GeoVision GV-POE2411 User manual

Multicam Digital
GV-POE2411 User's Manual
GV-PoE Switch
POE2411-B
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.

© 2016 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part, without
the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is accurate.
GeoVision, Inc. makes no expressed or implied warranty of any kind and assumes no
responsibility for errors or omissions. No liability is assumed for incidental or
consequential damages arising from the use of the information or products contained
herein. Features and specifications are subject to change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV series
products are trademarks of GeoVision, Inc. Windows and Windows XP are registered
trademarks of Microsoft Corporation.
July 2016


Contents
1. Safety Precautions........................................................................................... 1
2. Introduction....................................................................................................... 2
2.1 Product Overview ............................................................................................... 2
2.2 Key Features....................................................................................................... 2
2.3 Package Contents............................................................................................... 4
3. Hardware Description ...................................................................................... 5
4. Preparation for Web Configuration................................................................. 8
5. User Login....................................................................................................... 10
6. Configuration...................................................................................................11
6.1 System................................................................................................................11
6.2 Ports ...................................................................................................................13
6.3 VLANs.................................................................................................................15
6.4 Aggregation........................................................................................................16
6.5 LACP...................................................................................................................17
6.6 RSTP...................................................................................................................18
6.7 IGMP Snooping..................................................................................................20
6.8 Mirroring.............................................................................................................21
6.9 Quality of Service ..............................................................................................22
6.10 Filter..................................................................................................................24
6.11 Power over Ethernet........................................................................................25
6.12 Rate Limit .........................................................................................................26
6.13 Storm Control...................................................................................................27
7. Monitoring....................................................................................................... 28
7.1 Statistics Overview............................................................................................28
7.2 Detailed Statistics..............................................................................................28
7.3 LACP Status.......................................................................................................29
7.4 RSTP Status .......................................................................................................31
7.5 IGMP Status........................................................................................................33
7.6 VeriPHY...............................................................................................................34
7.7 Ping.....................................................................................................................35
8. Maintenance.................................................................................................... 36
8.1 Warm Restart......................................................................................................36
8.2 Factory Default...................................................................................................36
8.3 Software Upload.................................................................................................37
8.4 Configuration File Transfer...............................................................................37
9. Logout ............................................................................................................. 38
10. Restoring Default Settings............................................................................. 39
i





ii
11. Specifications................................................................................................. 40


1. Safety Precautions
FCC Warning
This Equipment has been tested and found to comply with the limits for a Class-A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance with the instructions.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the users are encouraged to try to correct the
interference by one or more of the following measures:
zReorient or relocate the receiving antenna.
zIncrease the separation between the equipment and receiver.
zConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
zConsult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio
interference in which case the users may be required to take adequate measures.
1




2. Introduction
2.1 Product Overview
The GV-POE2411 is a 24-port 10/100/1000BaseT(X) PoE+ with 4 Combo SFP Rack-mount
Web Smart PoE Switch. The switch supports IEEE 802.3at Power over Ethernet standard,
maximum 400 W power consumption, and no special network cable is required for connecting
your powered devices (PD), such as IP cameras. The switch also provides exceptionally
smart Web management features, such as VLAN, QoS, RSTP, IGMP Snooping, LACP, Port
Security, etc. The switch is designed for medium or large network environment to strengthen
its network connection and efficiency. It also gives you the option of installing it in a 19”
cabinet with a rack-mount kit or underneath a desk.
2.2 Key Features
Interface
zNumber of Ports: 24
24-port 10/100/1000BaseT(X) with RJ-45 Connectors, PoE+
4-port Gigabit SFP Combo Uplink Port
Performance
zMAC Address: 8 K
zBuffer Memory: 4 M bits
zJumbo Frames: 9.6 KB
zTransmission Method: Store and Forward Mechanism
Software Feature Description
zPort Management
Port Configuration: Enable / Disable such as Port State, Speed / Duplex, Flow
Control
Port Mirroring: One to one, one to many, many to one mirroring

2

Introduction

2
Bandwidth Control: Up to 256 levels Bandwidth Control for TX and RX Rate
Broadcast Storm Control: Broadcast Storm Control and Threshold Setting
PoE Control: PoE Enable / Disable, PoE Status
zVLAN Setting
VLAN Mode: Port-based and Tag-based VLAN
Port Based VLAN: 24 ports
Tag Based VLAN: Up to 16 VLANs, Available VID from 1~4094
zQoS Setting
Supports up to 4 queues
Class of Service schemes: 802.1p
DSCP
zSecurity Setting
Port Security - IEEE 802.1X
TCP / UDP Filtering: Source IP Filter
zSpanning Tree Protocol
Version: Support Legacy Spanning Tree Protocol & Rapid Spanning Tree Protocol
zIGMP Snooping V1&V2
zBasic Features
Embedded HTTP Web Management
User name / Password Authentication Configuration
Configuration Backup / Recovery
Secure Management
3





4
2.3 Package Contents
Before you start to install this switch, verify your package that contains the following items:
1. GV-POE2411 x 1
2. AC Power Cord x 1
3. Screw x 8
4. Rack Mount Kit x 1
5. User’s Manual CD x 1
6. GV-POE2411 Quick Start Guide x 1

Hardware Description

3
3. Hardware Description
This section gives a physical and functional overview on the 24-Port Gigabit Ethernet with
4-Port Combo Gigabit SFP Web Management Switch.
Product Overview
Front Ethernet Ports
The front panel of the Web smart switch consists of 24 10/100/1000BaseT(X) RJ-45 ports and
4 SFP Combo Uplink ports. The LED Indicators are also located on the front panel.
24 Port Gigabit with 4 SFP PoE+ Management Switch
Power Reset
6
F2
F3
F4
F1 F2 F3 F4
2 4
1 3
8
57 9111315
10 12 14 16
Combo
F1 1
LINK/ACT
PoE
LINK/ACT
PoE
3 5 7 9 11 13 15
161412108642 18
17
2420 2218
17 19 21 23
20 22 24
19 21 23

IMPORTANT: The 4 SFP ports labeled F1 ~ F4 are associated with the 4 RJ-45 ports labeled
1 ~ 4 respectively. When one of the two associated ports is used, the other port will not work.
For example, if the Gigabit SFP port labeled F1 is used, the Gigabit RJ-45 port labeled 1 will
not function.
5




LED Indicators
The LED Indicators present real-time information of systematic operation status. The following
table provides description of LED status and their meaning.
LED Color/Status Description No. of LED
Amber On Power on
Power Off Power off Power
Green On Link Up
Green Blinking Data activating
Link / ACT
Off No connection
Amber On Port is linked to Power Device
PoE Off No Power Device is connected
Port 1~24
(10/100M/1000M)
Green On Link Up
SFP Green Blinking Data activating Port F1~F4
Reset Button
The button allows you to restore the configuration to default. For details see 10. Restoring
Default Settings.
Rear Panel
The 3-pronged power plug is placed at the rear panel of the switch right side shown as below.

Hardware Installation
Set the switch on a large flat space with a power socket close by. The flat space should be
clean, smooth, level and sturdy. Make sure there is enough clearance around the switch to
allow attachment of cables, power cord and allow air circulation. The last, use twisted pair
cable to connect this switch to your PC and then users could start to operate the switch.
AC Power Input
Connect the attached power cord to the AC power input connector; the available AC power
input is range from 100-240 V/AC.
Ethernet Cable Request
The wiring cable types are as below.

6

Hardware Description

7
3
10BaseT: 2-pair UTP/STP Cat. 5 cable, EIA / TIA-568 100-ohm (Max. 100 m)
100BaseTX: 2-pair UTP/STP Cat. 5 cable, EIA / TIA-568 100-ohm (Max. 100 m)
1000BaseT: 4-pair UTP/STP Cat. 5e 6 cable, EIA / TIA-568 100-ohm (Max. 100 m)
PoE: To deliver power without problem, the Cat 5 / 5e and Cat 6 cable is suggested. The high
quality Ethernet cable reduces the lost while power transmission.
SFP Installation
While installing the SFP transceiver, make sure the SFP type of the 2 ends is the same and
the transmission distance, wavelength, fiber cable can meet your request. The way to connect
the SFP transceiver is to plug in SFP fiber transceiver first. The SFP transceiver has 2 plugs
for fiber cable, one is TX (transmit), the other is RX (receive). Cross-connect the transmit
channel at each end to the receive channel at the opposite end.
IMPORTANT: The maximum cable length for Gigabit RJ-45 is 100 meters. For connection
that exceeds 100 meters, you can use the Gigabit SFP ports.




4. Preparation for Web Configuration
The web management page allows you to use a standard web-browser such as Microsoft
Internet Explorer, Google Chrome or Mozilla Firefox, to configure and interrogate the switch
from anywhere on the network.
Before you attempt to use the web user interface to manage switch operation, verify that your
switch is properly installed on your network and that every PC on this network can access the
switch via the web browser.
Verify that your network interface card (NIC) is operational, and that your operating system
supports TCP/IP protocol.
Wire the switch power and connect your computer to the switch. The switch default IP address
is 192.168.0.250. The switch and the connected PC should locate within the same IP Subnet.
Change your computer's IP address to 192.168.0.xxx or other IP address which is located in
the 192.168.0.xxx (For example: IPAddress: 192.168.0.2; Subnet Mask: 255.255.255.0)
subnet.
Figure4-1

8

Preparation for Web Configuration

9
4
Launch the web browser and Login.
1. Launch the web browser (Internet Explorer or Mozilla Firefox) on the PC.
2. Type http://192.168.0.250 (or the IP address of the switch). And then press Enter.
3. The login screen will appear.
4. Type the default user name and password: admin.
If you can't login the switch, the following steps can help you to identify the problem.
1. Switch to DOS command mode and type the "ipconfig" to check the NIC's setting. Type
the "ping 192.168.0.250"to verify a normal response time.
2. Check the security or Firewall settings, high security level may limit the web access.
3. Try a different web browser, like the Mozilla or Google Chrome.




5. User Login
This part instructs users how to set up and manage the switch through the web user interface.
Follow the description to understand the procedure.
At first, open the web browser, type http://192.168.0.250 and then the users will see the login
page. Type the default password admin and click Apply to pass the authentication. Once you
are logged in, the main page will appear.
Login page
Figure 5-1
Main Page
Figure 5-2

10

Configuration

6

6. Configuration
6.1 System
Figure 6-1
The System Configuration page displays the following information:
MAC Address: Displays the unique hardware address assigned by manufacturer
(default).
S/W Version: Displays the switch’s firmware version.
H/W Version: Displays the switch’s Hardware version.
Active IP Address: The current active IP address of the switch.
Active Subnet mask: The current active subnet mask of the IP Address.
Active Gateway: The current active Gateway of the switch.
DHCP Server: The IP of the DHCP Server. Display after DHCP Client enabled.
11




Lease Time Left: The least received from the DHCP server. Display after the DHCP
Client enabled.
DHCP Enabled: Click the box to enable DHCP Client mode.
Fallback IP address: Manually assign the IP address that the network is using. The
default IP is 192.168.0.250
Fallback Subnet Mask: Assign the subnet mask to the IP address
Fallback Gateway: Assign the network gateway for industrial switch. The default
gateway is 192.168.0.254.
Management VLAN: ID of a configured VLAN (1-4094) through which you can manage
the switch. By default, all ports on the switch are members of VLAN 1. However, if the
management VLAN is changed, the management station must be attached to a port
belonging to this VLAN.
Name: Type in the new user name information.
Password: Type in the new password (The default value is admin).
Inactivity Timeout (secs): Specify the period for the system to time out and display the
login page when there is no activity.
Click Apply to configure the switch settings. Click Refresh to reset the details displayed.

Note: After changed to DHCP mode, the switch must be restarted to get a new IP address.
However, since the switch only provides Web management, it is hard for users to find its
new IP. Do not try this mode without pre-configured DHCP setting in DHCP Server.


12

Configuration

6

6.2 Ports
In Port Configuration, you can set and view the operation mode for each port.
Figure 6-2
Enable Jumbo Frames: This switch provides more efficient throughput for large
sequential data transfers by supporting jumbo frames on Gigabit Ethernet ports up to
9216 bytes. Compared to standard Ethernet frames that run only up to 1.5 KB, using
jumbo frames significantly reduces the per-packet overhead required to process protocol
encapsulation fields.
Power Saving Mode: Select Full, Link-up, Link-down or Disable to adjust the power
provided to ports based on the length of the cable used to connect to other devices. Only
sufficient power is used to maintain connection requirements.
Port Configuration
~Mode: Set the port speed as Auto, 10 half, 10 Full, 100 Half, 100 Full, 1000 Full or
Disabled.
13




~Flow Control: Enable the automatic management of transmission speed.
Drop frames after excessive collisions: Enable the switch to drop frames when
excessive collisions occur in half-duplex mode.

IMPORTANT: It is recommended when enabling the Jumbo Frame function, the network
card of the PC used for accessing the switch supports Gigabit Ethernet. Otherwise, the
presence of jumbo frames may slow down the speed of data transmission.


14

Configuration

6

6.3 VLANs
A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which
would allow you to isolate network traffic, so only the members of the same VLAN will receive
traffic from the ones of the same VLAN. Basically, creating a VLAN from a switch is logically
equivalent of reconnecting a group of network devices to another Layer 2 switch. However, all
the network devices are still plugged into the same switch physically.
Figure 6-3
[Add a VLAN]
VLAN ID: ID of configured VLAN (1-4094, no leading zeroes). Type the new ID and click
Add. The Web UI is directed to the VLAN Setup screen.

Figure 6-4
[VLAN Configuration List]
Lists all the current VLAN groups created for this system. Up to 16 VLAN groups can be
defined. VLAN 1 is the default untagged VLAN.
15




6.4 Aggregation
Port trunk allows multiple links to be bundled together and act as a single physical link for
increased throughput. It provides load balancing, and redundancy of links in a switched
inter-network. Actually, the link does not have an inherent total bandwidth equal to the sum of
its component physical links. Traffic in a trunk is distributed across an individual link within the
trunk in a deterministic method that called a hash algorithm. The hash algorithm automatically
applies load balancing to the ports in the trunk. A port failure within the trunk group causes the
network traffic to be directed to the remaining ports. Load balancing is maintained whenever a
link in a trunk is lost or returned to service.
To assign a port to a trunk, click the required trunk number and click Apply.
Figure 6-5

16