Geemarc DALLAS 100 VM User manual

DALLAS 100 VM
English
AMPLIFIED TELEPHONE WITH
OUTGOING VOICE MODULATION

2
DESCRIPTION
(*) Classified TNV-3 according to EN60950 standard.
Last number
redial
Ringer Volume
settings
Indirect
memory
button
Quick Dial
locations,
M1,M2 and M3
Line cord
socket*
R button (for private exchanges)Amplify
Sending level
amplified
setting
GENERAL DESCRIPTION
Memory storing key
Handset tone
slide control Handset volume slide control
Ringer tone
setting
Handset
Clip for
wall
mounting
Voice
meter

3
Thread the line cord
through this groove
REAR
BASE
Amplify
default
setting
Dialing
mode
setting
Flash
setting Telephone
line socket
Voice level
meter setting
DESCRIPTION

4
1 - CONNECTING TELEPHONE
1 - Connect the handset cord.
2 - Connect the line cord to the socket located
at rear of telephone then connect the PTT
plug*.
2 - RINGER VOLUME SETTING
Aswitchlocatedontherightsideallowstheringer
to be switched to HI, LOW or OFF
SETTING UP
(*) Classified TNV-3 according to EN60950 standard.

5
SETTING UP
3 - RINGER TONE SETTING
A switch located on the right side allows the
melody to be switched to HI, Middle or LOW.
4 - WALL MOUNTING
To wall-mount your telephone, slide out the clip
turn around and slide back into the wall mounting
position (located in the base unit, just below the
ear piece).This will ensure that the handset stays
firmly in position. Make 2 holes in the wall 85mm
apart, insert the wall plugs and the wall mounting
screws. The screws should protrude from wall
by 6-7 mm. Place the phone onto the screw-
heads and slide down to secure.

6
SETTING UP
5 - TONE/PULSE SWITCH (T/P)**
The Tone/Pulse switch is factory pre-set to Tone
position (T).In the UK,all telephone exchanges
now use Tone dialing. If your phone does not dial
out it is probably being used from an older pri-
vate switch board (PBX). In this case, the Tone/
Pulse switch must be moved to Pulse (P).
** Please note that this switch is not to be moved
after setting.

7
USING THE PHONE
1 - ANSWERING INCOMING CALL
- When an incoming call is received the phone
will ring and flash. To answer the call lift the
handset and speak.
- On completion of the call, carefully replace the
handset in the cradle to release the line.
2 - VOLUME RECEIVING ADJUSTMENT
You can increase the volume according to your
own hearing requirements.
Use the button, located on the front side, to
adjust the level according to your own hearing
requirements.

8
3 - TONE RECEIVING ADJUSTMENT
Ifthereceivervolumehasbeenamplified,thetone
control can also be adjusted. You can adjust and
increase the low frequency or high frequency
sounds with the tone slide control on the front
edge of the unit.
Note: The tone adjustment function will not be
effective when the receiver volume is set to nor-
mal level.
4 - MAKING ACALL
- Lift the handset.
- Await the dial tone and dial required number.
- On completion of the call, carefully replace the
handset in the cradle.
USING THE PHONE

9
5 - SENDING LEVEL ADJUSTMENT
Ifyourvoiceisquietorcalledpartieshavedifficulty
hearing you, you can increase the sending level
volumewiththeswitch locatedontheright
side.
6 - LAST NUMBER REDIAL
- Lift the handset.
- Await the dial tone and press button.
- The previously dialled number will be
automaticaly redialled (not in use for memory
numbers).
7 - R , * & # BUTTONS
These are used with the new services provided
on digital exchanges. For details please contact
your network operator.
USING THE PHONE
0db +4db

10
8 - STORING TELEPHONE NUMBERS
Your phone can store 3 direct and 10 indirect
memories(16digitsmaximumforeach memory).
- Lift the handset.
- Press button.
- Dial the telephone number you wish to store.
- Press button.
- Press one of the direct memory buttons, M1,
M2, M3.
Or press M and any button 0 to 9 on the key pad
under which you wish to store the telephone
number in indirect memory.
- Replace the handset.
Note:Numbers will belost if youdisconnectyour
phone. Entering a new number in memory will
automatically erase the previous number.
USING THE PHONE