GEIGER LC AIR GF280 Series User manual
1
www.geiger.de EN
EN
DE Original-Montage- und
Betriebsanleitung
Original assembly and
operating instructions
Notice originale de montage
et d’utilisation
Instrucciones originales de
instalación y funcionamiento
Istruzioni originali di installazione
e funzionamento
EN
FR
ES
IT
123 456
Wall-mounted radio transmitters
LC AIR GF280.
2Gerhard Geiger GmbH & Co. KG | 100W1619 0221V000en
EN
EN
1. General information
Dear customer,
By purchasing a GEIGER radio-controlled wall transmitter you have decided on a quality
product from GEIGER.
Thank you very much for your decision and the condence placed in us.
2. Guarantee
In the case of incorrect installation contrary to the operating instructions and/or constructional
modication, the legal and contractual guarantee for property damage and product liability lapses.
3. Wall transmitter specic safety information
Please observe following instructions in order to avoid damage to this product:
fAvoid impacts
fDo not drop the device
fDo not immerse in water or any liquid. Ensure protection against splashing water.
fNever use cleaning agents or abrasive solvents. Clean the surface of the transmitter
with a damp cloth.
4. Scope of delivery
• Wall transmitter
• Adhesive pad
• Mounting screws and plugs
• Battery type button cell CR2032 (inserted)
• Operating instructions
5. Radio transmitters LC AIR / Assignment of keys
Channel display
123456
Sun automatic function ON / OFF
(only 2 or 6 channel wall transmitter)
UP key
STOP key
DOWN key
Channel selection keys
(only 2 and 6 channel)
6. Learning a wall transmitter on a GEIGER motor
Please refer to the operating instructions of the motor for the learning of the wall transmitter on
the motor and the setting of the end stops.
7. Switch the automatic sun function on and off
To switch the sun automatic function on and off, please refer to the operating instructions of the
weather station AIR.
123 456
3
www.geiger.de EN
EN
8. Connect the GEIGER Remote LC AIR to your Miniserver
Requirements
To integrate the GEIGER Remote LC AIR into your Loxone system, a Miniserver Go or a
Miniserver with Air Base Extension is necessary. Here you can nd more information on this
topic: www.loxone.com/help/miniserver
Commissioning in Loxone Cong
To connect the GEIGER Remote LC AIR to
your Miniserver, the device has to be set in
the Loxone Mode and afterwards the learning
mode has to be started.
To do so, remove the battery and set the switch
on the circuit board inside the unit on „LX“.
Once the battery is inserted again, the learning
mode will start automatically.
In order to learn in the GEIGER Remote LC
AIR you need to connect to your Miniserver
and activate the Air Monitor. Click on the Air
Base Extension in the periphery window and
then check the tick box ‚Monitor‘ in the context
bar at the top.
Next, click on the learn tab in the monitor below
and then click the „Start search“ button. Now
you will see all the Air devices that are in the
learning mode below.
Now highlight the device, enter a name for it
and then click ‚Create device‘.
The device can now be seen in the periphery
tree underneath the Air Base Extension.
More information: www.loxone.com/help/lcair
Please note!
When switching from the GG mode to the LX
mode, the 6-channel transmitter turns into a
1-channel transmitter. The inputs in the Loxone
Cong are assigned as follows:
Input 1: OPEN button
Input 2: LEFT button
Input 3: STOP button
Input 4: RIGHT button
Input 5: DOWN button
1
3
24
5
4Gerhard Geiger GmbH & Co. KG | 100W1619 0221V000en
EN
EN
For technical questions, please call our service team at: +49 (0) 7142 938 333.
They will be happy to assist you.
Gerhard Geiger GmbH & Co. KG
Schleifmühle 6 | D-74321 Bietigheim-Bissingen
T +49 (0) 7142 9380 | F +49 (0) 7142 938 230
info@geiger.de | www.geiger.de
9. Battery replacement
If the display doesn‘t light up if actuating one of the control keys, the batteries need to be
replaced. In this case please remove the wall transmitter out of the holder. Make sure that you
use the same type of battery (CR2032). Then put the wall transmitter back on its holder.
10. Assembly
Three options are available for assembling the bottom part
of the wall transmitter:
1 Adhesive xing with adhesive pad (encl.)
2 Wall mounting with 2 screws (dowels and screws
enclosed)
3 Screw mounting on a ush mounting box
11. Technical data
Transmitting frequency 868 MHz
Temperature range between -0°C and +60°C
Dimensions 81 x 81 x 14,3 mm
Power supply 3V Typ CR2032
Subject to technical modifications DE
V
geprüfte
Sicherheit
12. Declaration of conformity
The wall transmitter complies with the relevant technical regulations enacted by the European
Community. It bears the CE mark and is authorised for use in all EU member states and in
Switzerland without any need of prior registration.
To learn more about the EC Declaration of Conformity pertaining to this wall transmitter, please
visit our website at: www.geiger.de
13. Disposal
Recycling of packaging materials
In the interest of environmental protection, please contact your local government’s recycling or
solid waste management department to learn more about the services it provides.
Waste disposal of electric and electronic equipment.
Electronic equipment or batteries cannot be discarded along with the normal household waste.
Keep for more information on the recycling and disposal methods envisaged by the local
regulations in your area.
Table of contents
Other GEIGER Transmitter manuals
