GeoVision GV-APOE4813 User manual

May 5, 2023
1
GV-APOE4813
48-Port Gigabit Web Management PoE Switch
Packing List
1. GV-APOE4813
2. Power Cord
3. Screw x 8
4. Rack Mount Kit
5. Rubber Feet x 4
Note: If any of these items is found missing or damaged, please contact your local
supplier for replacement.

May 5, 2023
2
Front Panel
Gigabit RJ-45 Ports SFP+ Uplink Ports
Reset Button
Console Port
IMPORTANT:The Console port is used to connect to the serial port of a computer or other
terminal device for debugging only.
LED Indicator
LED
Color/Status
Description
PWR
Off
No power supply
Green
System powered on
DATA
Off
No devices connected to the corresponding port
Green On
Network successfully established at
10/100/1000Mbps through the corresponding port
Blinking Green
Data actively being sent or received by the Switch
over the corresponding port
PoE
Off
No PoE powered device (PD) connected
Orange On
PoE powered devices connected with successful
power supply
Blinking Orange
Abnormal PoE supply of the corresponding port

May 5, 2023
3
SYS
Blinking Green
System working properly
Off
System being restarted or system abnormal
Rear Panel

May 5, 2023
4
Mount Installation
Leveled Installation
Rackmount Installation

May 5, 2023
5
Connecting to GV-IP Camera
The switch can be connected to up to 48 GV-IP Cameras and 1 GV-NVR / DVR / VMS
System. You can also extend the connection by connecting to another switch.
GV-NVR / DVR / VMS System
GV-IP Camera x 48
Switch
Note:
1. GV-NVR / DVR / VMS or a switch can connect to the RJ-45 ports or SFP+ ports.
2. The maximum cable length for:
•Gigabit RJ-45 (Cat.5) is 100 m (330 ft).
•Gigabit RJ-45 (Cat.5e, 6) can achieve 250 m (820 ft) by setting the network
bandwidth of the 48 PoE ports to 10 Mbps per port on the switch’s Web interface.
See details in 3.1.2 Bandwidth control configuration, GV-APOE4813 User’s Manual.
3. For connection that exceeds 250 m (820 ft), use the 10 Gigabit SFP+ ports.

May 5, 2023
6
Accessing the Web Interface
Users can log in the Web interface to manage and set up the switch.
1. To access the Web user interface, type the default IP 192.168.0.250 into your Web
browser. The login page appears.
2. Type the default username admin and password admin. Click Login In.
3. When prompted to create your login credentials, type the necessary information and click
Apply. The System Information page appears.
Loading Default Setting
If for any reason the device is not responding properly, you can reset it to its factory default
settings either directly on the device or through its Web interface.
Hardware
1. Turn on the switch.
2. Press and hold the Reset button on the front panel of the switch for 5 seconds until all
the LED start blinking.
3. Release the button. The switch is restored to its default settings.

May 5, 2023
7
Web Interface
1. Switch basic configuration > Switch basic configuration > Save current running-
configuration.
2. In the Reboot with the default configuration table, click Apply to restore the switch to
the original configuration.
Note: After loading default by pressing the Reset button or from the Web interface, you will
need to configure IP address and Password again.
Updating Firmware
1. Switch basic configuration > Firmware update.
2. Select TFTP service or HTTP Upgrade page.
⚫Select TFTP service > TFTP client service, specify the TFTP server address, local
file name, server file name, and select the operation type and transmission type.
⚫Select FTP service > FTP client service, specify the FTP server address, FTP server
user name, password, local file name, server file name, and select operation type and
transmission type.
⚫If HTTP Upgrade is selected, click Select File to select the firmware file.
3. Click Apply. The upgrade process is started.
4. After the firmware is successfully upgraded, the system will automatically log out and
reboot.
Specifications
For detailed specifications, see Datasheet.