GGM gastro WFMFC3 User manual

Sausage Stuffer
USER MANUAL
Model#：WFMFC3, WFMFC5, WFMFC7
Stainless Steel Sausage Stuffers
Please read and keep these instructions. Indoor use only.

General Safety Regulations
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions or situations that could occur. It must be understood by the operator
that common sense and caution are factors that cannot be built into this product, but must be
supplied by the operator.
Please use this machine according to these cautions. The user should understand all rules. Please
carefully read them before you operate the machine. This machine may cause harm to the health
of the operator if the user removes or changes equipment in the machine.
We are not responsible for any injuries resulting from improper operation of this machine. Please
operate according to “Operation Method” instructions and follow the proper operation procedures
while using. Take care while assembling and operating, in order to avoid scratching skin. Please
read the instruction manual.
•CHECK FOR DAMAGED PARTS. Before using the stuffer, check that all parts are operating
properly and perform the intended functions. Check for binding of moving parts, mounting
and any other conditions that may affect the operation.
•The Manufacturer declines any responsibility in the case of improper use of the stuffer.
Improper use of the stuffer will VOID the warranty.
•Repair must be done by an authorized dealer. Use only factory original parts and accessories.
Modification of the stuffer will VOID the warranty.
•Be sure the stuffer is stable during use.
•NEVER operate the stuffer with the gear housing cover open or removed.
WEAR EYE PROTECTION! Everyday eye glasses are not safety glasses. Safety glasses conform
to ANSI Z87.1 requirement. Note: Approved safety glasses have Z87 printed or stamped on
them.
•Do not use outdoors
SAVE THESE INSTRUCTIONS

Assembly and Installation
PLUNGER ASSEMBLY
1. Slide the Plunger Seal onto the Plunger (figure 1).
2. Assemble the Pressure Release Valve Kit onto the Plunger. From
the top of the Plunger, place the Washer onto the Valve Hole,
then insert the Screw through the Washer and into the Valve
Hole. From the underside of the Plunger, place the Spring onto
the end of the Screw, then place the Valve Cap onto the end of
the Screw and twist to secure.
3. Screw the Plunger Bolt onto the Plunger Shaft (figure 2).
4. Place the assembled Plunger onto the end of the Plunger Shaft
(figure 3).
STUFFER ASSEMBLY
5. Attached the Handle by sliding it onto either
the Fast or the Slow Gear (figure 4).
6. Crank the Handle to bring the Plunger to the
top of the Stuffer.
...continued on next page

STUFFER ASSEMBLY continued
7. Rest Canister’s Bottom Brackets onto the
Canister Mounts inside the Housing of the Stuffer.
Pivot the Canister fully into the Stuffer Housing,
snapping the Top Brackets into the Canister
Mounts ( figure 5).
8. Insert the Stuffing Funnel of choice through the
Front Ring Nut. Screw the Front Ring Nut and
Stuffing Funnel onto the mouth of the Canister
until snug. DO NOT OVERTIGHTEN the Front Ring
Nut, as it may damage the Funnel. ( figure 6)
9. Thoroughly coat the inside of the Canister with
a food- grade lubricant prior to use. ( figure 7)

Disassembly and Cleaning
NOTE: BE SURE TO CLEAN ALL PARTS IMMEDIATELY AFTER USE.
1. Remove the Stuffing Funnel by unscrewing the Front Ring Nut, and pulling the Funnel out.
2. Tum the Handle until the Plunger comes up and out of the Canister.
3. Pivot the Canister outward, then pull the Canister up to remove the Canister from the Stuffer
Housing.
4. Unscrew the Plunger from the Plunger Shaft.
5. Disassemble the pressure release valve from the plunger.
6. Remove the plunger seal from the plunger.
7. Wash all parts that have come in contact with meat in hot soapy water.
8. Rinse and thoroughly dry all parts immediately.
9. Sterilize as needed.
10. Fully lubricate the Shaft, Canister, Pressure-Release Valve components and the Front Ring Nut
with a food-grade lubricant before and after each use.

Stuffing Instructions
CAUTION! When the plunger is pulled out of
the Canister, RELEASE THE HANDLE SLOWLY!
Pressure or gravity could cause the Handle
to spin back slightly and cause injury.
NOTE: Apply a food-grade lubricant to the
inside of the Canister before filling with the
meat mixture.
1. Tilt out the Canister
2. Fill the Canister with the meat and seasoning mixture (figure 8).
3. Press the mixture down into the Canister firmly to release any
trapped air.
4. Pivot the Canister back into the upright position and snap the Top
Brackets onto the Canister Mounts.
5. Turn the Handle until the Plunger comes in contact with the meat
and the mixture is ready to extrude out the end of the Stuffing
Funnel
6. Slip a casing on the end of the Stuffing Funnel until the entire
casing has slid onto the Funnel.
7. Tie, twist or hog ring the end of the casing to seal it.
8. Turn the Handle to extrude the mixture into the casing.
9. For best results, apply pressure around the casing, close to the end
of the Stuffing Funnel. This will hold the casing tight and will cause
the mixture to pack firmly into the casing.
10. When the end of the casing has been reached, tie, twist or hog ring the end of the casing to
seal the contents inside.
STUFFING TIPS:
The following are suggestions to help reduce the resistance when stuffing with the
13 mm Stuffing Funnel.
A . Add up to 1½ cups (400mL) of water per every 2.3 kg of seasoned meat.
B . Add ¼ cup (60ml) of vegetable or olive oil per every 2.3 kg of seasoned meat for
better flow.

Exploded Diagram and Parts List
Part #
Description
1
Handle
2
Plunger
3
Plunger Seal
4
Pressure Release Valve (4 Piece
Set)
5
Stainless Steel Funnel Set (4
Funnels)
6
Stainless Steel Canister
7
Front Ring Nut
8
Canister Mounting Hardware Kit
(4 Sets)
9
Plunger Shaft
10
Plunger Bolt
11
Gear Housing Cover with
Hardware Kit
12
Gear Housing Cover Bottom
Plate with Hardware Kit
13
Gear Housing with Hardware Kit
14
Main Driving Gear
15
Slow Speed Control Gear
16
Fast Speed Control Gear
17
Rubber Foot (4 Piece Set)
18
Butterfly Screw