Gear Light S400 PRO User manual

GearLight S400 PRO Rechargeable Headlight
GearLight S400 PRO Rechargeable Taillight
USB Charging Cables
User Manual
Warranty Card
1x
1x
1x
1x
2x
PACKAGE CONTENTS
CHARGE
BEFORE
FIRST USE
S400 PRO
RECHARGEABLE
User Manual
FOR YOUR SAFETY, READ BEFORE OPERATING
The lights are not a replacement or substitute for your bicycle’s original reflectors.
Please check your local regulations before operating the lights.
WARNING
If the bike light does not turn on, or works intermittently:
• Charge the bike light for 3 hours or until the red LED indicator light turns green.
If the bike light does not charge:
• Inspect the bike light and charging cable for any damage or corrosion.
• Check the USB charging cable connections and the power source.
• Replace the USB charging cable.
Note: A computer in sleep mode might not charge the bike light.
If the bike light appears dim or faded:
• Charge the bike light for 3 hours or until the red LED indicator light turns green.
• Replace the USB charging cable.
If the problem persists, contact GearLight for a replacement.
052021
When the lights are not in use, store them with a moderate level of charge and in
a cool place away from flammable materials. Once every few months, discharge
the batteries fully and recharge.
Irvine, California | USA | www.GearLight.com
GearLight warrants this product for one year from the date of purchase against any
defects in material or workmanship. This warranty does not cover normal wear and
tear, nor damage resulting from misuse or neglect. We will, at our discretion, repair,
replace, or refund the purchase price of this product should we determine it to be
defective.
Liability limited to the purchase price of this product. GearLight shall not be liable
for any incidental or consequential damages or any implied warranty on this
product. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
WARRANTY AND LIMITATION OF LIABILITY
Limited One-Year Warranty
Limitation Of Liability
TROUBLESHOOTING
MAINTENANCE
For product support, contact Customer Service:
[email protected]om

• Wrap the silicone strap (Fig. 6) around the
bike frame and attach it to the strap hook.
•To rotate the taillight, press on the release
latch (Fig. 7) and slide the taillight o.
•Rotate to desired position (Fig. 8), press on
the release latch, and slide the taillight back
on.
•There are four dierent lighting modes:
High, Slow Chase, Strobe, Fast Chase
•To switch through the dierent lighting
modes, press down on the power button to
alternate through the four modes.
•To switch through the dierent lighting
modes, press down on the power button to
alternate through the five modes.
•To turn the taillight on, press down on the
power button located on the front of the
taillight.
•To turn the taillight o, press down on the
power button to cycle through all the
lighting modes until the light is o.
• Wrap the silicone strap (Fig. 3) around the
handlebar (Fig. 4) and attach it to the
strap hook (Fig. 5).
•There are five dierent lighting modes:
High, Medium, Low, Strobe w/ Side Strobe
Lights, Medium w/ Side Strobe Lights
•To turn the headlight on, press down on
the power button located on the top of
the headlight.
•To turn the headlight o, press down on
the power button to cycle through all
the lighting modes until the light is o.
BEFORE AND DURING EACH USE, ENSURE THE RUBBER COVER IS SECURED OVER THE USB
CHARGING PORT. DO NOT USE THE LIGHTS IN HEAVY RAIN.
OPERATIONS
HEADLIGHT TAILLIGHT
On/O
Switching Modes
How to Mount the Headlight How to Mount the Taillight
Switching Modes
On/O
HIGH MEDIUM LOW STROBE W/
SIDE STROBE
LIGHTS
MEDIUM W/
SIDE STROBE
LIGHTS
HIGH SLOW CHASE STROBE FAST CHASE
POWER
BUTTON
POWER
BUTTON
FIG. 6 FIG. 7 FIG. 8
FIG. 3 FIG. 4
FIG. 5
Lift the rubber cover to locate the USB charging port.
Note: To charge the taillight, press down on the release latch to
slide the taillight out. It is unnecessary to unmount the
taillight to charge.
Connect the light to the USB charging cable
(Fig. 1 & Fig. 2).
Connect the charging cable to a powered USB port,
such as a phone charger, power bank, or computer.
Unplug the USB charging cable when the LED indicator turns green or after 3 hours of
charging. Note: The battery may be fully charged even if the indicator does not turn green.
Blinking Red Power Button =
CHARGING
Solid Green Power Button =
FULLY CHARGED
Solid Red LED Indicator =
CHARGING
Solid Green LED Indicator =
FULLY CHARGED
STRAP
HOOK
POWER
BUTTON
SILICONE
STRAP
RELEASE
LATCH
SILICONE
STRAP
STRAP
HOOK
USB CHARGING
PORT
USB CHARGING
PORT
POWER BUTTON
HEADLIGHT CHARGING TAILLIGHT CHARGING
•The bike lights contains lithium batteries that can present a fire, explosion, and burn hazard.
•Do not repair, disassemble, or modify the bike lights.
•Do not charge or store the bike lights near flammable materials.
•Do not charge with a wet or damaged USB charging cable.
•Do not overcharge the bike lights; unplug the bike lights once fully charged or if left unattended.
•Use only UL-Listed charging adapters rated at 5V 2.4A max.
•Do not use or charge the bike lights if they are wet or damaged.
•Do not use the bike lights while they are charging. Unplug the bike lights before use.
•Keep the lights away from fire, water, and high temperatures.
•Failure to follow safety instructions may result in fire, personal injury, and damage to property.
WARNING
GETTING STARTED
Charging the Bike Light Set
Fully charged in approximately 3 hours. Fully charged in approximately 2 hours.
Blinking LED Indicator =
LOW BATTERY WARNING: During use, the bike lights
will BLINK RED to indicate LOW BATTERY.
THE BIKE LIGHTS WILL TURN OFF WITHIN MINUTES.
Charge before use.
!
LOW BATTERY WARNING
FIG. 1
FIG. 2
SIDE
STROBE
LIGHTS
1
2
3
4