Ghost Controls AXWK User manual

1
©Ghost Controls 2020
AXWK WIRELESS KEYPAD
MANUAL
FEATURES:
1. 40 Access PINs + 1 Primary Pin
2. Xtend Access: Once a valid PIN is entered and
sent, any number key can operate the gate
for at least 30 seconds. Each key pressed restarts
the 30 second timer.
3. PartyMode: Hold gate open.
4. PartyMode Secure or 1-Key Mode: Any key on
the keypad can operate the gate.
5. VacationMode: Disable all wireless transmitter.
6. Time based temporary PINs: Automatically
expired after X number of days.
7. Number of use based Temporary PINs:
automatically expired after X number of uses.
8. Compatible with ALL Ghost Controls gate
opener system.
9. Compatible with most automatic gate systems
when used with the Ghost Controls Universal
Receiver AXUR.
TABLE OF CONTENTS
PROGRAMMING THE KEYPAD FOR THE 1ST TIME:
A. Installing the batteries (Need 2 C Batteries) _______________________________________________________2
B. Programming your PRIMARY PIN ________________________________________________________________2
C. Teaching your remote to the keypad (MUST DO) _________________________________________________3
D. Test your PRIMARY PIN__________________________________________________________________________ 3
E. Adding an ACCESS PIN __________________________________________________________________________ 3
F. Mounting the keypad ______________________________________________________________________________4
Changing your PRIMARY PIN ___________________________________________________________________________________4
Adding an ACCESS PIN _________________________________________________________________________________________4
Adding a time based temporary ACCESS PIN ____________________________________________________________________5
Adding a use based temporary ACCESS PIN _____________________________________________________________________5
Delete an ACCESS PIN__________________________________________________________________________________________6
Delete all ACCESS PINs_________________________________________________________________________________________6
Enable/disable PartyMode ________________________________________________________________________________________6
Enable/Disable PartyMode Secure or 1-Key mode ________________________________________________________________ 7
Enable/Disable VacationMode ____________________________________________________________________________________ 7
Factory reset the keypad__________________________________________________________________________________________ 7
Troubleshooting __________________________________________________________________________________________________8
NUMBER KEYS (0-9)
Use to enter numbers for
Primary and Access PIN
PARTYMODE SECURETM OR
1KEYTM (ON/OFF)
Use with PRIMARY PIN to turn
PARTYMODE SECURETM or
1KEYTM function ON/OFF
PARTYMODE® (ON/OFF)
Use with PRIMARY PIN to
turn PARTYMODE function
ON/OFF
STATUS LED
Provides visual feedback
for programming and
entering pins
VACATION MODE® (ON/OFF)
Use with PRIMARY PIN to
turn VACATIONMODE®
function ON/OFF
PROGRAM
Use to enter programming
mode to perform various
programming operations
SEND
Press after your PIN
is entered to open
gate

2©Ghost Controls 2020
IMPORTANT MUST READ BEFORE PROGRAMMING
■Make sure you have a Ghost Controls transmitter that is already programmed to operate the gate.
■You MUST CREATE a NEW PRIMARY PIN other than the factory default of ‘0000’ in order to use the keypad.
■ALL LEDs including the backlight LEDs must be OFF (Sleep mode) prior to enter any of the programming mode.
AUDIBLE INDICATORS
■Long beep (2-3 seconds) followed by 2 short beeps = PROGRAMING ERROR
■3 long beeps, pause, then 2 short beeps = PROGRAMING SUCCESSFUL
■2 beeps then turn OFF all LEDs = Unit is going into sleep mode due to inactivity.
PROGRAMMING THE KEYPAD FOR THE 1ST TIME:
A. INSTALLING THE BATTERIES: Use only C-Size Alkaline Batteries (2 needed). Energizer or Duracell recommended.
B. PROGRAMMING YOUR NEW PRIMARY PIN: (DO NOT GIVE OUT PRIMARY PIN FOR ACCESS)
PRIMARY PIN is needed to operate Partymode, 1-Key and Vacation Modes.
A. Press and Release PROGRAM BUTTON
(the PartyMode, 1-Key, Vacation LEDs come on)
B. Enter 0 0 0 0
C.Press and Release PROGRAM BUTTON
D. Enter 7 6
E. Press and Release PROGRAM BUTTON
F. Enter NEW 4 DIGIT PRIMARY PIN
YOU CAN NOT USE 0 0 0 0
G.Press and Release PROGRAM BUTTON
0
7
0
6
0 0
C BATTERY
C BATTERY

3
©Ghost Controls 2020
C. TEACHING YOUR WORKING REMOTE TO THE KEYPAD:
(MAKE SURE YOU CHANGED THE FACTORY DEFAULT
PIN OF 0000): (NOTE-IF YOU ARE CLOSE TO THE GATE, IT MAY
ACTIVATE DURING THESE STEPS.)
A. Press and Release PROGRAM BUTTON
(the PartyMode, 1-Key, Vacation LEDs come on)
B. Place the transmitter as shown and press the transmitter button
until the Party, 1-Key and Vacation LEDs on the keypad are blink-
ing in alternating sequence. (If the transmitter has already been
programmed into keypad, the unit will auto exit programing mode.
Entering PRIMARY PIN is not required.)
C.Enter your PRIMARY PIN
D. Press and Release PROGRAM BUTTON
D. TEST PRIMARY PIN TO OPERATE THE GATE. (Make sure DIP#2 on System
control board is to the right so that you can hear the WARNING from the gate
opener system.)
A. Enter your 4 DIGIT PRIMARY PIN
B. Press SEND
Once the valid access PIN and SEND is entered, the keypad will stay active for 30 seconds. During this time, the
keypad will send a ‘CYCLE’ signal to the gate upon a press of any number key. Each ‘CYCLE’ signal will cause the gate
to operate as follow:
…OPEN, STOP, CLOSE, STOP, OPEN, STOP…
After 30 seconds of inactivity, the keypad will beep twice and enter Standby Mode. This is its normal condition after
30 seconds of inactivity.
E. ADD AN ACCESS PIN FOR GUESTS: (This pin can only open and close the gate and cannot be 0 0 0 0.)
A. Press and Release PROGRAM BUTTON
(the PartyMode, 1-Key, Vacation LEDs comes on)
B. Enter your 4 DIGIT PRIMARY PIN
C.Press and Release PROGRAM BUTTON
D. Enter 2 2
E. Press and Release PROGRAM BUTTON
F. Enter NEW 4 DIGIT ACCESS PIN
G.Press and Release PROGRAM BUTTON
7 6
2 2

4©Ghost Controls 2020
6. MOUNTING THE KEYPAD
A. Keypad should be 60' or less from the gate
B. Keypad should be at least 10' outside the
path of the moving gate
C.Keypad must be in sight of the gate
CHANGING YOUR 4 DIGIT PRIMARY PIN (CANNOT USE 0 0 0 0):
A. Press and Release PROGRAM BUTTON
(the PartyMode, 1-Key, Vacation LEDs comes on)
7 6
B. Enter your PRIMARY PIN
C.Press and Release PROGRAM BUTTON
D. Enter 7 6
E. Press and Release PROGRAM BUTTON
F. Enter NEW 4 DIGIT PRIMARY PIN
YOU CAN NOT USE 0 0 0 0
G.Press and Release PROGRAM BUTTON
ADD ADDITIONAL ACCESS PINS (CANNOT USE 0 0 0 0):
A. Press and Release PROGRAM BUTTON
2 2
(the PartyMode, 1-Key, Vacation LEDs comes on)
B. Enter your PRIMARY PIN
C.Press and Release PROGRAM BUTTON
D. Enter 2 2
E. Press and Release PROGRAM BUTTON

5
©Ghost Controls 2020
F. Enter additional 4 DIGIT ACCESS PIN
G.Press and Release PROGRAM BUTTON
ADD A TIME BASED TEMPORARY
ACCESS PIN: (access pin will work for a certain number of days and cannot be 0 0 0 0)
A. Press and Release PROGRAM BUTTON
(the PartyMode, 1-Key, Vacation LEDs comes on)
B. Enter your PRIMARY PIN
C.Press and Release PROGRAM BUTTON
D. Enter 2 3
E. Press and Release PROGRAM BUTTON
F. Enter NEW TIME BASED ACCESS PIN
G.Press and Release PROGRAM BUTTON
H.Enter the NUMBER OF DAYS Allowed
EXAMPLE: for 5 days.... 0 5
I. Press and Release PROGRAM BUTTON
ADD A USE BASED TEMPORARY ACCESS PIN: (access pin will work for a number of uses)
A. Press and Release PROGRAM BUTTON
(the PartyMode, 1-Key, Vacation LEDs comes on)
B. Enter your Primary Pin
C.Press and Release PROGRAM BUTTON
D. Enter 2 8
E. Press and Release PROGRAM BUTTON
F. Enter NEW USE BASED ACCESS PIN
G.Press and Release PROGRAM BUTTON
H.Enter the NUMBER OF USES Allowed
EXAMPLE: for 5 uses.... 0 5
I. Press and Release PROGRAM BUTTON
3
D D
2
2 8
U U
7 6

6©Ghost Controls 2020
DELETE AN ACCESS PIN: (deleted pin will no longer operate the gate)
A. Press and Release PROGRAM BUTTON
(the PartyMode, 1-Key, Vacation LEDs comes on)
B. Enter your Primary Pin
C.Press and Release PROGRAM BUTTON
D. Enter 3 2
E. Press and Release PROGRAM BUTTON
F. Enter ACCESS PIN to be DELETED
G.Press and Release PROGRAM BUTTON
DELETE ALL ACCESS PINS: (ALL access pins are deleted, Primary Pin is only one able to operate
the gate)
A. Press and Release PROGRAM BUTTON
(the PartyMode, 1-Key, Vacation LEDs comes on)
3 3
B. Enter your Primary Pin
C.Press and Release PROGRAM BUTTON
D. Enter 3 3
E. Press and Release PROGRAM BUTTON
ENABLE/DISABLE PARTYMODE: (this holds your gate open)
PartyMode Enable: The gate will stay open and autoclose (if enabled) is suspended. The gate opener will BEEP TWICE if
attempting to close the gate while PartyMode is enabled.
NOTE: IF THE ABOVE DOES NOT DISABLE PARTYMODE TURN THE GATE OPENER OFF AT CONTROL BOX AND
THEN BACK ON AND THIS WILL EXIT PARTYMODE.
A. Press and Release PARTY BUTTON
B. Enter your Primary Pin
C.Press SEND
Repeat the above steps to disable PartyMode. The gate opener will BEEP THREE (3) TIMES to indicate that it is exiting
PartyMode.
3 2

7
©Ghost Controls 2020
ENABLE/DISABLE PARTYMODE SECURE OR 1-KEY MODE: (Pressing any # key on
the keypad allows guest to enter your property while keeping it secure because the gate shuts after each guest when
autoclose is set)
PartyMode Secure or 1-Key Enable: When enabled, the ‘1-Key’ will be ON and any number key will operate the gate. This mode is
useful when guest is not require to use PIN to operate the gate such as when it is installed on the inside of the property for exit.
We recommend that the Autoclose feature on the gate opener is enabled when using this feature.
A. Press and Release 1-KEY BUTTON
B. Enter your Primary Pin
C.Press SEND
Repeat the above steps to disable this Mode.
ENABLE/DISABLE VACATION MODE: (This keeps your gate closed and all remotes or codes to
keypad are Denied access to property until taken o this mode)
Vacation Mode Enable: The gate will stay closed and all RF remote devices that control the gate will not be able to open the gate.
The gate opener will BEEP TWICE if attempting to open the gate while Vacation Mode is enabled.
NOTE: IF THE ABOVE DOES NOT DISABLE VACATION MODE TURN THE GATE OPENER OFF AT CONTROL BOX AND
THEN BACK ON AND THIS WILL EXIT VACATION MODE.
A. Press and Release VACATION BUTTON
B. Enter your Primary Pin
C.Press SEND
Repeat the above steps to disable VacationMode. The gate opener will BEEP THREE (3) TIMES to indicate that it is
exiting Vacation Mode.
FACTORY RESET THE KEYPAD: (Do this only when Primary Pin has been forgotten)
■Remove one of the C Batteries from the keypad and then press any button on the keypad.
■Reinsert the battery, wait for the keypad to beep 2 times.
■Immediately press and release the PROGRAM BUTTON 3 times.
■The keypad will perform 3 long beeps followed by 2 short beeps to indicate successful factory reset.
■MUST perform "PROGRAMMING THE KEYPAD FOR THE 1ST TIME" again.
1

8©Ghost Controls 2020
TROUBLESHOOTING:
QUESTIONS ANSWERS
After entering my PIN, any key would open/close the gate.
This is normal. After valid PIN is entered and send, any
number key on the keypad will operate the gate until the
keypad returns to Standby Mode.
I did not enter a PIN, but any key would open/close the
gate.
Make sure the ‘1-Key’ button LED (Green) is not on. If
it is, then the keypad is in ‘1-Key’ mode. To disable 1-key
mode, press the ‘1-key’ button, enter the PRIMARY PIN
and press the SEND button. The ‘1-Key’ button LED
should turn o.
Why are none of my keypad keys illuminated?
Keypad is in Standby Mode.
In Standby mode, the keypad LEDs are not lit up and the
keypad requires the PRIMARY PIN or an ACCESS PIN to
be entered.
When PRIMARY PIN is used the PartyMode, 1-Key and the
Vacation Mode LEDs will be blinking in alternating sequence.
I entered a PIN, the gate opener beeps 1-time but will not
open.
The PIN you entered is invalid. The 1-beep means the gate
‘sees’ the signal but the PIN is invalid.
I entered a PIN, the gate opener beeps 2-times but will not
open.
VacationMode is enabled on the gate. See ENABLE/DIS
ABLE VACATIONMODE or turn the gate controller OFF
then back ON.
I entered a PIN, the gate opener beeps 2-times but will not
close.
PartyMode is enabled on the gate. See ENABLE/
DISABLE PARTYMODE or turn the gate controller OFF
then back ON.
When I press any key, the keypad gives 3 long beeps follow
by 2 short beeps.
The keypad is still in factory default setting. Please go to
‘PROGRAMING THE KEYPAD FOR THE 1ST TIME’ and
complete the steps.
The keypad gives 2 long beeps with all the LEDs flashing
twice randomly or when I use the keypad.
The keypad is performing a power on check when battery
1st installed. Check and change the batteries if necessary.
Do I need to reprogram everything when I change the
battery? NO
Can I have more than one keypad to control the same
gate? YES
Why did my keypad stop working? or My keypad worked
yesterday and now it does not work today? Replace two C-size batteries in keypad.

9
©Ghost Controls 2020
BUILD A SYSTEM
(AXLC) LOCKING CLEVIS PIN
Pin De Bloqueo De Bloqueo
FIRST GATE OPENER
Primer Abridor De Puerta
SECOND GATE OPENER
Segundo Abridor De Puerta
LEGEND | LEYENDA
INCLUDED IN KIT
Incluido En El Kit
ADDITIONAL ACCESSORIES
Accesorios Adicionales
(AXZL) ZOMBIELOCK GATE LOCK
Bloqueo De Puerta Zombielock
(AXTB) TUBE GATE BRACKETS
Soportes De Puerta De Tubo
(AXPB) PUSHBUTTON
Presionar El Botón
(AXLV) LOW VOLTAGE WIRE
Alambre De Bajo Voltaje
(ABBT2) BATTERY BOX KIT
Kit De Caja De Batería
CONTROL BOX
Caja De Control
(AXDP) 10 W SOLAR PANEL
Panel Solar De 10 W
(AXGN) OUTDOOR PEDESTAL
Pedestal Al aire Libre
(AXWK) WIRELESS KEYPAD
Teclado Inalámbrico
WARNING PLACARD
Rótulo de advertencia
(AXXV) WIRED VEHICLE SENSOR
Sensor De Vehiculo Con Cable
(AXWV) WIRELESS VEHICLE SENSOR
Sensor De Vehículo Inalámbrico
(AXS1)
STANDARD REMOTE
Control Remoto Estándar
(AXP1)
PREMIUM REMOTE
Control Remoto Premium
(AXR1)
WEATHER-RESISTANT REMOTE
Control Remoto Resistente
A LaIntemperie
OUTSIDE OF PROPERTY
Fuera De La Propiedad
INSIDE OF PROPERTY
Dentro De La Propiedad

10 ©Ghost Controls 2020
ADD YOUR PINS HERE
PRIMARY
PIN
ACCESS PIN
ACCESS PIN
ACCESS PIN
GhostControls.com
Made in China, AXWKIM | Rev. 2021-01
©2020 GHOST CONTROLS®
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer.
For more information, go to www.P65Warnings.ca.gov
WARNING
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.