Genie HDUBARTK-T User manual

HDUBARTK-T User Manual
HDUBARTK-T
1 Channel HD Analog Video UTP
Transmitter/Reciever
User Manual

HDUBARTK-T User Manual HDUBARTK-T User Manual
1 Channel HD Analog Video UTP
Transmitter/Reciever
User Manual
The 1ch HD analog video UTP transceiver transfers real-time analog video signal up to 1200m through
Cat5/5e/6 cable. It is compatible with analog video signals of CVBS, HDCVI, HDTVI, and AHD. The
transceiver consists of SV unit connecting with DVRs and RM unit with cameras. It features protections
of surge immunity and ESD
immunity. The transceiver with small volume and joinable design ts easily in many locations. (e.g., villa,
super market, oce, hotel).
HD

Analog

Camera
LCD
DVR
10A
250V
LN
CCC
ACIN
Power&HD
Video
UTP
Receiver
Power&H D
Video
UTP
Transm itter
Application
Features
• Power supply:12~20V DC / 9~24V AC
• Transmission signal: HDCVI, HDTVI, AHD, CVBS signals 4in1 full compatible design;
• Transmission distance: 0~1200m( work with active receiver/transmitter);
• Major function: Adopt twisted-pair to transit video, switch adjust transmission distance;
• Safety Performance: Power high anti-interference, superior surge immunity, ESD protection and
anti-interference ability, wide-voltage DC/AC input;
• Mechanics: Combined connection available, optional MIT rack, which satisfy multi channels
• centralized application. Transfer video signal in real-time via twisted-pair, active video transmission
solution, max.1200m transmission distance.
Notice
1. Standard Cat5e/6 cable and 75 4 or above coax are strongly suggested for reaching the maximum
transmission distance!
2. Please use standard UTP cable and coax to ensure the stable transmission.

HDUBARTK-T User Manual
Powe rInpu t
Video +
Video -
Groundin g
VideoOutput
Switc h
Vide oLED
Powe rLED
Powe rInpu t
Video +
Video -
Groundin g
Vide oInpu t
Switch
Vide oLED
Powe rLED
Right  View
LeftView TopView
TopView Right 
View
LeftView
RM Un it
SV  Unit
Panel Diagram
Installation Steps
Please check the following items before installation, if it is missing, please contact the dealer.
• RM Unit 1pc
• SV Unit 1pc
• User Manual 1pc
Please follow installation steps as below:
1. Turn o the power of all the related devices before the installation; otherwise the device would be
damaged;
2. Check if the any cable has been occupied by other device;
3. Connect corresponding ports of cameras and other related devices with Video BNC port of TX
unit;
4. Connect the grounding terminal of TX unit by bare grounding wire and a pair Ethernet cable;
5. Connect the grounding terminal of RX unit by bare grounding wire and a pair Ethernet cable;
6. Connect display device and BNC port of RX unit by coaxial cable;
7. Connect power ports of RX and TX units by power cable;
8. Check the installation and connection of equipments are correct and the equipments are working
properly, then power on system;
9. Make sure image displays and other devices are working.
Installation Methods
Indoor Wall-mounting

HDUBARTK-T User Manual HDUBARTK-T User Manual
Specication
Model Number HDUBARTK-R HDUBARTK-T
Transfer Signal Number 1 Ch Video
Transmission Distance 1,200m
Voltage Input DC12-20V or AC9-24V
Video Connector 1xBNC (Male)
Cable Pod 1*3 Pin Terminal
Compatible Video Type HDCVI, HDTVI, AHD, CVBS Signal
Transfer Bandwidth 0-75MHz
Signal Indicator Yellow Solid ON : Power Input Normal
Anti-Interference Green Solid ON : Signal Input Normal
Surge Protection Coaxail Port >60dB
Surge Proctection of Line
Connector
2KV Dierential-mode
2KV Common-mode
Per : IEC61000-4-2
ESD Protection 1a Contact Discharge 6KV
1b Air Discharge 8KV
Per : IEC61000-4-2
Operation Temperature -10°C - 55°C
(0-95% Humidty)
Storage Temperature -45°C - 75°C
(0-95% Humidty)
Weight 65g
Dimesnions (W x L x H) 45 x 113 x 29 (mm)
Genie CCTV reserves the right to change specications without notice. Please contact your representative to
conrm current specications.

HDUBARTK-T User Manual
Transmission Distance Table ( Recommended)
Signal Type HDCVI
720P
HDCV I
1080P
AHD
720P/960P
AHD
1080P
HDTVI
720P
HDTVI
1080P
Transmission 
Distanc e 600m 500m 700m 300m 400m 400m
Adjustment Diagram
The transmission distances of dierent signals correspond to dierent switch settings as below:
HDCVI720P 0-150m 150-500m 500-600m
Switch Setting
RM Unit SV Unit RM Uni t SV Uni SV Unit
HDCVI080P 0-150m 150-200m 200-300m 300-500m
Switch Setting
RM Uni t SV Unit SV Unit RM Unit SV Unit RM Unit SV Unit
AHD720P 960P 0-300m 300-400 00-600m 600-700m
Switch Setting
RM Unit SV Unit RM Unit SV Unit RM Unit SV Unit RM Uni t SV Unit
AHD1080P 0-200m 200-300m
Switch Setting
RM Unit SV Unit RM Uni t SV Unit
HDTVI720P 0-50m 50-200m 200-300m 300-400m
Switch Setting
RM Unit SV Unit RM Unit SV Unit RM Unit SV Unit RM Unit SV Unit
0-200m 200-300m 300-400m
Switc hSetting
RMUnitSV Unit SV Unit RM Unit SV Unit
t
m 4
Unit RM
RM Unit
RM
U
nit
Notice
1. Please follow the steps for troubleshooting if power cuts or image displays abnormally under the
longest transmission distance:
a. Restore switch of SV unit on 5X mark;
b. Reboot;
c. Adjust the switch when DVR works smoothly.
2.There are 2 marks of 10X on RM unit. Right mark features high denition and saturation.

HDUBARTK-T User Manual HDUBARTK-T User Manual
GENIE CCTV LTD.
CCTV House, City Park, Watchmead,
Welwyn Garden City, Hertfordshire, AL7 ILT
Tel: [phone] Fax: [phone]
www.geniecctv.com