GFW OTTAWA NIGHTSTAND User manual

Page 1 of 6
Thank you for purchasing the OTTAWA NIGHTSTAND. Please read the
instructions carefully to ensure safe operation of the product.
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of
construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list.Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the
assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should
be kept away from young children whilst assembling your unit to avoid the danger of choking hazards.
1 Person Build
Tools Required
45*35*46CM/PINK+WHITE/WHITE+BLACK/OAK+WHITE
OTTAWA NIGHTSTAND ASSEMBLY INSTRUCTIONS
Batch No.: WMI 141036

Page 2 of 6
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
INFORMATION
•
This product is intended for a maximum weight of 50 kg.
• Due to the size of this product we recommend that it is assembled in the room intended for
use.
• When you are ready to start, make sure that you have the right tools, plenty of space and a
clean, dry area for assembly.
• Unwrap all packaging materials and place the components on top of the carton box or on a
clean floor to prevent it from scratching.
• Check the pack and make sure you have all the parts listed.
• Ensure that this product is fully assembled as illustrated before use.
• Check all screws or bolts are tightened and inspect regularly
• Tools not included.
WARNINGS
•This product should only be used on firm, level ground.
•Keep small parts out of reach of children.
•Make sure the legs remain in contact with the ground.
•Do not use power tools to construct this product.
•Do not tighten screws until fully assembled.
•Do not over tighten screws or bolts.
•Do not use this product if parts are missing, damaged or worn.
•Do not sit or stand on the product.
CARE INFORMATION
•Never use scourers, abrasives or chemical cleaners.
•To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or
detergents as they can bleach or damage the product.
Do not exceed this weight.
OTTAWA NIGHTSTAND ASSEMBLY INSTRUCTIONS
Batch No.: WMI 141036

PARTS
FITTINGS
General Hints and Tips
Ensure the arrow on the Cam is poinng towards the hole for
the Cam Bolt.Once the Cam Bolt is inserted into the Cam, turn
the Cam clockwise with a Screwdriver 90 - 180 degrees unl
secure.
Page 3 of 6
13
10 11
9
12
8
12
8
2
2
8
1
4
1
A
B
C
D
E
F
G
H
I
J
4
7
8
2
5
SCREW( 5X40mm)
DOWEL󰷅󰷅8X30mm
CAM BOLT & NUT
NAIL20MM
FOOT
RUNNER TRACK30mm
RUNNER30mm
STICKERS
HANDLE & BOLT
Parts and Fittings Checklist
Please check the pack contents before assembling this product. If any components are
missing, please contact your retailer.
The fittings pack contains small items that should be kept away from small children.
Code Item Quantity
SCREW( 3.5X14mm)
OTTAWA NIGHTSTAND ASSEMBLY INSTRUCTIONS
Batch No.: WMI 141036
LEFT HAND SIDE PANEL(1PC)
BACK PANEL(1PC)
DRAWER BOTTOM(1PC) DRAWER FRONT(1PC) TOP PANEL(1PC)
DRAWER BACK(1PC) DRAWER/LEFT HAND SIDE
PANEL(1PC)
RIGHT HAND SIDE PANEL(1PC) BOTTOM PANEL(1PC) FRONT BOTTOM CROSS
BAR(1PC)
DRAWER/ RIGHT HAND SIDE
PANEL(1PC)
6

STEP 1
STEP 2
Page 4 of 6
PARTS REQUIRED
OTTAWA NIGHTSTAND ASSEMBLY INSTRUCTIONS
Batch No.: WMI 141036
1. LEFT HAND SIDE PANEL X 1
2. RIGHT HAND SIDE PANEL X 1
1. LEFT HAND SIDE PANEL X 1
2. RIGHT HAND SIDE PANEL X 1
I. FOOT X 4
E. RUNNER TRACK X 2
C. SCREW X 6
PARTS REQUIRED
4. FRONT BOTTOM CROSS BAR X 1
3. BOTTOM PANEL X 1
A. DOWEL X 8
B. SCREW X 4󰷅
J. STICKERS X 1
I
C
E
12
A
B J
1 2
3
4

STEP 3
STEP 4
Page 5 of 5
OTTAWA NIGHTSTAND ASSEMBLY INSTRUCTIONS
Batch No.: WMI 141036
PARTS REQUIRED
11. TOP PANEL X 1
A. DOWEL X 4
D. CAM BOLT & NUT X 4
PARTS REQUIRED
5. BACK PANEL X 1
G. NAIL X 8
A
D
11
G
5

STEP 5
Page 6 of 6
OTTAWA NIGHTSTAND ASSEMBLY INSTRUCTIONS
Batch No.: WMI 141036
7. DRAWER/LEFT HAND SIDE
PANEL X 1
8. DRAWER/RIGHT HAND SIDE
PANEL X 1
6. DRAWER BACK X 1
9. DRAWER BOTTOM X 1
10. DRAWER FRONT X 1
PARTS REQUIRED
B. SCREW X 4
D. CAM BOLT & NUT X4
F. RUNNER X 2󰷅
H. HANDLE & BOLT X 1
C. SCREW X 6
F
D
9
10
C
B
6
7
8
H
COMPLETE