERNE
COMPRESO IL CONTENUTO.
• NON TENERE CONTO DELLA PRESENTE AVVERTENZA POTREBBE FAR COMPIERE OPERAZIONI DA CCUI DERIVINO LESIONI
ALL’ADDETTO ALLA MANUTENZIONE, ALL’UTILIZZATORE ED AL PAZIENTE PER FOLGORAZIONE ELETTRICA, PER URTI MECCANICI OD
ALTRO RISCHI.

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 5 of 13
Preparation
Open the front cover od the system. Set on IPC1000 PC-Guard to OFF
Figure 1 PC Guard ON/OFF
Connect a keyboard to the system
To enter BIOS Setup press “DEL” while IPC1000 is booting. You can see then BIOS screens on main monitor A.
Tipp: On Compact and on Compact Dual (without installed B392) it can happen that you don’t see the Boot Screen. Replace gender
changer to 00-906513-02 or use an external monitor connected directly on Graphic card A with a standard DVI/VGA cable.

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 6 of 13
Notice: After replacing BIOS battery clear RTC RAM before setting the BIOS setup
Clear RTC RAM (CLRTC)
The CLRTC jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date , time and system setup
parameters by erasing the CMOS RTC RAM data. The RAM data in CMOS, that include system setup information such as system passwords , is
powered by the onboard button cell battery.
To erase the RTC RAM:
1. Turn off the system and unplug power cord
2. Remove onboard battery
3. Move the jumper JRTC1 from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds,
then move the cap back to pins 1-2
4. Replace the battery
5. Plug the power cord and turn ON the system
To enter BIOS Setup connect a PC-keyboard and press “DEL” while IPC1000 is booting.
You can see then BIOS screens on main monitor A.

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 7 of 13
Figure 2 Jumper JRTC1

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 8 of 13
1. MAIN
1.1 System Time [08:29:03] (Set to actual time)
1.2 System Date [01.09.2009] (Set to actual date)
1.3 Hard Disk Pre-Delay [Disabled]
1.4 Serial ATA [Enabled]
1.5 Native Mode Operation [Auto]
SATE RAID Enable [Disabled]
SATA AHCI Enable [Enabled]
SATA AHCI Legacy Enable [Disabled]
1.6 SATA Port 0 [320GB SATA1]
1.7 SATA Port 1 [NONE]
1.8 SATA Port 2 [NONE]
1.9 SATA Port 3 [NONE]
1.10 SATA Port 4 [NONE]
1.11 SATA Port 5 [NONE]
1.12 Ext. Primary Master [NONE]
1.13 Ext. Primary Slave [NONE]

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 9 of 13
2. ADVANCED
2.1 Boot Features
Quiet Boot [Enabledl]
Quick Boot Mode [Enabledl]
ACPI Mode [Yes]
ACPI Sleep Mode [S1]
High Precision Event Timer [Yes]
Power Button Behavior [4-sec Override]
Resume on Modem Ring [Off]
Resume on PME# [On]
PS2 KB/MS Wake Up [Disabled]
USB Wake Up [Disabled]
Power Loss Control [Power On]
Legacy USB Support [Enabled]
Summery Screen [Enabled]
2.2 Advanced Processor Options
CPU Speed: Automatically Set
Core Multi Processing [Enabled]
Machine Checking [Enabled]
Thermal Management 2 [Enabled]
Adjacent Cache Line Prefetch [Enabled]
Set Max Ext CPUID = 3 [Disabled]
C1 Enhanced Mode [Disabled]
Intel ® Virtualization Technology [Disabledl]
No Execute Mode Mem Protection [Enabled]
Enhanced Intel Speed Step [Disabled]

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 10 of 13
2.3 Advanced Chipset Control
Integrated Device Control Sub Menu
USB Host Controller [Enabled]
Memory Reclaiming [Enabled]
Enable VT-d [Disabled]
Default Primary Video Adapter [PEG]
IGD-Device 2 [Disabled]
Azalia Audio [Auto]
Route Port 80h cycles to [PCI]
2.4 Memory Cache
Cache System BIOS area [Write Protect]
Cache Video BIOS area [Write Protect]
Cache Base 0-512k [Write Back]
Cache Base 512k – 640k [Write Back]
Cache Extened Memory area [Write Back]
2.5 PnP Configuration
PCI32 Slot 1
Option ROM Scan [Enabled]
Enable Master [Disabled]
Latency Timer [Default]
PCI32 Slot 2
Option ROM Scan [Enabled]
Enable Master [Disabled]
Latency Timer [Default]
PCI32 Slot 3
Option ROM Scan [Enabled]
Enable Master [Disabled]
Latency Timer [Default]
PCI32 Slot 6
Option ROM Scan [Enabled]
Enable Master [Disabled]
Latency Timer [Default]

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 11 of 13
PCIE x1 Slot 4
Option ROM Scan [Disabled]
Enable Master [Disabled]
Latency Timer [Default]
PCIE x4 Slot 5
PCI Express Port #5 [Auto]
Option ROM Scan [Enabled]
Enable Master [Disabled]
Latency Timer [Default]
PCIE x16 Slot 7
PCI Express Graphics Port [Auto]
PEG Port Enabled Yes
PEG Port Number 02h
PEG Width x16
PEG Port Slot Number 1000h
PEG Power Limit 75 watts
PEG Slot Card Detect yes
Onboard Lan 2
Option ROM Scan [Disabled]
Enable Master [Disabled]
Latency Timer [Default]
Onboard Lan 1
Option ROM Scan [Disabled]
Enable Master [Disabled]
Latency Timer [Default]
2.6 I/O Device Configuration
KBC Clock Input [12 MHz]
COM1 [Enabled]
Base I/O address [3F8]
Interrupt [IRQ 4]
COM2 [Enabled]

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 12 of 13
Mode [Normal]
Base I/O address [2F8]
Interrupt [IRQ 3]
Parallel Port [Enabled]
Base I/O address [378]
Interrupt [IRQ 7]
Mode [ECP]
DMA Channel [DMA 3]
2.7 Hardware Monitor
CPU Temperature Threshold [75°C]
Fan Speed Control Modes [Disable (Full speed)]
3. Security
Supervisor Password Is Clear
User Password Is Clear
Fixed disk boot sector [normal]
Password on boot [Disabled]
4. BOOT
Boot Priority order 1. PCI SCSI : P0-WDC …
All other entry: empty
5. EXIT
Use Exit & save Changes

00-441130-01_IPC1000 BIOS Setup_Radisys_Endura_JD35Q.doc Company Confidential
Page 13 of 13
6. Reboot system
Set PC-Guard to ON and reboot system.
6. Used keys
ÅÆ Select Screen
ÇÈ Select Item
Enter Go to Sub Screen
F 1 General Help
F 9 Setup defaults
F 10 Save and Exit
ESC EXIT