Geemarc ClearSound CL64 User manual

CL64
Amplified Classic Phone
Téléphone Vintage Amplifié
Lautverstärktes Retrotelefon
English1~12
Français13~24
Deutsch25~36

1
User manual to be read carefully before use!
CAUTION: this telephone is specifically designed for people with
hearing difficulties and is provided with a handset earpiece volume
control for individual requirements. Due care must be taken by all
users that the handset earpiece volume control is set to the lowest
level acceptable by each respective user. Care should therefore be
exercised to ensure that any naive users are familiar with this
requirement.

2
CONTENTS 2
DESCRIPTION 3
General Description 3
SETTING UP 5
1 - Connecting the telephone 5
2 - Ringer volume setting 5
3 - Auto Dial Switch 6
4 –Auto On Hook 6
VOLUME AND TONE ADJUSTMENT 7
1 - Receiving volume and tone adjustment 7
2 - Sending volume adjustment 8
USING THE PHONE 9
1 - Answer a call 9
2 - Making a call 9
3 - Storing telephone numbers 9
4 - Dialing stored numbers 10
GUARANTEE 11
GENERAL INFORMATION 12
CONTENTS

3
General Description
Battery low LED
Ringer LED &
Amplify On LED
&
AMPLIFY On/Off button
Auto Dial SOS number
ON/OFF Switch
Ringer UK/EURO Select
Switch
Amplify ON/OFF
slide switch
Lock the
Battery Door
4XAA Size
Battery
Compartment
Store Button
DESCRIPTION
Auto turn off Switch
Ringer Loud/High/Low/
OFF Switch

4
Slide Volume Control
Send Amplify
-3 / 0 / +3
Slide TONE
Control
DESCRIPTION

5
1 - Connecting the telephone
- Connect the handset cord.
- Open the battery door by turning around the locking tab.
Insert 4 alkaline batteries (type AA 1.5V, not supplied) in the
compartment (*). Batteries are required if you wish to
increase the ringer level up to 10 dB & also use the
“Mechanical Bell” ringer feature.
Replace the battery door and turn the locking tab to the
locked position.
- Connect the line cord plug into the line socket on the rear of
the unit (*).
- Connect the other end of the line cord into the wall PTT
socket (*).
2 - Ringer volume setting
The phone is equipped with “Mechanical Bell” ringers which can be
selected between UK (tring..tring) & European (triiiiiiiiiiiing) style
bells, via the switch located in the battery compartment.
The mechanical bell sound is functional only when the batteries are
inserted and are not run down.
When there are no batteries or the batteries are “low” the Battery
low indicator flashes and the ringer sound is the normal two tone
electronic ring.
A switch located on the right side allows the ringer to be switched to
LOUD Hi, Low or Off:
: Off
: Low
: Hi
: LOUD
SETTING UP
(*) Classified TNV-3 according to EN60950 standard.

6
Note: The ring level will be increased of 10 dB if you insert
batteries.
3 –Auto Dial Switch
When this switch is in ON position ( ), the phone will automatically
dial out the number stored in the SOS memory if no other dial button
is pressed for 4 seconds. Set this switch as per your requirement.
4 –Auto On Hook
When this switch is in the On position ( ), the phone will
automatically go On Hook (disconnect the telephone line) when the
person at the other end disconnects the line, even if the handset is
not replaced on the cradle.
In case the handset is removed from the cradle and there is a phone
call, the phone will still ring as usual. To answer the call, pick up the
handset, press and release the hook button once.
SETTING UP

7
1 - Receiving volume and tone adjustment
You can increase the volume and adjust the receiving tone
according to your own hearing requirements.
When the switch located under the phone is ON ( ), the extra-
receiving and tone functions are automatically activated each time
you use the phone.
When this switch is OFF ( ), you will need to activate the function
by pressing the button .
Pressing the button (AMPLIFY ON/OFF switch) allows extra
receiving and tone functions to be activated during the conversation.
When the function is activated, the red light of extra receiving and
tone function located below the ringer LED lens lights up
Adjust the TONE and VOLUME buttons to fit the levels to your own
hearing requirements.
VOLUME AND TONE ADJUSTMENT

8
Note: When the tone (treble), earpiece volume and sending levels
are set to the maximum, whistling may occur. Then the sending
level settings should be decreased with the switch .
When the switch located in the bottom of the phone base is ON
( ), the extra-receiving and tone functions are automatically
activated each time you use the phone. When this switch is OFF
( ), you will need to activate the function by pressing the button
.
Tone and volume (15dB to 30dB) adjustment is only activated when
the button is set to ON ( ). When this button is set to OFF
() only the volume can be adjusted from 0dB to 15dB.
2 - Sending volume adjustment
If your voice is quiet or called parties have difficulty hearing you, you
can increase the sending level volume with the switch located on
the right side. You can also decrease the sending volume if
required.
VOLUME AND TONE ADJUSTMENT

9
If you are using this telephone with a hearing aid, set your
hearing aid to the T setting.
1 -Answer a call
- When an incoming call is received the phone will ring and the
ringer LED will flash, to answer the call lift the handset and
speak.
- On completion of the call, carefully replace the handset in the
cradle to release the line. See also section on Auto/Manual
switch
2 - Making a call
- Lift the handset.
- Await the dial tone and press the SOS, M1 or M2 buttons
once
- On completion of the call, carefully replace the handset in the
cradle.
See also section on Auto Dial On/Off switch
3 - Storing telephone numbers
Your telephone has a SOS memory button with 112 stored as
default and also two other memory buttons, M1 & M2
This SOS number can be changed to a number of your choice
which can be up to 18 digits. To change the SOS memory:
USING THE PHONE