Gear Light TAC1 User manual

TAC1 LED TACTICAL FLASHLIGHT
Operation Guide
TROUBLESHOOTING
If the flashlight does not turn on, or works intermittently:
Replace the batteries.
Make sure the tail cap is twisted on tightly and batteries are inserted correctly.
If the flashlight flickers or changes modes automatically:
Make sure the tail cap is twisted on tightly.
If the light appears dim or faded:
Irvine, California | USA | www.GearLight.com
WARRANTY AND LIMITATION OF LIABILITY
MAINTENANCE
Inspect the flashlight monthly and carefully remove any damaged batteries and clean
any corrosion. If the flashlight is used less than once a month, remove the batteries
between uses. Lubricate all threads and rubber O-rings with petroleum jelly twice
yearly.
Limited One-Year Warranty
GearLight warrants this product for one year from the date of purchase
against any defects in material or workmanship. This warranty does not cover
normal wear and tear, nor damage resulting from misuse or neglect. We will,
at our discretion, repair, replace, or refund the purchase price of this product
should we determine it to be defective.
Limitation Of Liability
Liability limited to the purchase price of this product. GearLight shall not be
liable for any incidental or consequential damages or any implied warranty on
this product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
If the problem persists, possible LED Failure. Contact GearLight for a replacement.
Replace the batteries.
2x GearLight TAC1 LED Tactical Flashlights
2x Battery Tubes (Batteries Are Not Included)
2x AAA Battery Holders (Inside Flashlights)
1x Operation Guide
1x Warranty Card
Package Contents:
IMPORTANT SAFETY NOTICE: Lithium-ion batteries are potentially hazardous and can present a
fire, explosion, and burn hazard. By using lithium-ion batteries, you agree that GearLight shall not
be liable for any incidental or consequential damages arising from, relating to or connected with the
use of lithium-ion batteries. If you do not agree with these conditions, please use only alkaline or
NiMH rechargeable batteries.
FOR YOUR SAFETY, READ BEFORE OPERATING
v1

WARNING: To avoid eye injury, do not stare directly into the light beam or shine the
beam directly into anyone’s eyes. This product is not designed, intended, or
recommended for children or hazardous environments.
CAUTION: The flashlight may become warm or hot after extended periods of use.
This is typical for high-powered flashlights and does not cause damage to the
flashlight.
WARNING: Lithium-ion batteries can present a fire, explosion, and burn hazard. Use
only 18650 battery cells with a protection circuit produced by Panasonic, Sanyo, Sony,
Samsung, or LG. Remove the battery when the flashlight is not in use. The use of other
cell manufacturers or the failure to follow the battery manufacturer's safety instructions
may result in fire, explosion, personal injury, and damage to property.
WARNING: Always follow the battery manufacturer’s instructions as to the proper
usage, handling, storage, and disposal of batteries. Use only batteries from a reputable
manufacturer. Do not mix dierent brands or types of batteries in the same flashlight.
Replace all batteries at the same time. Failure to follow safety instructions may result in
personal injury and damage to property.
AAA Battery Installation
1. Unfasten tail cap and remove battery holder.
2. Insert 3 AAA batteries following the correct
polarity (+,-) marked on the battery holder.
3. Insert the battery holder back into the
flashlight with the positive (+) end first.
On/O
Zoom
1. Hold both ends of the flashlight; gently twist and pull each end away from the
other.
2. Pull the two ends away from each other to zoom in and push the two ends
together to zoom out.
To turn the flashlight on, press down firmly on the red power button located
on the tail of the flashlight until you hear a click.
To turn the flashlight o, press down firmly again until you hear a click.
There is a single lighting mode. (High)
18650 Lithium-ion Rechargeable Battery Installation (See Warning)
1. Insert one 18650 battery inside the 18650 clear battery tube.
2. Insert the combined 18650 battery and clear tube into the flashlight with the
positive (+) end first.
GETTING STARTED
OPERATION
ZOOMABLE RUBBER
O-RING
AAA
BATTERY
HOLDER
TAIL CAP
WARNING: Remove the batteries if the flashlight is not working properly.
Failure to do so may result in personal injury and damage to property.
POSITIVE NEGATIVE
BELT CLIP
ANTI-ROLL
DESIGN
HIGH
MODE