GeoVision GV-SD220 Series Operator's manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use. ISD220200-QG-B
Quick Start Guide
GV-IP Speed Dome

© 2013 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in
part, without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any
kind and assumes no responsibility for errors or omissions. No liability is
assumed for incidental or consequential damages arising from the use of
the information or products contained herein. Features and specifications
are subject to change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows and Windows
XP are registered trademarks of Microsoft Corporation.
June 2013

Contents
1. Introduction............................................................... 1
2.......................... 2
2
................................ 2
................................ 3
4
................................ 5
ount........... 5
Mount..................... 7
................................ 9
10
.............................. 10
ng In..................11
.............................. 13
.............................. 15
2.8 Configuring a Preset Position............................................... 17
2.9 Configuring a Sequence Route ............................................ 19
2.10 Configuring a Cruise .......................................................... 22
2.11 Configuring an Auto Pan..................................................... 23
2.12 Configuring a Tour.............................................................. 25
2.13 Upgrading System Firmware.............................................. 27
2.14 Restoring to Default Settings.............................................. 29
. GV-SD220 / SD220-S.......................
2.1 Packing List ...........................................................................
2.1.1 Indoor GV-IP Speed Dome...........
2.1.2 Outdoor GV-IP Speed Dome ........
2.2 Overview................................................................................
2.3 Installation..............................................
2.3.1 Indoor GV-IP Speed Dome: Hard-Ceiling M
2.3.2 Outdoor GV-IP Speed Dome: Wall
2.4 Connecting the Cables...........................
2.5 Accessing the Camera .........................................................
2.5.1 System Requirements ..................
2.5.2 Looking Up the IP Address and Loggi
2.6 The Web Interface..................................
2.7 The PTZ Control Panel...........................
i

2.14.1 Restoring All the Settings.......................................... 29
29
ings Only............... 30
3. G 31
.............................. 31
.............................. 31
.............................. 32
.............................. 33
3.3 Installation............................................................................ 34
e Mount ................ 34
Pendent Mount..... 37
.............................. 39
.............................. 41
41
gging in.................. 42
3.6 The Web Interface................................................................ 44
3.7 The PTZ Control Panel......................................................... 45
3.8 Configuring a Preset Position............................................... 47
3.9 Configuring a Sequence Route ............................................ 49
3.10 Configuring a Cruise .......................................................... 52
3.11 Configuring an Auto Pan..................................................... 54
3.12 Configuring a Tour.............................................................. 56
2.14.2 Restoring System Settings Only ...............................
2.14.3 Restoring PTZ Configuration Sett
V-SD200 / SD200-S...............................................
3.1 Packing List ...........................................
3.1.1 Indoor GV-IP Speed Dome...........
3.1.2 Outdoor GV-IP Speed Dome ........
3.2 Overview................................................
3.3.1 Indoor Speed Dome Mount: Surfac
3.3.2 Outdoor Speed Dome Mount: Mini
3.4 Connecting the Cables...........................
3.5 Accessing the Camera ...........................
3.5.1 System Requirements ................................................
3.5.2 Looking up the IP Address and Lo
ii

3.13 Upgrading System Firmware.............................................. 59
3.14 Restoring to Default Settings.............................................. 61
iii

iv

1. Intr
de. In the following
sections, you will be guided through the basic installations and
io V D200/GV-SD200-S.
led tion, er’s Manual on the
re C
oduction
Welcome to the GV-IP Speed Dome Quick Start Gui
configurat ns of the G -SD220/GV-SD220-S/GV-S
see GV-IP Speed Dome UsFor detai informa
Softwa D.
Model Application Description
GV-SD220 Indoor
GV-SD220-S Outdoor
2 MP H.264, 20x optical zoom, 12x
digital zoom, WDR pro
GV-SD200 Indoor
GV-SD200-S Outdoor
2 MP H.264, 18x optical zoom, 8x
digital zoom, WDR pro

2. GV-SD220 / SD220-S
2.1 Packing List
2.1.1 Indoor GV-IP Speed Dome
•Indoor GV-IP Speed Dome •Hard-Ceiling Cover
te•Mounting Pla
•GV-IP Speed Dome
Software CD
•GV-NVR Software DVD

GV-SD220 / SD220-S
2
2.1.2 Outdoor GV-IP
•Outdoor GV-IP Speed Dome
Speed Dome
•Pendant Tube
•Hex Keys x 2 •M6 Screws x 3
•Desiccant pack x 4 •GV-IP Speed Dome
Software CD
•GV-NVR Software DVD
3

2.2 Overview
1
2
3
4
5
6
No. Name Description
1. e factory default values.
storing to Default Settings.
ault Restores all the settings to th Def For details, see 2.13 Re
2. Status status LED turns green when the power is on and
fades when the camera is ready for use.
The
3. Power The power LED turns green when the power is on.
4. ACT The ACT LED flashes orange light upon data
transmission.
5. Link The Link LED turns green with Internet connectivity.
6. Memory
Card Slot
Insert a micro SD/SDHC/SDXC card to store
recording data.
4

GV-SD220 / SD220-S
2
2.3 Installation
There are multiple ways to install the GV-IP Speed Dome. Only the
standard installation methods are introduced in the Quick Start Guide. For
GV-SD220/220-S IP
Speed Dome, Chapter 5, GV-Mount Installation Guide on the Software CD.
2.3.1 Indoor GV-I eiling Mount
details on optional installations, see Installing the
P Speed Dome: Hard-C
Required Items
•Indoor packing (supplied)
•ceiling screws x 3 (user-prepared)
1. Secure the mounting plate to the ceiling with self-prepared screws.
5

2. Secure the indoor GV-IP Speed Dome to the mounting plate.
A. Loosen the screw on the mounting plate
B. Align the camera to the mounting plate and rotate the camera
body to the right.
C. Tighten the screw.
3. Put on the hard-ceiling cover.
Note: Cut away a side of the cover if you want to run the cable through.
6

GV-SD220 / SD220-S
2
2.3.2 Outdoor : Wall Mount GV-IP Speed Dome
Required Items
•Outdoor packing (supplied)
•ceiling screws x 4
(user-prepared)
1. Insert the desiccants to the camera.
Note: Be sure to conceal the desiccants in the GV-IP Speed Dome within
2 minutes of opening the desiccant pack.
A. Remove the camera cover using the supplied hex key.
7

B. Unpack two desiccants and insert them to the indicated places.
C. Follow step 1A to secure the camera cover with the supplied
hex key.
2. Thread the camera cable through the pendant tube and lock the
camera to the pendant tube.
3. Secure the camera to the pendant tube with the supplied M6 screws.
4. Secure the pendant tube to the wall with self-prepared screws.
8

GV-SD220 / SD220-S
2
2.4 Connecting the Cables
With the Data Cable, you can connect the power, microphone, speaker, and
I/O devices to the GV-IP Speed Dome. The Data Cable is illustrated as
below.
I/O Wires
Microphone
Speaker
Power Adapter
Ethernet
No. re DefinitionWi
1Orange Alarm In 1
2Yellow Alarm In 2
3Green Alarm In 3
4Blue Alarm In 4
5Pink Ground
6Purple Alarm Out
7White Alarm Out Open
8Gray Alarm Out Close
9

2.5 Accessing the Camera
functions through Web browser, ensure your
work connection and use one of the following web
•Microsoft Internet Explorer 7.x or later
Google Chrome
2.5.1 System Requirements
To access GV-IP Speed Dome
PC is in good net
browsers:
•
•Mozilla Firefox
•Safari
Note:
1. al settings are required.For users of Internet Explorer 8, addition
For details, see Appendix C.For more details, see 1.2 System
Requirements, GV-IP Speed Dome GV-SD220 User’s Manual on
the Software CD.
2. With non-IE browsers,
A. Motion Detection, Text Overlay, two-way audio and GPS
map settings are not supported.
B. The Play function is only available on the live view window.
C. RTSP streaming must be kept as enabled.
10

GV-SD220 / SD220-S
2
2.5.2 Looking Up the IP Address and L
By default, the IP address of your GV-IP Speed Do
ogging In
me is assigned by the
DHCP server unless your router does not support DHCP. In this case, the
dhe steps below to look up
the dynamic IP address.
1. Install the GV-IP Device Utility program from the Software CD.
efault IP address will be 192.168.0.10. Follow t
Note: The PC installed with GV-IP Device Utility must be under the same
LAN with the camera you wish to configure.
2. On the PC desktop, select Start, select Programs and select GV IP
Device Utility to execute the program. The GV IP Device Utility
window appears and automatically searches for the GV IP devices
on the same LAN.
3. Click the Name or Mac Address o n sort.c lum to
4. Find the Mac Address of the camera to see its IP address.
11

12
5. To login, type the IP address in the browser. The login page appears.
6. Type the default ID and password admin and c
7. When accessing the GV-IP Speed Dome for t
set your browser to allow a one-time install
ActiveX
lick Apply to log in.
he first time, you must
ation of GeoVision
component onto your computer.
Note: If your router does not support DHCP, the default IP address will
be 192.168.0.10. In this case, it is strongly suggested to modify the IP
address to avoid IP address conflict with other GeoVision IP device on
the same LAN. For details, see Changing the IP Address in 2.1 Looking
Up the IP Address, GV-IP Speed Dome GV-SD220 User’s Manual on
the Software CD.

GV-SD220 / SD220-S
2
2.6 The Web Interface
12
123
11
45 6 78
10
9
No. Name Description
1 Play Plays live video.
2 Stop Stops playing video.
3 Microphone Talks to the surveillance area from the local
computer.
4 Speaker Listens to the audio around the camera.
13

No. Name Description
5 Snapshot Takes a snapshot of live video.
6 File S cal computer.ave Records live video to the lo
7 Full S
ew. Right-click the image
shot, Full Screen,
Resolution,Wide Angle Lens Dewarping, PIP,
s.
creen
Switches to full screen vi
to have these options: Snap
PAP, GPS and Google Map
8 Visual PTZ
tch to one of the three visual PTZ
control modes: Fixed Direction Move, Random
Clicks to swi
Move or Center Move.
9 PTZ to the home position.Home Click to return the dome view
10 I/O Control Starts the I/O Control Panel.
11 PTZ Control Starts the PTZ Control Panel and the Visual PTZ.
12
Show
System
Menu
Brings up these functions: Alarm Notify,Video
and Audio Configuration, Remote Config, Show
Camera Name and Image Enhance.
For detail, see 3.1 The Live View Window, GV-IP Speed Dome GV-SD220
User’s Manual on the Software CD.
14