GFW CATANIA 4 DRAWER CHEST User manual

CATANIA 4 DRAWER CHEST
ASSEMBLY INSTRUCTIONS
Thank you for purchasing the CATANIA 4 DRAWER CHEST. Please read the instructions
carefully to ensure safe operation of the product.
Size: 770 x 395 x 890mm
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and ttings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking hazards.
Tools Required
V1 2022.07
Page 1of 16
3.5m/12'x 2
Person Required Approximate
Assembly Time
1 Hour

V1 2022.07
Page 2of 16
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
�Due to the size of this product we recommend that it is assembled in the room intended for use.
�When you are ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for
assembly.
�Unwrap all packaging materials and place the components on top of the carton box or on a clean floor to
prevent it from scratching.
�Check the pack and make sure you have all the parts listed.
�Ensure that this product is fully assembled as illustrated before use.
�Check all screws or bolts are tightened and inspect regularly
�This product should only be used on firm, level ground.
�Keep small parts out of reach of children.
�Make sure the legs remain in contact with the ground.
�Tools not included.
WARNINGS
�DO NOT use power tools to construct this product.
�DO NOT over tighten screws or bolts.
�DO NOT use this product if parts are missing, damaged or worn.
�DO NOT sit or stand on the product.
�It is essential that this unit is xed to the wall with the brackets provided for safety reasons. NB wall xings are
not included. Please source suitable fixings for your wall type. If in doubt please consult a qualified
tradesperson.
�WARNING : Always ensure the area to be drilled is free from hidden electrical wires, water or gas pipes.
CARE INFORMATION
�Never use scourers, abrasives or chemical cleaners.
�To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or detergents as they
can bleach or damage the product.

V1 2022.07
Page 3of 16
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer. The ttings pack contains small items that should be kept away from
small children.
CODE QTYPART NAME
A
B
C
1
D
E
Top Panel
Front Bar
Side Panel - L
Side Panel - R
Parts
CODE
F
15 x 380 x 870mm
DIMENSION
15 x 380 x 870mm
15 x 381 x 770mm
15 x 80 x 739mm
15 x 65 x 739mm
QTY DIMENSION
15 x 65 x 739mm
PART NAME
Front Bar 15 x 46 x 739mm
1
1
1
1
3
4
4
4
Drawer Front 15 x 190 x 770mm
4
L
Drawer Side - L 15 x 140 x 350mm
15 x 110 x 739mm
1
J
K
4
Drawer Side - R 15 x 140 x 350mm
G3
I
Bottom Support
Bottom Back Support
15 x 140 x 684mm
15 x 80 x 335mm
4
M
NDrawer Support
Drawer Bottom 3 x 344 x 693mm
Drawer Back
Centre Support
15 x 80 x 739mm
H1
Back Bar 3 x 383 x 790mm
2
Back Panel
BACK
PANEL
BACK
PANEL
DRAWER
BOTTOM

0 cm
1 cm
2 cm
3 cm
4 cm
Fixings (to scale)
0 cm
1 cm
2 cm
V1 2022.07
Page 4of 16
20x
M3.5 x 15mm
E
CSK Screw
30x
EU 24
B
Minix Bolt
71x
Dia. 8 x 30mm
C
Wooden Dowel
16x
M4 x 38mm
A
CSK Screw
16x
M6 x 8mm
F
Euro Screw
6x
H
Nail Leg
14x
G
Nail Pin
30x
Dia. 15 x 12mm
I
Minix Cam
1x
M4
N
Allen Key
4 set x
14" (350mm)
J
Drawer Slide
4 set x
14" (350mm)
K
Drawer Slide
Fixings (not to scale)
2x
D-16mm
L
Flat Washer
2x
1.2x15x32x75mm
M
L-Mounting
Bracket
2x
#10 x 16mm
D
Tapping Screw

V1 2022.07
Page 5of 16
Layout Parts on Soft Surface
BACK
PANEL
BACK
PANEL
x4
DRAWER
BOTTOM
x4
x4
x4
x4
x4