GeoVision GV-APOE0811 User manual

March 8, 2021
1
GV-APOE0811 8-Port Gigabit 802.3at Web Management
PoE Switch
Packing List
1. GV-APOE0811 x 1
2. Power Cord x 1
3. Screw x 8
4. Rack Mount Kit
5. Rubber Feet x 4
6. GV-TA (1000Base-T Copper RJ-45 SFP
Transceiver) x 1
Front Panel
Note: If any of these items is found missing or damaged, please contact your local supplier
for replacement.
LED
Display
Gigabit
RJ-45
Gigabit
SFP
Reset
Button
Not
Functional

March 8, 2021
2
LED Indicators on the switch
LED Color/Status Description
PW Green System powered on.
SYS Blinking Green System is working.
Red Network through the corresponding port has been
successfully established at 10/100 Mbps.
Green Network through the corresponding port has been
successfully established at 1000 Mbps.
Link/Act
Blinking Red / Green Data currently being sent through the corresponding port
at 10/100 (orange) or 1000 (green) Mbps.
PoE Orange At least one device successfully powered through PoE.
Rear Panel

March 8, 2021
3
Mount Installation
Desktop
Rack

March 8, 2021
4
Connecting to GV-IP Cameras / Systems / Switches
GV-APOE0811 can be connected to up to 8 GV-IP Cameras and 2 GV-NVR / DVR / VMS
Systems or switches. You can also extend the connections by connecting to other switches.
Note:
1. The maximum cable length for:
• Gigabit RJ-45 (Cat5) is 100 m (330 ft).
• Gigabit RJ-45 (Cat5e or higher) can achieve 250 m (820 ft) by selecting Auto-10M or
10M for speed on the device’s Web interface. See details in Figure 16, 2.3.1 Port
Setting,GV-PoE Switch User’s Manual.
2. For connection that exceeds 250 m (820 ft), you can use the Gigabit SFP ports.
3. The supplied GV-TA (1000Base-T Copper RJ-45 SFP Transceiver) only supports
Gigabit Ethernet over Cat5e / Cat6 cable.
4. The port inserted with the GV-TA will not function if connected to a network speed of 10
Mbps or 100 Mbps.

March 8, 2021
5
Accessing Web Interface
Users can log in the Web interface to manage and set up the switch. Follow the below steps
to log in the Web interface.
1. To access the Web user interface, type the default IP 192.168.0.250 into your Web
browser. The login page appears.
2. Type the default username admin and password admin.Click Login In.
3. When prompted to create your login credentials, type the necessary information and click
Apply. The System Information window appears.
4. To configure the GV-PoE Switch, select desired functions from the left menu.
Loading Default Setting
You can load the default value with the Reset button or with the Web interface.
Hardware
1. Turn on the switch.
2. Press and hold the Reset button on the front panel of the switch for 5 seconds until all
the LED start blinking.
3. Release the button. The switch is restored to its default settings.

March 8, 2021
6
Web Interface
1. Management > Configuration > Save Configuration.
2. Click Restore Factory Default to restore the switch to the original configuration.
Note: After loading default by pressing the Reset button or from the Web interface, you will
need to configure IP address and Password again.
Updating Firmware
1. Management > Firmware > Upgrade/Backup.
2. Select Upgrade in the Action section.
3. Select TFTP or HTTP in the Method section.
If TFTP is selected, select Hostname / IPv4 / IPv6 in the Address Type section >
specify the TFTP server address.
If HTTP is selected, click Browse to select the firmware file.
4. Click Apply. The upgrade process is started.
5. After the firmware is successfully upgraded, click Logout from the left menu and re-login
the switch.
Specifications
For detailed specifications, see Datasheet.