GEIGER GF25 Series User manual

1
www.geiger.de EN
EN
DE Original-Montage- und
Betriebsanleitung
Original assembly and
operating instructions
Notice originale de montage
et d’utilisation
Instrucciones originales de
instalación y funcionamiento
Istruzioni originali di installazione
e funzionamento
EN
FR
ES
IT
123 456
Wall-mounted radio transmitters
GF25..
Wandsender
Wall-mounted radio transmitters
Télécommandes murales

2Gerhard Geiger GmbH & Co. KG | 100W1610 0315V000en
EN
EN
Index
1. General information..................................................................2
2. Guarantee ..................................................................................2
3. Walltransmitterspecicsafetyinformation ..........................2
4. Scopeofdelivery ......................................................................2
5. GF25../Assignmentofkeys ....................................................3
6. Wall transmitter coding ............................................................3
7. Programming a wall transmitter to a GEIGER motor
or an external radio receiver....................................................3
8. Programming the sun automatic function to a GEIGER
motor or an external radio receiver.........................................4
9. Sun automatic ...........................................................................4
10. Createawalltransmittercopy.................................................4
11. Batteryreplacement .................................................................5
12. Assembly ...................................................................................5
13. Technical data ...........................................................................5
14. Declarationofconformity ........................................................5
15. Disposal .....................................................................................5
1. General information
Dear customer,
By purchasing a GEIGER radio-controlled wall transmitter you have decided on a quality
product from GEIGER.
Thank you very much for your decision and the condence placed in us.
2. Guarantee
In the case of incorrect installation contrary to the operating instructions and/or constructional
modication, the legal and contractual guarantee for property damage and product liability
lapses.
3. Walltransmitterspecicsafetyinformation
Please observe following instructions in order to avoid damage to this product:
fAvoid impacts
fDo not drop the device
fDonotimmerseinwateroranyliquid.Ensureprotectionagainstsplashingwater.
fNever use cleaning agents or abrasive solvents. Clean the surface of the transmitter
with a damp cloth.
4. Scopeofdelivery
• Wall transmitter
• Adhesive pad
• Mounting screws and plugs
• Battery type button cell CR2032 (inserted)
• Operating instructions

3
www.geiger.de EN
EN
5. GF25../Assignmentofkeys
Channel display:
1 channel wall transmitter
2 or 6 channel wall transmitter
123456
Sun automatic function ON / OFF
(only 2 or 6 channel wall transmitter)
UP key
STOP key
DOWN key
Channel selection keys
(only 2 and 6 channel)
6. Wall transmitter coding
Each wall transmitter of the series GF25.. is individually coded.
The coding is done via a coding switch in the wall transmitter. It should only be changed in
exceptional cases. (see “Create a wall transmitter copy“).
7. Programming a wall transmitter to a GEIGER motor or
an external radio receiver
1. Select the desired channel with the channel selection
keys ( ).
2. Connect the motor to the mains power supply.
The motor makes a short back and forth movement
(1x click-click).
Aftereachinterruptionofthepowersupplythe
programming mode can be activated for
30 minutes.
3. Hold the wall transmitter with the bottom side to the
power cable and press the UP ( ) or DOWN key ( )
for about 3 seconds until the motor conrms with an
audible signal (1x click-click).
4. Hold again the wall transmitter to the power cable and
press UP ( ) or DOWN key ( ) for 1 second.
The motor conrms again (1 x click–click).
Repeat these steps for each desired channel.
I Please refer to the operating
instructions of the respective motor
or receiver for further information
or for the adjustment.
123 456
230 V
On
Off
connect to
mains
1 x “click-click“
max. 15 cm
click-
clack
123 456
or
about 3 sec.
1 x
max. 15 cm
click-
clack
123 456
or
about 1 sec.
1 x

4Gerhard Geiger GmbH & Co. KG | 100W1610 0315V000en
EN
EN
8. Programming the sun automatic function to a GEIGER
motor or an external radio receiver
I The operation is to be performed during the 30 minutes after the
powersupplyhasbeenswitchedon.
1. Select the sun automatic channel ( ) with the channel
selection keys ( )
2. In the near range press the UP ( ) or DOWN key ( )
for about 3 seconds until the motor conrms with an
audible signal (1x click-click).
3. Hold the wall transmitter with the bottom side to the
power cable and press the UP ( ) or DOWN key ( )
for 1 second. The motor conrms with an audible signal
(1x click-click).
Then program the wall transmitter in the GEIGER sun/
wind sensor.
4. Hold the bottom side of the wall transmitter on the left
side of the sun/wind sensor, press the UP or DOWN
key – the sun icon of the wall transmitter lights up –
until the red LED of the sun/wind sensor lights up.
9. Sun automatic
To enable / disable the automatic sun function, press the channel selection keys ( )
until the sun icon ( ) lights up.
The sun automatic function is activated with the UP key ( ) and deactivated with the
DOWN key ( ).
10. Createawalltransmittercopy
If you want to create a copy of your wall transmitter with all its
functions (e.g. two identical wall transmitters for two persons),
please proceed as follows:
1. Move both wall transmitters out of theirs holders.
2. Use the same coding on the second transmitter (copy) as the
original one. The keys 7, 8 and 9 are not modied.
3. Put the wall transmitters back on theirs supports.
Thisprocessallowsyoutocreateanunlimitednumberof
copies of the original wall transmitter.
230 V
On
Off
connect to
mains
1 x “click-click“
max. 15 cm
click-
clack
123 456
or
about 3 sec.
1 x
max. 15 cm
click-
clack
123 456
or
about 1 sec.
1 x
23 4561 23 4561
1
+
0
-
23456789
CR2032
Individual
coding
Channel
selection

5
www.geiger.de EN
EN
11. Batteryreplacement
If the display doesn‘t light up if actuating one of the control keys, the batteries need to be
replaced. In this case please remove the wall transmitter out of the holder. Make sure that you
use the same type of battery (CR2032). Then put the wall transmitter back on its holder.
12. Assembly
Three options are available for assembling the bottom part
of the wall transmitter:
1 Adhesive xing with adhesive pad (encl.)
2 Wall mounting with 2 screws (dowels and screws
enclosed)
3 Screw mounting on a ush mounting box
13. Technical data
Transmittingfrequency 433,92 MHz
Temperature range between -0°C and +60°C
Dimensions 81 x 81 x 14,3 mm
Powersupply 3V Typ CR2032
Subject to technical modifications DE
V
geprüfte
Sicherheit
14. Declarationofconformity
The wall transmitter complies with the relevant technical regulations enacted by the European
Community. It bears the CE mark and is authorised for use in all EU member states and in
Switzerland without any need of prior registration.
To learn more about the EC Declaration of Conformity pertaining to this wall transmitter, please
visit our website at: www.geiger.de
15. Disposal
Recyclingofpackagingmaterials
In the interest of environmental protection, please contact your local government’s recycling or
solid waste management department to learn more about the services it provides.
Wastedisposalofelectricandelectronicequipment.
Electronic equipment or batteries cannot be discarded along with the normal household waste.
Keep for more information on the recycling and disposal methods envisaged by the local
regulations in your area.




6Gerhard Geiger GmbH & Co. KG | 100W1610 0315V000en
EN
EN
For technical questions, please call our service team at: [phone].
They will be happy to assist you.
Gerhard Geiger GmbH & Co. KG
Schleifmühle 6
D-74321 Bietigheim-Bissingen
Telephone: [phone]
Telefax: [phone]
E-Mail: [e-mail]
Internet: www.geiger.de