Gianni Industries DG-200 User manual

Copyright All Rights Reserved.
P-MU-DG-200 Ver. A Publish: 2009.11.30 Page: - 1 -/ 5
DG-200 Digital Keypad
Operation Manual
Unit: (mm)
I. Features:
1. Allows up to 200+10 PINs.
2. 29-digit-code password protected design.
3. Lockout for 60 seconds after entering 5 times invalid PINs (The keypad without
beep sound during the period time).
4. 3 LED indicators & buzzer for status indication. Keypad with beep sound.
5. Metal case & stainless steel panel designed with mechanical key lock designed
for easy wiring & maintenance, enhanced safety and durability.
6. Weather resistance for outdoor applications.
7. Additional input for anti-tailgating function to ensure high security access control.
8. Non-volatile memory stores all code settings for a long time, even in the event of
total power failure.
9. Dual relays to control door lock and other security devices.
10. Built-in tamper switch.

Copyright © Gianni industries, inc. All Rights Reserved.
P-MU-DG-200 Ver. A Publish: 2009.11.30 Page: - 2 -/ 5
II. Specifications:
Operating Voltage
12~24VAC/DC
Current Draw
＊Holding : 22mA, Pull-In: 66mA@12VAC/DC
＊Holding: 12mA, Pull-In: 32mA@24VAC/DC
Keypad
4X3 matrix backlit 12-digit (0~9,＊,＃)
Input
1 contact for Request-To-Exit button
1 contact for Door Reed Switch
Output
2 relays (N.O. / N.C. / Com. Dry contacts)
Relay Electric Current
Max. 12A@14VDC, 7A@120VAC
Memory Volume
200+10 PINs
Relay Strike Time
01~99 seconds, Toggle mode(00)
LED Status Indication
3 LED indicators display (Red/Yellow/Green
)
Ambient Humidity
5%~95% (Non-condensing)
Operating Temperature
-20°C~+70°C
III. Status Indication & Default Setting Parameters:
Mode Status
Green First relay active
Red Second relay active
LED
Yellow Normal (Power On)
1 Short Beep Key in
1 Long Beep Valid PINs
2 Beeps Enter / exit programming mode
3 Beeps Incorrect input
Beep
5 Beeps Reset master code to default value (12345)
,
clear all PINs
IV. Factory Default Setting:
Master Code
12345 (5 digits)
Relay Strike Time (Time Delay Setting)
5 seconds
Pressed Key Time Delay
5 seconds (Fixed)
Programming Mode Time Delay
25 seconds (Fixed)
PIN digits
5~8 digits

Copyright © Gianni industries, inc. All Rights Reserved.
P-MU-DG-200 Ver. A Publish: 2009.11.30 Page: - 3 -/ 5
V. Operation Instruction:
The master code comprises of a five-digit number and is used to access
programming functions of the digital keypad and cannot be used for access i.e. It
cannot be the same as other PINs. The default master code is set to 12345. Under
normal operation the keypad is used for entering PIN to gain access. In the
programming mode, the keypad can be used to add/delete PINs, set relay strike time
and other operation functions.
1. Enter programming mode：
Enter the master code twice 12345 12345 to enter programming mode (1 beep,
rapid yellow LED flash). (If no data is entered within 50 seconds, the system will exit
programming mode; or press # to exit the programming mode).
2. Setting the Relay Strike Time
The relay strike time determines the amount of time that the door remains unlocked
after a valid PIN is entered.
NOTE: Enter 00 will set the relay strike time to 0 second (relay set to toggle
mode)
1. Enter programming mode
2. Press ＊300 for Relay 1 (rapid green LED flash) → Enter 00~99 (1 beep, green
LED stay on)
Press ＊400 for Relay 2 (rapid red LED flash) → Enter 00~99 (1 beep, red LED
stay on)
3. Press # (1 beep) back to programming mode
4. Press # again (1 beep) back to standby mode (slow yellow LED flash)
3. Clear Memory of All PINs of Relay 1
1. Enter programming mode
2. Press ＊888 (green LED stay on)
3. Press 00 (rapid green LED flash, 5 beeps)
4. Press # (1 beep) back to programming mode
5. Press # again (1 beep) back to standby mode (slow yellow LED flash)
4. Clear Memory of All PINs of Relay 2
1. Enter programming mode
2. Press ＊999 (red LED stay on)
3. Press 00 (rapid red LED flash, 5 beeps)
4. Press # (1 beep) back to programming mode.
5. Press # again (1 beep) back to standby mode (slow yellow LED flash)

Copyright © Gianni industries, inc. All Rights Reserved.
P-MU-DG-200 Ver. A Publish: 2009.11.30 Page: - 4 -/ 5
5. Adding PINs to Relay 1
a:
1. Enter programming mode to select slot position ＊001~＊200 (rapid green LED
flash to indicate the slot position is available)
2. Enter new PIN (1 beep, green LED stay on)
3. Press # (1 beep) back to programming mode
4. Press # again (1 beep) back to standby mode (slow yellow LED flash)
b:
1. Enter programming mode to select slot position ＊001~＊200 (green LED stay
on to indicate the slot position is unavailable)
2. Press 00000 (1 beep) delete the data from the slot position (rapid green LED
flash)
3. Repeat the steps of 5-a to add new PINs.
6. Adding PINs to Relay 2
a:
1. Enter programming mode to select slot position ＊201~＊210 (rapid red LED
flash to indicate the slot position is available)
2. Enter new PIN (1 beep, red LED stay on)
3. Press # (1 beep) back to programming mode
4. Press # again (1 beep) back to standby mode (slow yellow LED flash)
b:
1. Enter programming mode to select slot position ＊201~＊210 (red LED stay on
to indicate the slot position is unavailable)
2. Press 00000 (1 beep) delete the data from the slot position (rapid red LED flash)
3. Repeat the steps of 6-a to add new PINs.
7. Change Master Code
1. Enter programming mode.
2. Press ＊000 + XXXXX (5-digit master code), 1 beep, yellow LED stay on.
3. Press # (1 beep) back to programming mode.
4. Press # again (1 beep) back to standby mode, slow yellow LED flash.
8. Change PIN length
1. Enter programming mode
2. Press ＊555 + 5~8-digit code, then press # to exit programming mode.

Copyright © Gianni industries, inc. All Rights Reserved.
P-MU-DG-200 Ver. A Publish: 2009.11.30 Page: - 5 -/ 5
VI. Wiring Diagram:
NOTE:
1. It is suggested to use #22~26 AWG insulation wire.
2. The door strike or relay must have a varistor or a diode across the door strike
terminals to suppress the back EMF of the strike - failure to do so will damage the
relay contacts and electronic components, or even burns the controller.
Warranty:
The product is warranted against defects in material and workmanship while used in
normal service for a period of 1 year from the date of sale to the original customer.
The GEM policy is one of continual development and improvement; therefore GEM
reserves the right to change specifications without notice.