GFW LUCERNE OTTOMAN BED User manual

Thank you for purchasing the Lucerne ottoman bed Please read the instructions
carefully to ensure safe operation product.
Size : 4FT6IN 2270MM X 1500MM X 1380MM
5FT 2350MM X 1660MM X 1380MM
Colour : GREY
page 1 of 23
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking hazards.
Tools Required
LUCERNE OTTOMAN BED ASSEMBLY INSTRUCTIONS

page 2 of 23
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
This product is intended for a maximum person's weight of 110kg per side. Do not exceed this
weight
Incorrect installation could lead to injury, take care following instructions.
Due to the size of this product we recommend that it is assembled in the room intended for use
When you are ready to start, make sure that you have the right tools, plenty of space and a clean,
dry area for assembly
Unwrap all packaging materials and place the components on top of the carton box or on a clean
floor to prevent it from scratching
Check the pack and make sure you have all the parts listed
Ensure that this product is fully assembled and secured as illustrated before use
Check all screws or bolts are tightened and inspect regularly.
This product should only be used on firm, level ground.
Dismantle for transportation.
Only use recommended accessories.
Tools are included.
WARNINGS
When moving the bed Always lift Carefully into position NEVER DRAG OR PULL YOUR BED
OTHERWISE THIS COULD DAMAGE ESSENTIAL COMPONENTS.
DO make sure the legs remain in contact with the ground.
DO keep small parts out of reach of children.
DO NOT use power tools to construct this product.
DO NOT tighten screws until fully assembled.
DO NOT over tighten screws or bolts.
DO NOT use this product if parts are missing, damaged or worn. DO NOT stand on the product.
CARE INFORMATION
Never use scourers, abrasives or chemical cleaners
To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or
detergents as they can bleach or damage the product
LUCERNE OTTOMAN BED ASSEMBLY INSTRUCTIONS

11
17
page 3 of 23
Parts
Please check the pack contents before assembling the product. If any components are missing,please
contact your retailer. The fittings pack contains small items that should be kept away fromsmall children.
12
13
8
8
10
20 19
5
5
15
15 3
3
21
16
16
16
16
18
6
6
7
717 9
9
4
4
7
1
14
B
A
A
14
LUCERNE OTTOMAN BED ASSEMBLY INSTRUCTIONS
7

123
Description:SID E RAIL LE FT
&R IGH T PAN EL
page 4 of 23
Carton NO: 3
Qty:2 PCS
Carton NO: 2
Qty:1 PC
Carton NO: 1
Qty:1 PC
Qty: 4FT6IN:26PCS 5FT:28PCS
Description：STORAGE BASE
SUPPORT
456
789
10 11 12
13 14 15
16 17 18
19 20 21
Description:GAS LIFT
Carton NO :2
:2 PCS
Description:MATTRESS
SUPPORT :2 PCS
Carton NO :2
Description:WOODEN LEGS
Carton NO :2
:4 PCS
Carton NO :2
:4 PCS
Carton NO :2
Description:LONG SUPPORT LEG
:2 PCS
Carton NO :2
Description:HINGE LEFT & RIGHT
:2 PCS
Description:LEFT RAIL
Carton NO :3
:1 PC
Description:RIGHT RAIL
Carton NO :3
:1 PC
Carton NO :3
:1 PC
Description:BACK RAIL
Carton NO :3
Qty:1 PC
Description:CENTRE RAIL
Carton NO :2
Description:WOODEN SLAT
Qty: 2PCS
Carton NO :1
Description:STORAGE PANEL
Qty: 4PCS
Carton NO :2
Description:TRIANGLE PLATE
Qty: 2PCS
Carton NO :2
Description:HINGE'S SUPPORT
RAILS Qty: 1PC
Carton NO :1
Description:BOTTOM CROSS MDF
Description:FRONT RAIL
Qty: 1PC
Carton NO :3
Qty: 1PC
Carton NO :3
Description:BED'S CROSS RAIL
Qty: 1PC
Carton NO :3
Description:LOWER MIDDLE RAILS
Description:HEADBOARD Description:FOOTBOARD
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
LUCERNE OTTOMAN BED ASSEMBLY INSTRUCTIONS

Bolt-5/16*25mm 20
Bolt-5/16*45mm 10
4
Bolt-1/4*20mm
Bolt-1/4*57mm
27
18
Nut-5/16
Washer*5/16
Spring Washer*5/16
Washer*1/4
Spring Washer*1/4
Butterfly Nut 2
End Slat Cap 4ft6in：
26pcs. 5ft:28pcs 28/30
Centre Slat Cap 4ft6in：
13pcs. 5ft:14pcs 14/15
H
I
K
L
M
N
O
P
C
D
E
F
G
4MM Allen Key
5MM Allen Key
Spanner
J
10
40
40
47
47
10 20 30 40 50 60 70 80 90
100
page 5 of 23
1
1
1
A
B
(Not to scale)
Fixings(to scale)
Ref Qty
Dimensions
Antiskid Nut
CAUTION: There are many small components used in the construction of this product. Please keep
these components away from young children whilst assembling this product.
If you keep the fittings in a bowl during assembly you will be less likely to lose them!
LUCERNE OTTOMAN BED ASSEMBLY INSTRUCTIONS

20
LR
Turm to page 20 for fitting the hinges
！IMPORTANT PISTON INFORMATION
The pistons used in the construction of this product are extremely strong and cannot be operated by
hand when not fitted to the ottoman hinges. All pistons are tested in the factory for correct pressure
and operation before use.
Initially it might appear that the pistons are very stiff when opening and closing the ottoman frame,
THIS IS NORMAL.
After operating the ottoman a few times, the movement of the pistons and the opening and closing of the ottoman
will become easier.
page
6 of 23
LUCERNE OTTOMAN BED ASSEMBLY INSTRUCTIONS

page
7 of 23
Hints and Tips
To operate the ottoman, always use 2 hands at arm's length and only where illustrated on this product. You must
ensure the mattress is on the bed frame before lifting the mechanism. Failure to do so may result in injury.
To ensure your safety please do not stand too close in case the frame bounces up. The weight of the
mattress loaded on the frame will keep the frame in a lower position until it is pulled upwards by the user.
If removing the mattress, make sure the frame is secured so it does not flip open. When lifting the bed frame,
remove pillows and covers.
PLEASE NOTE - It takes a lot of force to make the initial movement of the ottoman - THIS IS A DESIGN
FEATURE OF THE PRODUCT SO THAT IT DOES NOT FALL SHUT - and the nearer to being closed the
ottoman is , the easier it is to move. When the ottoman is almost shut, it will close completely under its own weight.
When lowering the slat unit for the first time, take care to make sure it does not rub unevenly on the inside face of
the Side Rail. If it does, the bed has been assembled slightly out of square. This can be rectified by moving the
Footboard of the bed slightly to the left or right whilst leaving the hardboard of the bed frame stationary.
Tip for difficulty with compression:
If you are experiencing difficulty with the initial compression try fitting one piston at a time (following the Assembly
Instructions) then press down on the side of the frame with the piston fitted - this acts like a big lever (The weight
of the mattress can be used to supplement the load exerted). Effectively you are doubling the amount of force
applied, because you have halved the resistance offered by the pistons. It can take slightly more effort than you
might feel comfortable applying to the bed frame at first.
LUCERNE OTTOMAN BED ASSEMBLY INSTRUCTIONS

page
8 of 23
Do not attempt to move the bed whilst the frame is in the upright positon.
LUCERNE OTTOMAN BED ASSEMBLY INSTRUCTIONS

page
9 of 23
Layout Parts on Soft Surface
Lay out all 4 sides on a soft surface i.e.Rug,Carpet or Packaing Carton
LUCERNE OTTOMAN BED ASSEMBLY INSTRUCTIONS

page
10 of 23
STEP 1 Parts
Required
STEP 2 Parts
Required
H
G
NOX 4
1
2
G
NO
7
1.HEADBOARD X 1
2.FOOTBOARD X 1
7.STORAGE BASE
SUPPORT X 4
H X 1
G X 8
N X 8
O X 8
6.LEG X 4
12
6
LUCERNE OTTOMAN BED ASSEMBLY INSTRUCTIONS