Geemarc AmpliDECT250 User manual

AmpliDECT250
TM
User Guide p2
Notice d’utilisation p40
Benutzerhandbuch p89

2
Description
Handset/ Base 4
LCD screen 6
Characters List 7
Menu 8
Installation
Connection 9
Batteries setting up 9
Batteries use 9
Using the telephone
On/Off setting 11
Key lock 11
Receiving a call 11
Making a call 12
Hands free mode 13
Last number redial 14
Recalling Recent Numbers 14
Mute function 14
Receiving volume 15
Paging the handset 15
Direct call 15
Index
Handset settings
Ringer setting 16
Key tone setting 16
Silence mode 17
Language setting 17
Time/Date setting 18
User name 18
Personnal Identification Number 19
Emergency number (store & call) 20
Restore factory settings 21
Base settings
Base setting access 22
Tone Dialling Switch over 22
Flash setting 23
Insert pause 23
Personal Identification Number 24
Base Melody 25
Base Volume 25

3
Phone book
Create an entry 26
View entries 26
Delete an entry 27
Clear all entries 27
Modify an entry 28
Caller Display (CID)
Dial from CID list 29
Voice mail and CID list 30
Waiting call indicator 30
Delete entries in CID list 31
Clear all entries 31
Transfer from CID list to phone book 32
Additional handsets /base
Add a new handset 33
Release a registered handset 33
Make an internal call 34
Call transfer between Handsets 34
Conference call 35
Add an extra base 35
Troubleshooting 36
Index
General information
Warranty 38
Recycling instruction 39

4
Description

5
Description

6
Description
In standby mode, handset number, user name (if stored), time and date are all displayed on the LCD
Description

7
When you want to create an entry e.g. name, phone number, you will need to use the keypad. Every
key on the keypad represents a set of letters, numbers and symbols. See the table above.
Use ‘C’ to correct a mistake i.e. clear the last digit entered
Use * key to move from uppercase to lowercase
Characters List

8
Note: If you are unsure what to do whilst in the menu system, stop pressing keys and simply wait 30
seconds, the telephone will automatically return to standby mode.
Menu

9
1 - Connection
Connect the line cord plug to the line socket on the base. Connect the other end of the line cord to
the PTT socket. (**)
Plug the power cable into the power socket on the base. Plug the adaptor into
the mains supply. (*)
2 – Battery installation
Install the rechargeable batteries in the handset. The handset requires three Nickel Metal Hydride
(NiMH) AAA batteries. These are supplied with your telephone.
Check the battery polarity diagrams on the handset when inserting the batteries.
Fit the battery cover by sliding the cover on to the back of the handset until it
snaps shut
3- Battery status
Place the handset on the base, a short beep will be heard. The Power/Charging indicator lights up
(red). The battery symbol will be displayed on the handset. Once the handset is fully charged, the
display will show a full battery symbol.
Installation

10
The telephone has an automatic charging control to avoid excessive charging.
Before the handset can be used, the handset batteries must be charged for a
minimum of 15 hours on the base.
Note:
When batteries get low during a call, there will be a warning tone (beep), you
will have to place the handset on the base to recharge
(*) Classified "hazardous voltage" according to EN60950 standard
(**) Classified TNV-3 according to EN60950 standard.
Installation

11
1- Handset On/Off
When the handset is placed on the charger it automatically switches ON.
Otherwise press key until it switches ON
To turn the handset off, press key until 'Good Bye' appears. The LCD
display will then switch off .
2- Key lock
When this feature is turned on, all buttons except for , will be locked and will not function.
Incoming or intercom calls can be answered by using key. However, when
you complete the call and hang up, the telephone returns to lock mode.
This feature is useful to avoid pressing buttons by mistake.
Switch lock On: Press until "locked" appears in the LCD display.
Switch lock Off: Press until "locked" disappears from the LCD.
Using the Phone

12
3- Receiving a call
When an incoming call is received the telephone rings and the L1 icon will flash on the LCD display.
If the caller can be identified (due to subscription to a Caller Display service), the caller's telephone
number will be displayed.
If the handset is in the base, lift it up and press key otherwise just press key. During the
conversation the LCD screen displays the connection time.
You can adjust the earpiece volume, use ▲and▼to adjust the volume 1 to 4.
Note: If you have an incoming call with the keypad locked, it is automatically unlocked
4 - Making a call
Pick up the handset, press key. When you hear dialing tone, dial the
number on the keypad.
Using the Phone

13
To end the call simply press again or place the handset on the base
Pre-dialing: Pick up handset. Dial the number on the keypad, press the
number is automatically dialled.
To end the call simply press again or place the handset on the base.
Note:
If you make an incorrect entry while pre-dialling the telephone number:
- Press C to clear the last digit and then enter the correct number
- Press C for longer than one second to clear all digits entered and return to
standby mode.
If you wish to insert a pause when storing a number, press until P appears in the LCD display.
5 - Hands free mode
This function is used when you don't want to have the handset near your ear or when you want other
people to hear at the same time.
When you are in conversation Press and hold until displays, use ▲and▼to adjust the
volume 1 to 4.
To release hands free mode, do the same as above.
Using the Phone

14
6 - Last number redial
To redial the last number dialed:
Pick up handset. Press in standby mode then press to dial the number (or first, followed
by )
7 - Recalling recent numbers
You can call back any of the last 10 numbers dialled as follows: Pick up handset, press , the last
dialled number is displayed; use repeatedly to see the other nine dialled numbers. Press to
dial the number.
Note: You may clear some digits or all with C key then edit your new number.
To return to standby mode, Press C for longer than 1 second
8 - Mute function
If you wish, you can speak privately to someone else in the room without your
caller overhearing.
You will still be able to hear the caller but they cannot hear you during the mute operation.
During a call, press C, the LCD display will show
Press C again to resume the conversation
Using the Phone

15
9 - Receiving volume and tone
During a conversation you may adjust the volume by using the button or the tone with
button OR use ▲and▼to select the volume (1 to 4)
10 - Paging the handset
If you wish to locate the handset: press the button on the base
All registered handsets will be paged and will ring for about 30 seconds. Press any button on the
located handset to stop paging mode or press again
11 - Direct call
You may record one number in the memory " Direct call". On pressing any key, this number will be
dialled automatically
This function is useful for a young child unable to use the telephone correctly or for a disabled person
living alone
To activate this function:
Use ▲and▼to select "HS setting" Press OK
Use ▲and▼to select "Direct call"
Press OK
Enter your desired number
Press OK to confirm or use C key to modify
The screen will display "DIRECT CALL"
To disable the function press the "R" key twice (quickly)
Using the Phone

16
1 - Melodies setting for external/internal calls
There are 2 types of melodies
- 9 for externals calls
- 9 for internals calls
You may select one melody for external calls and a different one for internal calls.
Use ▲and▼to select "HS setting"
Press OK
Use ▲and▼to select "Melody Ext" or "Melody Int"
Press OK
Use ▲and▼to select your melody and then press OK
Use ▲and▼to select the level (1 to 4)
Press OK
Press C to return to the melody menu or press to return to standby
mode.
2 - Key tone setting
On: the keys beep when pressed
Off: silence
To activate or de-activate:
Use ▲and▼to select "HS setting"
Handset Settings

17
Press OK
Use ▲and▼to select " Key Tone"
Press OK
Use ▲and▼to select "On" or "Off"
Press OK
Press C twice or once to return to standby mode …
3 - Silence mode
In this mode only the shaker will work, all other sounds the telephone can emit will be disabled e.g.
ringer, key beeps.
To activate this function:
Press key until "Silence" is displayed
To cancel the function press the same key until you see the standby screen again
4 - Language setting
You can choose one of many languages language, to do this :
Use ▲and▼to select "HS setting"
Press OK
Use ▲and▼to select "language"
Handset Settings

18
Press OK
Use ▲and▼to select your language
Press OK to validate
Press C twice or once to return to standby mode …
5- Time/Date setting
The time displayed on the handset can be changed. The time format is 24 hours.
Use ▲and▼to select "HS setting"
Press OK
Use ▲and▼to select "Set clock"
Press OK
"Input time" is displayed
Enter the time using the numerical keypad (0-9)
Press OK to validate
You can modify the date at the same time (Day - Month - Year).
6 - User name
The given name will be displayed on the screen in "standby mode".
Use ▲and▼to select "HS setting"
Press OK
Use ▲and▼to select "User name"
Handset Settings

19
Press OK
Use the keypad to enter the name, see details page 7.
Press OK to validate
Press C twice or once to return to standby mode …
7 - Personal Identification Number (PIN)
The PIN is required for the following options:
- Registering a new handset
- Resetting a handset
- Changing settings found under the base menu
The PIN is pre-set to '1590' (factory default). This can be changed - this is
recommended for confidentiality.
Use ▲and▼to select "HS setting"
Press OK
Use ▲and▼to select "Set PIN"
Press OK
"HS PIN" is displayed
Enter the old code or factory code
Press OK
"New PIN" is displayed
Enter your new code using the 0 to 9 keys
Press OK to validate
Handset Settings

20
"Retype PIN" is displayed
Enter your new code again
Press OK
Press C twice or once to return to standby mode …
8 - Emergency number
You can store a special number in case of emergency e.g.doctor, family member
Use ▲and▼to select "HS setting"
Press OK
Use ▲and▼to select "Emergency"
Press OK
Enter your chosen number
Press OK
"Stored" is displayed
Press C twice or once to return to standby mode …
To call this number simply press button, it will be automatically dialled
Handse
t Settings