Genie UKP-EM User manual

Please read these instructions carefully before operating the unit
and keep for further reference.
User Manual
IP67 125KHz Universal
Multi-Function Keypad and
Proximity Reader
UKP-EM

QTY
1
1
1
4
4
1
2
Manager Add & Manager Delete
Self Tapping Screws
1N4007 Diode
Manager Cards
4 x 28mm
6 x 27mm for wall fixing
4. Specification
ITEM
REMARKS
Digital Keypad - UKP-EM
User Manual
1. Packing List
Secure Torx Screwdriver
Wall Plugs
Please ensure all the above contents are correct. If any are missing, please notify your supplier.
2. Description
The UKP-EM is a dual-relay access control keypad with EM & HID 125 KHz built in card reader. It is suitable for mounting either
indoor, or outdoor in harsh environments. It 's housed in a strong, sturdy and vandal resistant, zinc alloy, electroplated case. The
electronics are fully potted so the UKP-EM is waterproof and conforms to IP67.
The UKP-EM supports up to 2,100 Card Users, 4~8 digit PIN, Card + PIN option and additional 10 groups Duress PIN/Card. The built-
in Card Reader supports both EM & HID 125 KHz frequency Cards/Tags. The UKP-EM has many extra features including Duress PIN/
Card, Block Enrollment, Wiegand 26~37 bit Interface, and backlit Keypad…etc.
These features make UKP-EM an ideal choice for door access not only for small shops and domestic households, but also for
commercial and industrial applications such as factories, warehouses, laboratories, banks and prisons.
3. Features
• Water Resistant, conforms to IP67
• Strong zinc alloy electroplated anti-vandal case
• Two relay operation
• 2,100 users & 10 groups for duress PIN/Card
• Zone 1: up to 2,000 PIN & card holders
• Zone 2: up to 100 PIN & card holders
• Both Relay Zones can be programmed for 3 modes: Card, PIN, Card + PIN for Stand alone mode
PLEASE NOTE:
• For Wiegand mode the keypad can be used for EITHER Card OR Pin – NOT both.
• Wiegand data is sent on a first come first send basis: if you show the card and then the pin,
the keypad will transmit the card ID immediately and then the pin number as a Wiegand ID straight after that.
For this reason Card & Pin are not relevant in Wiegand mode – only useful in standalone mode.
• In Wiegand mode, PIN number = Wiegand ID that your 3rd party controller will see.
• Reads both EM & HID 125KHz cards
• PIN length 4~8 digits
• Pulse mode or Toggle mode options
• Wiegand 26~37 input & output
• Can operate as a reader or controller
• Dual relay outputs for door opening, door status detection, exit button connection
• Card block enrolment
• Manager cards for individually adding or deleting card users (Zone 1)
• Low power consumption（25mA）
• Blue Back Lit Keypad
• Back Light and Keypad tone can be disabled
• Supports door bell connection (Zone 2)
• Built in light dependent resistor (LDR) for anti tamper
• Built in buzzer
• Red, yellow, green and blue status LED
• DC12~24V or AC12~18V
• Two-year warranty

Adjustable Door Relay Time
Active Current Draw
≥60mA
700g
-20° to +60°C
Operating Temperature
Dimensions
Wiegand Interface
Wiegand 26 or 37 Bit Input & Output
Wiring Connections
Adjustable Alarm Time
0 - 3 Minutes
Electric Lock, Exit Button, DOTL, External Alarm
Operating Humidity
10% - 90% RH
Environmental Rating
IP67
1 - 99 Seconds
600g
Gross Weight
L128 X W82 X H28 mm
5. Installation
Idle Current Draw
≥25mA
Lock Relay Output Load
Max 2A
Alarm Relay Output Load
Max 20A
Net Weight
3 - 6 Cm
Keypad
12 Keys, 3 x 4 Digits
4. Specification
DC12-24V Or AC12-18V
RF Card Reading Distance
Card Type
EM & HID 125 KHz Cards / Fobs
User Capacity
Operating Voltage
2100 & 10 Additional groups for duress- PIN/Card
• Remove the back cover from the keypad using the supplied security screwdriver
• Drill 4 holes on the wall for the screws and 1 hole for the cable
• Fix the back cover firmly on the wall with 4 flat head screws
• Thread the cable through the cable hole
• Attach the keypad to the back cover

FUNCTION
NC 1
COM 1
NO 1
NC 2
COM 2
NO 2
AC & DC +
AC & DC -
D_IN
OPEN 1
OPEN 2
ALARM
D1
D0
GROUND
Connection Diagrams
White
Green
Black
Brown
Yellow
Yellow & Black
Grey
WIEGAND INPUT/OUTPUT D1
WIEGAND INPUT/OUTPUT D0
Black & White
Pink
Red
Red & Black
Orange
Purple
Blue
Green & Black
NEGATIVE / GROUND / EARTH
DOOR CONTACT
REQUEST TO EXIT BUTTON FOR ZONE 1
REQUEST TO EXIT BUTTON FOR ZONE 2
ALARM NEGATIVE
RELAY 2 COMMON
RELAY 2 NORMALLY OPEN
DC12-24V Or AC12-18V REGULATED INPUT
DC12-24V Or AC12-18V REGULATED INPUT
RELAY 1 - NORMALLY CLOSED
RELAY 1 COMMON
RELAY 1 NORMALLY OPEN
RELAY 2 - NORMALLY CLOSED
6. Wiring Guide
DESCRIPTION
COLOUR

BLUE LED
-
ON
-
-
-
-
-
-
-
-
-
10. UKP-EM Detailed Programming Guide
LONG BEEP
ALARM
FLASHING
-
-
ALARM
EXIT PROGRAMMING MODE
FLASHING
-
-
LONG BEEP
IN PROGRAMMING MODE
ON
-
ON
ENTER PROGRAMMING MODE
ON
-
LONG BEEP
OPERATION FAILED
FLASHING
-
-
3 SHORT BEEPS
SUCCESSFUL OPERATION
-
ON
-
KEY PRESS
FLASHING
-
-
SHORT BEEP
STAND BY
FLASHING
OFF
-
SHORT BEEP
POWER ON
ON
-
-
LONG BEEP
ZONE 2 UNLOCK
-
-
-
BUZZER
ZONE 1 UNLOCK
-
ON
-
SHORT BEEP
8. Anti Tamper Alarm
9. Sound & LED Indication
OPERATION
RED LED
GREEN LED
AMBER LED
7. Relay Operation - (Pulse and Toggle Mode)
Both relays on board operate in Pulse Mode (suitable for access control) or
Toggle Mode (suitable for arming/disarming alarms, switching lights, machines….etc)
In Pulse Mode: every time a valid Tag/Card or PIN is read/input, the relay operates for the pre-set relay pulse time.
In Toggle Mode: every time a valid Tag/Card or PIN is read/input, the relay changes state, which will not turn back until the user
presents a valid card or pin number again.
The UKP-EM uses a LDR (light dependent resistor) as an anti tamper alarm. If the keypad is removed from the cover, the tamper
alarm will operate.
• To Reset to Factory Default
To reset to factory default, please follow the following steps :
1. Power Off
2. Press & hold and power On
3. Release it when you hear two beeps and the LED goes orange
4. Read two EM or HID cards, the LED will turn red, which means the keypad has successfully been reset to the factory default
setting.
5. Of the two cards read, the first one is Manager Add Card, the second one is Manager Delete Card.
Remarks: When you reset to factory default, the user’s information is still retained.
*

RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
KEY PRESS 1 KEY PRESS 3
OPERATIONAL MODE SELECTOR
0
1
2
3
4
5
6
7
8
9
RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
10.3 MASTER CODE SETTINGS
SETTING
STEPS
-
1 BEEP
1 BEEP
TO ENTER PROGRAMMING MODE
PRESS
FLASHING
-
ON
-
BEFORE YOU START
OBSERVE KEYPAD STATUS
OUT THE BOX
ENTER
ON
6 BEEPS
-
PRESS
ON
SHORT FLASH
MASTER CODE CHANGE
DELETE USERS
ID MODE SELECTION
PULSE / TOGGLE SELECTOR
HOW TO CHANGE MASTER CODE
SETTING
STEPS
ON
-
6 BEEPS
6 BEEPS
PRESS
ON
-
1 BEEP
FLASHING
-
PRESS
ON
SHORT FLASH
1 BEEP
1 BEEP
ENTER PROGRAMMING MODE
USING DEFAULT MASTER CODE
PRESS
ON
ON
RE- ENTER
ON
-
ON
ENTER
1 BEEP
ON
1 BEEP
10.1 USER SETTINGS
10.2 KEY PRESS OPERATION & PROGRAMMING MENU EXPLANATION GUIDE
KEY PRESS 2
ZONE SELECTOR
MENU FUNCTION SELECT
1 BEEP
PLEASE NOTE: MASTER CODE IS REQUIRED FOR ALL PROGRAMMING FUNCTIONS AND MENUS.
TO EXIT PROGRAMMING MODE
PRESS
FLASHING
ALARM OUTPUT TIME
DOOR OPEN DETECTION SETTINGS
LOCK & ALARM OUTPUT SETTINGS
L.E.D & BUZZER SETTINGS
TO EXIT PROGRAMMING MODE
PRESS
WIEGAND FORMAT SELECTOR
-
-
-
-
-
ADDING USERS
*
888 888 (DEFAULT MASTER CODE)
#
*
. . . . . . (NEW 6 DIGIT CODE)
#
*
0
(NEW 6 DIGIT CODE)
#
0 - 9 1 OR 2 1 / 2 / 0
CARD & PIN MODE
CAR OR PIN MODE
CARD ONLY
RELAY / ZONE 2
RELAY / ZONE 1
PLEASE NOTE:
If a Card user has already been enrolled , the keypad will not allow you to duplicate by enroling it, again. You will get an error tone.
You can however enrol the same pin number for both Zones, but this only operates relay 1

RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
ON AFTER SHORT FLASH ON AFTER
#AFTER # AFTER 3 - 1
ON AFTER SHORT FLASH ON AFTER
#AFTER # AFTER 3 - 1
ON AFTER SHORT FLASH ON AFTER
#AFTER # AFTER 3 - 1
ON AFTER SHORT FLASH ON AFTER
#AFTER # AFTER 3 - 1
ON AFTER SHORT FLASH ON AFTER
#AFTER # AFTER 3 - 1
ON AFTER SHORT FLASH ON AFTER
#AFTER # AFTER 3 - 1
RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
E.G.
SETTING
STEPS
PRESS
1 BEEP / KEY
PRESS
1 BEEP / KEY
ON
FLASHING
-
-
1 BEEP / KEY
SHORT FLASH
ON
1 BEEP
USING MASTER CODE
10.4 SETTING OPERATIONAL MODES
1 BEEP / KEY
ENTER PROGRAMMING MODE
ON
SHORT FLASH
1 BEEP / KEY
CARD AND PIN MODE
1 BEEP / KEY
PRESS
1 BEEP / KEY
CARD OR PIN MODE (DEFAULT SETTING)
1 BEEP / KEY
PRESS
1 BEEP / KEY
PRESS
1 BEEP / KEY
PRESS
1 BEEP / KEY
PRESS
1 BEEP
SETTING OPERATIONAL MODE
ENTER PROGRAMMING MODE
ON
-
1 BEEP / KEY
USING MASTER CODE
OR
PRESS
TO EXIT PROGRAMMING MODE
-
PRESS
FLASHING
-
ON
ON
-
FOR RELAY 1
SETTING
STEPS
SETTING
STEPS
OR
CARD ONLY
OR
10.5 ADDING AND DELETING PIN NUMBERS
PIN= ANY 4-8 DIGITS BETWEEN 0000-99999999
CANNOT USE PIN 1234 - THIS IS RESERVED
-
-
-
-
USER ID = 4 DIGITS 1-2000 FOR RELAY 1
ENTER USER ID (1 - 2000) &
ADDING A PIN NUMBER - TO RELAY
ENTER PIN NUMBER &
-
-
ENTER PROGRAMMING MODE
ON
SHORT FLASH
ADDING A PIN NUMBER - TO RELAY
FOR RELAY 2
-
-
-
1 BEEP
USING MASTER CODE
ON
1 BEEP / KEY
ON
CANNOT USE PIN 1234 - THIS IS RESERVED
USER ID = 4 DIGITS 2001 - 2100 FOR RELAY 2
PIN= ANY 4-8 DIGITS BETWEEN 0000-99999999
ENTER PIN NUMBER &
-
SHORT FLASH
ENTER USER ID (2001-2100) &
-
-
1 BEEP / KEY
PRESS
ON
-
1 BEEP / KEY
ON
1 BEEP / KEY
PLEASE NOTE:
USERS CAN BE ADDED CONTINUOUSLY WITHOUT HAVING TO EXIT THE PROGRAMMING MODE
Etc, Etc…
-
1 BEEP / KEY
PRESS
FLASHING
-
3 2 2
3
1
2
FOR RELAY 1
3 2 1
3
1
1
3 2 0
3
1
0
*
FOR RELAY 2
FOR RELAY 2
FOR RELAY 1
#
#
#
#
#
#
FOR RELAY 1
FOR RELAY 2
1
1
AGAIN TO EXIT
#
#
*
*
1
2
AGAIN TO EXIT
#
#
*
*
2
1
1 1 USER ID 1 # PIN NUMBER 1 # USER ID 2 # PIN NUMBER 2 #

RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
1 BEEP / KEY
USERS MAY BE DELETED CONTINUOUSLY WITHOUT EXITING THE PROGRAMMING MODE
PRESS
FLASHING
-
-
-
ON
1 BEEP / KEY
-
1 BEEP / KEY
SHORT FLASH
1 BEEP
USING MASTER CODE
1 BEEP / KEY
-
ON
SHORT FLASH
SETTING
STEPS
ENTER PROGRAMMING MODE
ON
ON
TO DELETE A PIN NUMBER
FLASHING
PRESS
SETTING
STEPS
TO CHANGE AN EXISTING PIN NUMBER
PLEASE NOTE: THESE STEPS ARE DONE
OUTSIDE OF THE PROGRAMMING MODE
FLASHING
-
-
1 BEEP / KEY
PRESS FOLLOWED BY:
ON
-
ON
-
FLASHING
-
-
1 BEEP / KEY
OUT OF PROGRAMMING MODE
-
1 BEEP / KEY
-
1 BEEP / KEY
1 BEEP / KEY
10.6 ADDING AND DELETING CARD USERS - 4 METHODS
SHORT FLASH
-
1 BEEP
SETTING
STEPS
SETTING
STEPS
ADDING CARDS VIA MANAGER CARD
PRESENT USER CARD / S
-
METHOD 2 - AUTO ID
ON
ON
ON
1 BEEP / KEY
PRESENT CARD TO FINISH
FLASHING
-
1 BEEP / KEY
SHORT FLASH
1 BEEP / KEY
PRESENT CARD TO START
PRESENT USER CARD / S TO BE DELETED
-
SHORT FLASH
1 BEEP / KEY
METHOD 1 - MANAGER CARDS
PRESENT CARD TO START
ON
DELETING CARDS VIA MANAGER CARD
PRESENT CARD TO FINISH
FLASHING
-
1 BEEP
-
-
ON
1 BEEP / KEY
ENTER PROGRAMMING MODE
USING MASTER CODE
PRESENT &
ON
SHORT FLASH
VALID FOR RELAY ONE ONLY !!!
ADDING CARDS VIA AUTO ID GENERATOR
ADVISABLE TO MAKE A NOTE OF THE CARD NOS.
CARDS MAY BE ADDED CONTINUOUSLY WITHOUT HAVING TO EXIT THE PROGRAMMING MODE.
SHORT FLASH
1 BEEP
FOR RELAY 1
AS A CARD IS ADDED, IT IS AUTOMATICALLY ALLOCATED AN ID. CLOSES PROGRAMMING
FOR RELAY 2
-
-
ON
1 BEEP / KEY
PRESS TO EXIT
FLASHING
1 BEEP
ON
1 BEEP / KEY
ENTER PROGRAMMING MODE
USING MASTER CODE
DELETING CARDS VIA CARD NUMBER
ON
SHORT FLASH
PRESS TWICE TO EXIT
FLASHING
1 BEEP / KEY
TO CONFIRM
SHORT FLASH
ON
2
0
AGAIN TO EXIT
*
*
USER ID LOCATION
#
MANAGER ADD
USER ID LOCATION
#
*
OLD PIN NUMBER
#
NEW PIN NUMBER
#
NEW PIN NUMBER
#
MANAGER ADD
MANAGER DELETE
MANAGER DELETE
1
1
USER CARD / S
#
#
1
2
*
2
0
CARD NUMBER
#
*

RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
ON - - 1 BEEP / KEY
FLASHING - - -
1 BEEP / KEY
FLASHING - - -
RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
- - 1 BEEP / KEY
FLASHING - - -
ON - - 1 BEEP / KEY
FLASHING - - -
RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
- - 1 BEEP / KEY
TO CONFIRM
ON
DELETE ALL RLY 1 USERS
DELETE ALL RLY 2 USERS
1 BEEP / KEY
-
SHORT FLASH
ON
1 BEEP / KEY
-
SHORT FLASH
ON
1 BEEP
SHORT FLASH
ON
1 BEEP / KEY
SHORT FLASH
USING MASTER CODE
DELETE ALL USERS
-
ADDING CARDS VIA BLOCK ENROLMENT
ENTER PROGRAMMING MODE
ON
10.7 TO DELETE ALL USERS
DELETING ALL USERS
SETTING
STEPS
PRESS TO EXIT
ON
ON
ON
ON
SHORT FLASH
-
ON
ON
SHORT FLASH
1 BEEP / KEY
TO CONFIRM
NEED CARD OR SHADOW CARD PRESENT
SHORT FLASH
1 BEEP
USING MASTER CODE
TO CONFIRM
PRESS TO EXIT
DELETING CARDS VIA EXISTING CARD
ENTER PROGRAMMING MODE
1 BEEP / KEY
(BETWEEN 1-2000)
-
SHORT FLASH
ON
1 BEEP / KEY
SEQUENCE
-
1 BEEP
USING MASTER CODE
FOR USE ON RELAY 1 ONLY
-
-
ON
1 BEEP / KEY
ADDING CARDS IN BATCHES
ENTER PROGRAMMING MODE
PRESS TO EXIT
METHOD 4 - BLOCK ENROLMENT
SETTING
STEPS
FOR RLY 1
1 BEEP
USING MASTER CODE
ADDING CARDS VIA MANUAL ID INPUT
METHOD 3 - MANUAL ID ALLOCATION
SETTING
STEPS
1 BEEP / KEY
-
SHORT FLASH
ON
-
-
ON
1 BEEP / KEY
ON
ENTER PROGRAMMING MODE
ON
SHORT FLASH
1 BEEP / KEY
1 BEEP
PRESS TO EXIT
FOR RLY 2
-
-
TO CONFIRM
SHORT FLASH
DELETING CARDS VIA USER ID
ENTER PROGRAMMING MODE
USING MASTER CODE
ON
ON
1 BEEP / KEY
TO CONFIRM
E.G.: IF A CARD IS LOST OR STOLEN
SHORT FLASH
READ CARD #
*
#
1
2
USER ID (2001-2100)
#
1
1
USER ID (1-2000)
#
2
0
ENTER USER ID NO.
#
*
CARD QUANTITY
*
#
NUMBER OF FIRST CARD #
1
0
USER ID (1-2000)
#
2 0 READ CARD NO.
#
*
#
2
0
0000
#
2
1
0000
#
2
2
0000
#

RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
- - 1 BEEP / KEY
- - -
- -
- - -
RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
HIGH PITCH
BEEP
-
- - -
1 BEEP / KEY
1 BEEP / KEY
ON
NOTE: TO DELETE A CARD AND PIN USER, JUST DELETE THE CARD AS PER SECTION: 10.6 METHODS 1,2,3 OR 4
-
-
-
OUTSIDE PROGRAMMING MODE
-
-
ON
METHOD 2 - VIA USER ID
OUTSIDE PROGRAMMING MODE
-
SHORT FLASH
ON
-
-
-
STEPS
-
-
-
1 BEEP / KEY
METHOD 1 - VIA CARD
-
-
ON
SHORT FLASH
REPEAT
ON
10.9 CHANGING A PIN NUMBER IN CARD AND PIN MODE
CHANGING A CARD'S PIN NUMBER
SETTING
ON
ADD A CARD AS FOR A CARD USER (10.6)
THEN ALLOCATE CARD PIN AS FOLLOWS
PIN IS ANY 4-8 DIGITS LONG
ON
ON
1 BEEP / KEY
PRESS TO EXIT PROGRAMMING
-
SHORT FLASH
ON
1 BEEP / KEY
FOR RLY 2
-
-
ON
SET CARD AND PIN MODE AS PER SEC (10.4)
FOR RLY 1
-
-
ON
1 BEEP / KEY
SHORT FLASH
ALLOCATING PIN NUMBER TO CARD
SETTING
STEPS
1 BEEP
USING MASTER CODE
ADDING CARDS VIA BLOCK ENROLMENT
ENTER PROGRAMMING MODE
10.8 ALLOCATING A PIN NUMBER TO A CARD USER (FOR CARD AND PIN USE)
3
0
#
1
1
3
0
#
2
1
*
*
READ CARD 1234 #
PIN #
PIN #
*
READ CARD OLD PIN #
NEW PIN # NEW PIN
#
*
USER ID NO. OLD PIN
#
NEW PIN # NEW PIN
#
#

RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
- 1 BEEP / KEY
FLASHING - - -
RED GREEN AMBER BUZZER
LED STATUS LED STATUS LED STATUS STATUS
- 1 BEEP / KEY
FLASHING - - -
ON
1 BEEP / KEY
SET RELAY TIMINGS
FOR RELAY 1
ON
1 BEEP / KEY
ENTER PROGRAMMING MODE
USING MASTER CODE
ON
SHORT FLASH
SETTING PULSE MODE (DEFAULT)
SETTING
STEPS
FOR CARD USER
FOR CARD AND PIN USER
JUST READ THE CARD
READ CARD, FOLLOWED BY PIN AND
FOR PIN USER
ENTER FOLLOWED BY
11. Door Operation - (Gaining Access)
SETTING TOGGLE MODE
(RELAY TIME IS 1~ 99 SEC.)
1 BEEP / KEY
1 BEEP / KEY
PRESS TO EXIT
11.2 Relay Settings (Toggle Mode)
TO CONFIRM
ON
SHORT FLASH
FOR RELAY 2
SETTING
STEPS
ENTER PROGRAMMING MODE
ON
SHORT FLASH
1 BEEP / KEY
USING MASTER CODE
ON
1 BEEP / KEY
FOR RELAY 2
1 BEEP / KEY
SET RELAY TIMINGS
PRESS TO EXIT
11.1 Relay Settings (Pulse Mode / Toggle Mode)
12. DOOR SENSORS, ALARMS, SOUND & LED SETTINGS
TO CONFIRM
ON
SHORT FLASH
FOR RELAY 1
ON
PIN NO. #
#
4
1
1 ~ 99
4
2
#
*
4
1
4
2
#
*
0
0
Door Open Detection
Door Open Too Long (DOTL) warning.
Used with an optional magnetic contact or built-in magnetic contact in the lock.
If the door is opened normally, but not closed after 1 minute, the inside buzzer will beep automatically as a reminder to close the door and continues for 1 minute
before switching off automatically.
Door Forced Open Warning
Used with an optional magnetic contact or built-in magnetic contact in the lock.
If the door is opened by force, or if the door is opened after 120 seconds of the electro-mechanical lock not closing properly, the inside buzzer and alarm output
will both operate.
The Alarm Output time is adjustable between 0~3 minutes, with the default being 1 minute.
Please see options below for settings:

TO DISABLE DOOR OPEN DETECTION (DEFAULT)
**THE FOLLOWING FUNCTIONS ARE ALL PERFORMED IN PROGRAMMING MODE**
12. 1 DOOR SENSORS DETECTION - SETTING
TO DISABLE DOOR OPEN DETECTION (DEFAULT)
*PLEASE NOTE, IMPORTANT*
DEFAULT: NO KEYPAD LOCKOUT OR ALARM
KEYPAD LOCKOUT ENABLE
TO EXIT PROGRAMMING
PRESS TO EXIT
12. 2 KEYPAD LOCKOUT & ALARM OUTPUTS - SETTING
12. 3 LIGHT & SOUND (LED) - SETTING
KEYPAD BACKLIGHT SETTINGS
TO DISABLE
ALARM OUTPUT ENABLE
TO EXIT PROGRAMMING
PRESS TO EXIT
TO ENABLE
TO EXIT PROGRAMMING
PRESS TO EXIT
12. 4 LED'S - SETTING
LED SETTINGS
DISABLE RED LED
ENABLE RED LED (DEFAULT)
6
0
#
6
1
#
7
0
#
7
1
#
Keypad Lockout & Alarm Output options.
If there are 10 invalid cards or 10 incorrect PIN numbers in a 10 minute period either the keypad will lockout for 10 minutes or the alarm
will operate for 0~3 minutes, depending on the option selected below.
7
2
#
*
*
8 1 0 #
8
1
1
#
*
8
2
0
#
8
2
1
#

12. 5 KEYPAD TONE - SETTING
TO EXIT PROGRAMMING
PRESS TO EXIT
KEYPAD TONE SETTING
DISABLE TONE
ENABLE TONE (DEFAULT)
TO EXIT PROGRAMMING
PRESS TO EXIT
12. 6 CONVERTING RELAY 2 TO DOORBELL - SETTING
NORMAL SETTING (RELAY 2 NORMAL USE)
DEFAULT
DOORBELL ENABLE
TO EXIT PROGRAMMING
PRESS TO EXIT
12. 7 ALARM OUTPUT TIME - SETTING
SETTING ALARM OUTPUT TIME (0 ~ 3 )MINS
DEFAULT IS 1 MINUTE
TO RE-SET DOOR OPEN TOO LONG ALARM
CLOSE THE DOOR OR
TO EXIT PROGRAMMING
PRESS TO EXIT
TO RE-SET THE ALARM
TO RE-SET DOOR FORCED OPEN ALARM
OR
OR
*
Keypad Tone:
The keypad tone can be set On or Off.
When on, the device will BEEP when a Key is pressed and when off, the device will be silent.
8
3
0
#
8
3
1
#
*
Converting Zone 2 to Door Bell
(When there is no need to operate a second door, Zone 2 can be set to operate a Doorbell.
The Doorbell wires are connected to COM2 and NO2.
Press #, the keypad will send the signal to the doorbell.
8
4
0
#
8
4
1
#
*
5
0~3 MINS
#
*
READ A VALID CARD
#
MASTER CODE
READ A VALID CARD
#
MASTER CODE

TO ADD A DURESS PIN USER
14.0 WIEGAND MODE - SETTING
13.0 DURESS - SETTING (AGAIN MUST BE IN PROGRAMMING MODE)
ID NUMBER IS ANY NUMBER BETWEEN (2101~2110)
TO ADD A DURESS CARD USER
ID NUMBER IS ANY NUMBER BETWEEN (2101~2110)
TO DELETE A DURESS PIN/CARD USER
TO EXIT PROGRAMMING
PRESS TO EXIT
TO DELETE ALL USERS (USE WITH CAUTION)
TO ADD A DURESS PIN USER
FACTORY DEFAULT IS WIEGAND 26 BIT
UKP-EM Supports Wiegand 26 ~ 37 Bit Input and Output.
The Unit May Be Used As just as an Output reader or a Controller.
There are 10 groups for Duress PIN / card available.
When inputing Duress PIN/card, the door will open and at the same time, the output alarm will operate.
Note:
①User ID number must be any 4 digits between 2101 ~ 2110
②Duress PIN/card must be unique and should be distinguished from the common PIN/card.
(If the Duress PIN/card is the same as a common PIN/card, it will become invalid in Duress, and operate as a common user function instead)
1 #3 USER ID NO. PIN #
1 #
*
3 USER ID NO. CARD #
2 #0 USER ID NO.
2 #3 0 0 0 0
1 #
26 ~ 37

15.1 OPERATING AS A WIEGAND OUTPUT READER
In This Mode, The UKP-EM Supports Wiegand 26 ~ 37 Bit Output.
Therefore, D1 & D0 Wiegand Data Lines Can be Connected to Any Control Panel That Supports Wiegand 26 or 37.
TRANSMISSION FORMATS
IT'S IMPORTANT THAT IN THIS CASE THE KEYPAD SHARES THE 3RD PARTY CONTROLLER'S PSU GROUND
WIEGAND WILL NOT FUNCTION IF YOU DO NOT HAVE A COMMON GND BETWEEN KEYPAD AND CONTROLLER
15.0 INTERCONNECTING TWO DEVICES
◆1: Keypad Transmission
The Reader will transmit the PIN data when it receives the last key (#) press after PIN code.
Format: PIN Code (any 4~8 digits between 0000 ~ 99999999)
Example: PIN code: 111111
Press 111111 #, then the output format will be: 0000111111
(Note: If an invalid PIN (any 4~8 digits) is entered, the data is still transmitted.)
◆2: Proximity Card Transmission
The Reader will transmit the card data when it reads the Card.
Format: Card Number
(Note: It doesn't matter if the card is valid or invalid, the data is still transmitted)

15.2 UKP-EM OPERATING AS A CONTROLLER
In this mode the UKP-EM supports a Wiegand 26~37 bit input so an external Wiegand device with a 26~37 bit output can be connected
to the Wiegand input terminals on the UKP-EM.
Either an ID card reader (125 KHz) or an IC card reader (13.56MHz) can be connected to the UKP-EM.
Cards are required to be added at the external reader, except where an external ID reader is used, in ths case, cards can be added at
either reader or controller. See figure.

Sales [phone]
Enquiries [email protected]o.uk
Website www.genieproducts.co.uk