GeoVision GV-VR360 User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use. VR360V10-QG-A
Quick Start Guide
GV-VR360 IR Virtual Reality IP Camera

© 2018 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note: No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
May, 2018

i
Contents
Note for Connecting to GV-VMS................................................. ii
Note for Installing Camera Outdoor .......................................... iii
1. Introduction........................................................................... 1
1.1 Packing List ............................................................................................. 1
1.2 Optional Accessories................................................................................ 2
1.3 System Requirements.............................................................................. 3
1.4 Software Supported ................................................................................. 3
1.5 Overview.................................................................................................. 4
2. Installation............................................................................. 5
3. Accessing the Camera ......................................................... 7
3.1 Looking Up the Dynamic IP Address ........................................................ 7
4. Setting up YouTube Live Streaming .................................... 9
4.1 Getting YouTube Live Stream................................................................... 9
4.2 Configuring Live Stream Settings ........................................................... 12
4.3 Starting Live Stream............................................................................... 13
5. Smart Device Connection .................................................. 14
6. Upgrading System Firmware ............................................. 15
7. Restoring to Factory Default.............................................. 16
7.1 Using the Web Interface......................................................................... 16
7.2 Directly on the Camera .......................................................................... 17

ii
Note for Connecting to GV-VMS
The camera is designed to work with and record on GV-VMS, a video management
system.
Once the camera is connected to the GV-VMS, the resolution set on the GV-VMS will
override the resolution set on the camera’s Web interface. You can only change the
resolution settings through the Web interface when the connection to the GV-VMS is
interrupted.

iii
Note for Installing Camera Outdoor
When installing the camera, be sure that:
1. The camera is set up above the junction box to prevent water from entering the
camera along the cables.
2. Any PoE, power, audio and I/O cables are waterproofed using waterproof silicon
rubber or the like.
3. The screws are tightened and the cover is in place after opening the camera
cover.

1
1. Introduction
Welcome to the GV-VR360 IR Virtual Reality IP Camera Quick Start Guide. In the
following sections, you will learn the basic installations and configurations. For a
detailed user manual, see the GV-VR360 IR Virtual Reality IP Camera User’s Manual:
http://www.geovision.com.tw/download/product/.
1.1 Packing List
IR Virtual Reality IP Camera
Mount Kit
Screw x 3
Screw Anchor x 3
Warranty Card
Torx Wrench
Hex Key
Silica Gel Bag
Download Guide

2
1.2 Optional Accessories
Optional devices can expand your camera’s capabilities and versatility. Contact our
sales representatives for more information.
Device Description
GV-PoE Switch
GV-PoE Switch is designed to provide power along with
network connection for IP devices. GV-PoE Switch is
available in various models with different numbers and
types of ports.
GV-Relay V2
GV-Relay V2 is designed to expand the voltage load of
GV-IP devices. It provides 4 relay outputs, and each can
be set as normally open (NO) or normally closed (NC)
independently as per your requirement.
Power Adapter Contact our sales representatives for the countries and
areas supported.

Introduction
3
1
1.3 System Requirements
CPU Intel® 6th generation CoreTM i3
Memory 4 GB or above
On Board Graphics Intel® HD Graphics 500 series or above
OS Windows 7 Service Pack 1 / Windows 10 or above
Web Browser Internet Explorer 10 / 11 or above
1.4 Software Supported
GV-VMS V18.1
GV-Control Center V3.6.0.0
GV-Edge Recording
Manager (for Windows) V.1.4.0.0
GV-Recording Server V1.4.0.0 + Patch for live stream only
GV-Eye V2.5.2 for IOS and V2.5.1 for Android

4
1.5 Overview
No. Description No. Description
1 Built-in microphone 7 Earth ground (M3 terminal)
2 IR LED 8 RJ45 waterproof
3 Fisheye lens 9 DC 12V jack (black)
4 Socket set screw 10 Digital input (white cable)
5 Audio in (pink jack) 11 Digital output (green cable)
6 Audio out (green jack, currently not
functional) 12 Ground wire (black cable)

5
2. Installation
The camera is designed for outdoors. With the standard package, you can install the
camera on the ceiling.
1. Adjoin the base with the straight tube by turning it clockwise.
2. Thread the cables of the camera to the base end through the opposite end of the
straight tube and rotate the straight tube clockwise to attach it to the camera.
3. Mount the camera onto the ceiling using the mounting kit and the supplied
screws and screw anchors.