Geemarc AmpliPOWER 40 User manual

AmpliPOWER 40/50
English
Français
Deutsch
!!!Warning, AmpliPOWER40/50 has an extra loud receiving
volume gain!!! (Risk of acoustic shock)
!!!Attention, l’AmpliPOWER40/50 possède un amplifiacteur
de volume très puissant!!! (Risque de choc accoustique)
!!!Seien Sie vorsichtig: der AmpliPOWER40/50 hat ein sehr
starke Lautstärke!!! (Akustisches Schockrisiko)

!!!User manual to read carefully before start to
use!!!
!!!Manuel d’utilisation à lire impérativement avant
la mise en service!!!
!!! Bevor Ihr neues Telefongerät zu benutzen,
bitte lesen Sie dies Benutzerhandbuch sehr
sorgfältig!!!
CAUTION: this telephone is specifically designed for the people with hearing
difficulties and is provided with a handset earpiece volume control for individual
requirements. Due care must be taken by all users that the handset earpiece
volume control is set to the lowest level acceptable by each respective user.
Care should therefore be exercised to ensure that any naive users are familiar
with this requirement.
ATTENTION: Ce téléphone peut être destiné aux personnes ayant des
problèmes auditifs. il possède un écouteur a volume variable. A la première
utilisation, assurez vous que le volume soit réglé au minimum. Les personnes
malentendantes pourront par la suite augmenter le volume pour l’adapter à leur
besoin.
WARNUNG: Dieses Telefon wurde speziell für schwerhörige Personen
konzipiert und besitzt eine auf die individuellen Bedürfnisse einstellbare
Hörerlautstärke. In Folge dessen sollten alle Nutzer darauf achten, dass der
Lautstärkeregler des Hörers, in Rücksicht auf andere Nutzer, auf das
niedrigste Niveau gestellt wird. Es ist darauf zu achten, dass unwissende
Benutzer mit der Handhabung dieser Apparatur vertraut gemacht werden.

Index
INDEX
Description 5-7
Setting up
1 - Connecting the telephone 8
2 - Alarm and ring options 8
-Ring only
-Ring and shaker
-Ring and strobe flash
3 - Ringer settings 9
4 - Tone/Pulse switch (T/P) 10
5 - Time break recall switch (270/100) 10
6 - Hotel message waiting switch 10
7 - Wall mounting 11
Using the phone
8- Answering incoming calls 12
-Without headset
-With headset (option)
-In handsfree mode
9- Volume and tone receiving 13

4
10 - Making a cal 15
- Without headset
- With headset (option)
- In handsfree mode
11 - Last number redial 16
12 - Recall, * & # buttons 16
13 - Mute button 17
14 - Storing telephone numbers 17
15 - Dialling stored numbers 18
Options:
16 - Direct Vibe handset 19
17 - Shaker 20
18 - Headset with microphone 20
Guarantee 21
For product support and help visit our
website at www.geemarc.com
telephone [phone]
or fax [phone]
Index

5
IndexDescription
Reception tone
adjustment
Last number redial
Memory storing
Mute
Flashing incoming ring indicator
Direct memories
3 emergency
numbers Reception volume
adjustment
Time break recall
Extra volume and
tone adjustment
Handset cord socket
Clip for wall
mounting
Red light of tone/
volume activation
Speaker volume
adjustement
Handsfree /
Headset button

Description
Battery
compartment
Time break
recall
Dialling mode
Pulse/Tone
Handset
cord socket
Memo card
Holes for wall
mounting
6

Description
7
Ring Hi/Low/
OFF Switch
Ring alarm
setting
Volume and tone
adjustment ON/OFF switch
Line socket
Hotel switch
message
Shaker socket
Headset socket Adaptator
socket

8
1- Connecting the telephone
- Connect the handset cord.
- Open the battery door by unscrewing the
retaining screw. Insert 4 x AAA alkaline batteries
(not included).
Snap the battery door in place.
In case of power failure, batteries are required
for the ring.
- Connect the line cord.
- Connect the shaker cord (optional).
- Connect the headset cord (optional).
- Connect the PTT plug to the wall socket.
- Connect the 12V DC adaptor cord to the
telephone.
- Connect the 12V DC adaptor to your
wall socket (**).
(**) Classified “hazardous voltage” according to EN60950 standard.
2- Alarm and ringer volume setting
A 3 position switch located on the right side
of the phone allows the settings below:
Setting up

9
(*) Classified TNV-3 according to EN60950 standard.
-
: Ringer and shaker are activated.
-
: Ringer and strobe flash are activated.
3- Ringer settings
A switch located on right side allows the ringer to
be switched HI,LOW,OFF:
: Off, : Low,
: Hi
Your phone comes with the ringer switched to
«High» and the melody set to «6».
Low Mid High
Melody 1 1 2 3
Melody 2 4 5 6(by default)
Melody 3 7 8 9
If you don’t like the ringer melody,you can choose
a new one by changing the settings as follow:
- Lift the handset.
- Press button.
- Press # button.
- Press any button 1 to 9.
Ringer will be activated on next call.
Setting up

10
- 0 : Only the ringer is activated.
4- Tone/Pulse switch (T/P)
The Tone/Pulse switch is factory pre-set to
Tone position (T). In the UK,all telephone
exchanges now use Tone dialling.If your phone
does not dial out, it is probably being used from
an older private switch- board (PBX). In this
case,theTone/Pulse switch must be moved to
Pulse.
5- Time break recall switch (270/100)
For the UK, the TBR switch is factory pre-set to
100ms. It can be switched to 270ms for other
locations or PBX’s.
6- Hotel message waiting switch
These are used with the new services provided on
hotel network. A switch located behind your
phone allows to set ON the hotel message waiting
function.When the switch is setting ON and when
you receivea message, the red light is
Setting up