GEIGER GFB00 Series User manual

1
www.geiger.de EN
EN
DE Original-Montage- und
Betriebsanleitung
Original assembly and
operating instructions
Notice originale de montage
et d’utilisation
Instrucciones originales de
instalación y funcionamiento
Istruzioni originali di installazione
e funzionamento
EN
FR
ES
IT
Hand-held transmitter
GFB00.

2Gerhard Geiger GmbH & Co. KG | 100W1650 1121V000en
EN
EN
Index
1. General information..................................................................2
2. Guarantee ..................................................................................2
3. Hand-heldtransmitterspecicsafetyinstructions ...............2
4. Scopeofdelivery ......................................................................2
5. Overview GFB00. ......................................................................3
6. Insert batteries ..........................................................................3
7. Initial commissioning ...............................................................3
8. Deleting a hand-held transmitter.............................................4
9. Replacing a lost hand-held transmitter ..................................4
10. Resettingthedrivetothedeliverystate.................................4
11. Copyinghand-heldtransmitterswithoutadrive ...................4
12. Resettingthehand-heldtransmittertothedeliverystate ....5
14. Technical data ...........................................................................5
15. Declarationofconformity ........................................................5
16. Disposal information ................................................................5
1. General information
Dear customer,
By purchasing a GEIGER radio-controlled hand-held transmitter you have decided on a quality
product from GEIGER.
Thank you very much for your decision and the condence placed in us.
2. Guarantee
In the case of incorrect installation contrary to the operating instructions and/or constructional
modication, the legal and contractual guarantee for property damage and product liability
lapses.
3. Hand-heldtransmitterspecicsafetyinstructions
Please observe following instructions in order to avoid damage to this product:
fAvoid impacts.
fDo not drop the device.
fDonotimmerseinwateroranyliquid.Ensureprotectionagainstsplashingwater.
fNever use cleaning agents or abrasive solvents. Clean the surface of the transmitter
with a damp cloth.
fDonotallowchildrentoplaywithxedcontrols.
fRemotecontrolsaretobekeptawayfromchildren.
4. Scopeofdelivery
• Hand-held transmitter
• Batteries 2 x LR03, type AAA
• Operating instructions

3
www.geiger.de EN
EN
5. Overview GFB00.
6. Insert batteries
7. Initial commissioning
Teaching-inthersttransmitter
1. Connect the drive to the power supply. The drive clicks (short UP and DOWN movement)
and starts in teach-in mode.
For multi-channel hand-held transmitters: Select the desired channel.
2. Press the UP and DOWN keys on the hand-held transmitter simultaneously until the drive
clicks. The hand-held transmitter and the drive are connected to each other.
Changing the rotation direction of the drive
1. Press the PAIR key for at least 5 seconds. The drive clicks.
2. Press the STOP key for at least 2 seconds. The drive clicks, the direction of rotation of the
drive has been changed.
Teaching-in another hand-held transmitter
1. Press the PAIR key for at least 5 seconds on the hand-held transmitter that has already been
programmed. The drive clicks.
2. Press the PAIR key on the new hand-held transmitter for at least 2 seconds.
The drive clicks, the new hand-held transmitter has been programmed.
PAIR key
Battery
compartment
Status LED
UP
key
ST
OP key
DOWN
key
Front view Rear view without
bottom part
230 V

4Gerhard Geiger GmbH & Co. KG | 100W1650 1121V000en
EN
EN
8. Deleting a hand-held transmitter
1. Press the PAIR key on a hand-held transmitter that is not to be deleted for at least 5 sec.
The drive clicks.
2. Press the PAIR key for at least 10 seconds on the hand-held transmitter that is to be deleted.
The drive clicks, the hand-held transmitter has been deleted.
9. Replacing a lost hand-held transmitter
1. Disconnect the drive from the power supply for at least 2 seconds.
2. Reconnect the drive to the power supply for 10 seconds.
3. Disconnect the drive from the power supply for at least 2 seconds.
4. Connect the drive to the power supply again. The drive clicks.
5. Press the PAIR key on a new hand-held transmitter for at least 2 sec.
The drive clicks, the new hand-held transmitter is taught-in.
I ATTENTION:Thelosthandtransmitterisstillstoredinthedrive.
Ifyouarenotsurewherethishandtransmitteris,allhand-heldtrans-
mitterscanbedeletedbyresettingthedrivetothedeliverystate.
10. Resettingthedrivetothedeliverystate
1. Disconnect the drive from the power supply for at least 2 seconds.
2. Reconnect the drive to the power supply for 10 seconds.
3. Disconnect the drive from the power supply for at least 2 seconds.
4. Connect the drive to the power supply again. The drive clicks.
5. Press the PAIR key on a hand-held transmitter that has already been programmed for at
least 7 seconds. The drive clicks once after approx. 2 sec. and a second time after approx.
7 sec., the drive is reset to the delivery state.
11. Copyinghand-heldtransmitterswithoutadrive
It is possible to copy the functions of a hand-held transmitter
(master hand-held transmitter) to a new hand-held transmitter.
The procedure must be carried out separately for each key.
Makethenewhand-heldtransmitterreadytoreceive.
1. Remove the bottom shell of the new hand-held transmitter.
Press the PAIR key with a paper clip or similar of the new
hand-held transmitter (A). The LED starts ashing.
2. Press the UP key on the new hand-held transmitter (A) within
4 seconds and keep it pressed. The LED starts to light up
permanently.
Transferringthekeytothenewhand-heldtransmitter
3. Continue to hold down the key on the new hand-held transmit-
ter (A) and align the fronts of the two hand-held transmitters
(distance max. 5 mm).
4. Press the UP key on the master hand-held transmitter (B). As
soon as the LED on the new hand-held transmitter (A) turns
darker, the copying of the UP key is nished and you can
release both keys.
RepeattheprocesswiththeSTOPandDOWNkeys.
0 ... 5 mm
1
2
4
3
(A)
(A)
(A)
(A
)(
B)

5
www.geiger.de EN
EN
12. Resettingthehand-heldtransmittertothedeliverystate
To reset the hand-held transmitter to the delivery state, press the PAIR key for at least
30 seconds.
After 10 seconds, the status LED begins to ash quickly, after 20 seconds the status LED starts
to ash slowly and after 30 seconds the status LED turns off. The hand-held transmitter is reset
to the factory settings.
13. Changing the batteries
Replace the batteries as soon as the status LED no longer lights up when an operating key is
pressed. See chapter „Insert batteries“.
14. Technical data
Transmittingfrequency 433,92 MHz
Transmission power 6 dBm
Temperature range -0°C to +60°C
Protection class IP20
Batteries 2x LR03, Typ AAA
Dimensions 95 x 42 x 20 mm
Subject to technical modifications
15. Declarationofconformity
We herewith explicitly declare that this product complies with the essential requirements
and relevant directives. It is authorised for use in all EC member states and in Switzerland
without any need of prior registration. The Declaration of Conformity concerning this product is
available on our website: www.geiger.de
16. Disposal information
Disposal of packaging materials
Packaging materials are raw materials and can therefore be reused. In the interest of environ-
mental protection, please dispose of them properly.
Disposalofelectricalandelectronicequipment
According to the EU Directive, electrical and electronic equipment must be collected and
disposed of separately.

6Gerhard Geiger GmbH & Co. KG | 100W1650 1121V000en
EN
EN

7
www.geiger.de EN
EN

8Gerhard Geiger GmbH & Co. KG | 100W1650 1121V000en
EN
EN
For technical questions, please call our service team at: [phone].
They will be happy to assist you.
Gerhard Geiger GmbH & Co. KG
Schleifmühle 6 | D-74321 Bietigheim-Bissingen
T [phone] | F [phone]
[e-mail] | www.geiger.de