Gigabyte TO23-H60 User manual

TO23-H60
3rd Generation Intel® Xeon® Scalable OCP Compute Node
2OU 3Nodes 4-bay NVMe/SATA/SAS
TO23-BT0
2OU ORV3 Node Tray
User Manual
Rev. 1.0

Copyright
© 2022 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specications and features in this manual may be made by GIGABYTE without
prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classications
In order to assist in the use of this product, GIGABYTE provides the following types of documentation:
 User Manual: detailed information & steps about the installation, conguration and use of this
product (e.g. motherboard, server barebones), covering hardware and BIOS.

User Guide: detailed information about the installation & use of an add-on hardware or
software component (e.g. BMC rmware, rail-kit) compatible with this product.
Quick Installation Guide: a short guide with visual diagrams that you can reference easily for
installation purposes of this product (e.g. motherboard, server barebones).
Please see the support section of the online product page to check the current availability of these
documents.
For More Information
For related product specications, the latest rmware and software, and other information please visit our website at
http://www.gigabyte.com
For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller
portal: http://reseller.b2b.gigabyte.com
For further technical assistance, please contact your GIGABYTE representative or visit
https://esupport.gigabyte.com/ to create a new support ticket
For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email:
server[email protected]

Conventions
The following conventions are used in this user's guide:
NOTE!
Pieces of additional
information related to the current topic.
CAUTION!
Precautionary measures to
avoid possible hardware or software problems.
WARNING!
Alerts to any damage that might
result from doing or not doing specic actions.

Server Warnings and Cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING!
To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from
the server.
WARNING!
To reduce the risk of personal injury from hot surfaces, allow the drives and the internal
system components to cool before touching them.
WARNING!
This server is equipped with high speed fans. Keep away from hazardous moving fan
blades during servicing.
CAUTION!
• Do not operate the server for long periods with the access panel open or removed. Operat-
ing the server in this manner results in improper airow and improper cooling that can lead to
thermal damage.
• Danger of explosion if battery is incorrectly replaced.
• Replace battery with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to the manufacturer’s instructions.
CAUTION!
Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery
only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-
teries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)
CAUTION!
ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU
PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,
PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-
TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER
WHEN HANDLING PARTS.
Always handle boards carefully, they can be extremely sensitive to ESD. Hold boards only by
their edges without touching any components or connectors. After removing a board from its
protective ESD bag or from the system, place the board component side up on a grounded, static
free surface. Use a conductive foam pad if available but not the ESD bag. Do not slide the board
over any surface.
System power on/off: To service components within the server, please ensure the power has
been disconnected.
e.g. Remove the node from the server chassis (to disconnect power) or disconnect the power
from the server chassis.
Make sure the system is removed from the rack before opening the chassis, adding, or removing
any non hot-plug components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be present
on power, telephone, and communication cables. Turn off the system chassis and disconnect the
cables attached to the system before servicing the chassis. Otherwise, personal injury or equip-
ment damage can result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage drives, boards, and
other parts. We recommend that you perform all procedures in this chapter only at an ESD work-
station. If one is not available, provide some ESD protection by wearing an antistatic wrist strap
attached to chassis ground (any unpainted metal surface on the server) when handling parts.
ESD and handling boards: Always handle boards carefully. They can be extremely sensi-tive to
electrostatic discharge (ESD). Hold boards only by their edges. After removing a board from its
protective wrapper or from the system, place the board component side up on a grounded, static
free surface. Use a conductive foam pad if available but not the board wrapper. Do not slide
board over any surface.

Installing or removing jumpers: A jumper is a small plastic encased conductor that slips over
two jumper pins. Some jumpers have a small tab on top that can be gripped with n-gertips or
with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when us-
ing needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with the
pliers, never the wide sides. Gripping the wide sides can dam-age the contacts inside the jumper,
causing intermittent problems with the function con-trolled by that jumper. Take care to grip with,
but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the board may
bend or break.

- 7 -
Table of Contents
Chapter 1 Hardware Installation ................................................................................... 11
1-1 Installation Precautions.................................................................................. 11
1-2 Product Specications.................................................................................... 12
1-2-1 TO23-H60...............................................................................................................12
1-2-2 TO23-BT0...............................................................................................................13
1-3 System Block Diagram................................................................................... 14
Chapter 2 System Appearance.....................................................................................15
2-1 Front View...................................................................................................... 15
2-2 Rear View....................................................................................................... 16
2-3 Front Panel LEDs and Buttons....................................................................... 17
2-4 Front System LAN LEDs................................................................................ 18
2-5 Hard Disk Drive LEDs .................................................................................... 19
Chapter 3 System Hardware Installation ......................................................................20
3-1 Removing Shelf from the Rack ...................................................................... 21
3-2 Removing Computing Node from the Shelf.................................................... 22
3-3 Removing System Cover ............................................................................... 23
3-4 Installing the Hard Disk Drive......................................................................... 24
3-4-1 Removing Hard Disk Drive Cage............................................................................25
3-5 Installing the CPU and Heat Sink................................................................... 26
3-6 Installing Memory........................................................................................... 28
3-6-1 Eight Channel Memory Conguration.....................................................................28
3-6-2 Removing and Installing a Memory Module ...........................................................28
3-6-3 Processor and Memory Module Matrix Table .........................................................29
3-6-4 Memory Population Table .......................................................................................29
3-7 Installing the PCI Expansion Card ................................................................. 30
3-8 Installing the Mezzanine Card........................................................................ 32
3-8-1 Installing the OCP 3.0 Mezzanine Card .................................................................32
3-9 Replacing the Fan Assembly.......................................................................... 33
3-10 Cable Routing .............................................................................................. 34
Chapter 4 Motherboard Components ...........................................................................36
4-1 Motherboard Components ............................................................................. 36
4-2 Jumper Setting .............................................................................................. 37
4-3 Backplane Board Storage Connector............................................................. 38
4-3-1 COBP540 ...............................................................................................................38

- 8 -
Chapter 5 BIOS Setup ..................................................................................................41
5-1 The Main Menu .............................................................................................. 43
5-2 Advanced Menu ............................................................................................. 46
5-2-1 Trusted Computing .................................................................................................47
5-2-2 Serial Port Console Redirection .............................................................................48
5-2-3 SIO Conguration...................................................................................................51
5-2-4 PCI Subsystem Settings.........................................................................................52
5-2-5 USB Conguration..................................................................................................54
5-2-6 Network Stack Conguration ..................................................................................55
5-2-7 Post Report Conguration ......................................................................................56
5-2-8 NVMe Conguration ...............................................................................................57
5-2-9 Chipset Conguration .............................................................................................58
5-2-10 Tls Auth Conguration ............................................................................................59
5-2-11 iSCSI Conguration................................................................................................60
5-2-12 Broadcom Gigabit Ethernet BCM5720 ...................................................................61
5-2-13 VLAN Conguration................................................................................................63
5-2-14 IPv4 Network Conguration....................................................................................64
5-2-15 Intel(R) I350 Gigabit Network Connection ..............................................................65
5-2-16 VLAN Conguration................................................................................................67
5-2-17 IPv4 Network Conguration....................................................................................68
5-2-18 Driver Health...........................................................................................................69
5-3 Chipset Menu................................................................................................. 70
5-3-1 Processor Conguration .........................................................................................71
5-3-2 Common RefCode Conguration ...........................................................................74
5-3-3 UPI Conguration ...................................................................................................76
5-3-4 Memory Conguration ............................................................................................78
5-3-5 IIO Conguration ....................................................................................................81
5-3-6 Advanced Power Management Conguration ........................................................83
5-3-7 PCH Conguration..................................................................................................85
5-3-8 Miscellaneous Conguration ..................................................................................87
5-3-9 Server ME Conguration ........................................................................................88
5-3-10 Runtime Error Logging Settings .............................................................................89
5-3-11 Power Policy...........................................................................................................91
5-4 Server Management Menu............................................................................. 93
5-4-1 System Event Log ..................................................................................................95
5-4-2 View FRU Information ............................................................................................96
5-4-3 BMC VLAN Conguration.......................................................................................97
5-4-4 BMC Network Conguration ...................................................................................98
5-4-5 IPv6 BMC Network Conguration...........................................................................99
5-5 Security Menu .............................................................................................. 100
5-5-1 Secure Boot .........................................................................................................101

- 9 -
5-6 Boot Menu.................................................................................................... 104
5-7 Save & Exit Menu......................................................................................... 106
5-8 BIOS Recovery ............................................................................................ 108
5-9 BIOS POST Beep code (AMI standard)....................................................... 109
5-9-1 PEI Beep Codes...................................................................................................109
5-9-2 DXE Beep Codes .................................................................................................109

- 10 -
This page intentionally left blank

- 11 -
Hardware Installation
1-1 Installation Precautions
The motherboard/system contain numerous delicate electronic circuits and components which
can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully
read the service guide and follow these procedures:
• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
• When connecting hardware components to the internal connectors on the motherboard,
make sure they are connected tightly and securely.
• When handling the motherboard, avoid touching any metal leads or connectors.
• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist
strap, keep your hands dry and rst touch a metal object to eliminate static electricity.
•
Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
• Before unplugging the power supply cable from the motherboard, make sure the power
supply has been turned off.
• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
• Before using the product, please verify that all cables and power connectors of your
hardware components are connected.
• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
• Do not place the computer system on an uneven surface
.
• Do not place the computer system in a high-temperature environment.
• Turning on the computer power during the installation process can lead to damage to
system components as well as physical harm to the user.
• If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certied computer technician.
Chapter 1 Hardware Installation

Hardware Installation
- 12 -
1-2 Product Specications
1-2-1 TO23-H60
Socket
Socket
Security
Security Server Operating Properties
Power SupplySystem fan
System
Dimension
3 Nodes/ 2OU
180 (W) x 90 (H) x 740(D) mm
Socket
Socket
Security
Security Server Operating Properties
Power SupplySystem fan
CPU 3rd Generation Intel® Xeon® Scalable Processors
Intel® Xeon® Platinum Processor, Intel® Xeon® Gold Processor, Intel® Xeon®
Silver Processor
Dual processor, 10nm technology
CPU TDP up to 270W
NOTE: If only 1 CPU is installed, some PCIe or memory functions might be
unavailable
Memory 16 x DIMM slots
DDR4 memory supported only
8-channel memory architecture per processor
RDIMM modules up to 128GB supported
LRDIMM modules up to 128GB supported
3DS RDIMM/LRDIMM modules up to 256GB supported
1.2V modules: 3200/2933/2666 MHz
LAN 1 x 10/100/1000 management LAN
Video Integrated in Aspeed® AST2600
2D Video Graphic Adapter with PCIe bus interface
1920x1200@60Hz 32bpp, DDR4 SDRAM
Storage 4 x 2.5" Gen4 NVMe/SATA/SAS hot-swappable bays
SAS card is required for SAS devices support
SAS Depends on SAS Add-on card
RAID Intel® SATA RAID 0/ 1/ 10/ 5
Expansion Slot Riser Card CRSH01E:
1 x PCIe x16 (Gen4 x16) low-prole slot, from CPU_0
Riser Card CRSH01H:
1 x PCIe x16 (Gen4 x16) low-prole slot, from CPU_0
1 x OCP 3.0 slot with PCIe Gen4 x16 bandwidth, from CPU_0
NCSI function supported
NOTE:
We reserve the right to make any changes to the product specications and product-related
information without prior notice.

- 13 -
Hardware Installation
Front I/O 2 x USB 3.2 Gen1
1 x VGA
1 x MLAN
1 x Power button with LED
1 x ID button with LED
1 x System status LED
Rear I/O N/A
Socket
Socket
Security
Security Server Operating Properties
Power SupplySystem fan
Power Supply 48V DC Bus Bar power solution
System
Management
Aspeed® AST2600 management controller
GIGABYTE Management Console (AMI MegaRAC SP-X) web interface
Dashboard
HTML5 KVM
Sensor Monitor (Voltage, RPM, Temperature, CPU Status …etc.)
Sensor Reading History Data
FRU Information
SEL Log in Linear Storage / Circular Storage Policy
Hardware Inventory
Fan Prole
System Firewall
Power Consumption
Power Control
LDAP / AD / RADIUS Support
Backup & Restore Conguration
Remote BIOS/BMC/CPLD Update
Event Log Filter
User Management
Media Redirection Settings
PAM Order Settings
SSL Settings
SMTP Settings
Socket
Socket
Security
Security Server Operating Properties
Power SupplySystem fan
Operating
Properties
2 x 80x80x38mm (14,900rpm)
1-2-2 TO23-BT0
Socket
Socket
Security
Security Server Operating Properties
Power SupplySystem fan
System
Dimension
803 (W) x 537 (H) x 93.2 (D) mm
2OU Node Tray
For 3 x ORV3 2OU nodes
Socket
Socket
Security
Security Server Operating Properties
Power SupplySystem fan
Open Rack
Version
ORV3
Socket
Socket
Security
Security Server Operating Properties
Power SupplySystem fan
No. of Bus
Bars
1 Bus Bar with 48V

Hardware Installation
- 14 -
1-3 System Block Diagram
2 x USB 3.2 Gen1
2 x USB 3.2 Gen1
SlimLine
DMI3 x 4
8-Channel DDR4, 8 x DIMMs
Up to 3200MHz
8-Channel DDR4, 8 x DIMMs
Up to 3200MHz
Board to
Board Conn.
PCIe 4.0 x16 slot
Riser Card
PCIe 4.0 x16 slot
Riser Card
PCIe4.0
x
16
PCIe4.0
x
16
PCIe4.0 x 16
4-bay 2.5" Gen4 NVMe/SATA/SAS
PCIe4.0 x 16
Board to
Board Conn.
OCP 3.0 Mezzanine
PCIe3.0 x 1
eSPI
2 x USB 2.0
SPI Flash
64 MB
SDRAM
4Gb
SPI Flash
64 MB
VGA
COM
SATAIII x6
NCSI
SPI
TPM
PCH
Intel C621A
chipset
ASPEED
AST2600
BMC
MLAN
10/100/1G
PHY
MAC
NVMe x4
SATA x4
CPU0
3rd Gen Intel®Xeon®
Scalable processors
(LGA4189 Socket)
3rd Gen Intel®Xeon®
Scalable processors
(LGA4189 Socket)
CPU1
3 x UPI 11.2GT/s (ICX)

- 15 -
System Appearance
Chapter 2 System Appearance
2-1 Front View
No. Description
1. Front Panel LEDs
2. ID Button with LED
3. 2 x USB 3.2 Gen1
4. VGA Port
5. Server Management LAN Port
6. PCIe Card Slot
7. OCP 3.0 Slot (Option/SFF)
8. PCIe Card Slot
Note! Drives with green latches support NVMe.
• Refer to section 2-3 Front Panel LEDs and Buttons for a detailed description of the
function of the LEDs.
1
234578
HDD0
HDD1
SLOT1
HDD2
HDD3
SLOT2
6

System Appearance
- 16 -
2-2 Rear View
1
No. Description
1. Power Distribution Board to Bus Bar Connector

- 17 -
System Appearance
2-3 Front Panel LEDs and Buttons
1
2
3
No. Name Color Status Description
1. System
Status LED
This LED represents the RoT function LED behavior.
Please see the following section for detail LED behavior.
2. Power button
with LED
Green On Indicates the system is powered on.
Green Blink System is in ACPI S1 state (sleep mode).
N/A Off - System is not powered on or in ACPI S5 state (power off)
- System is in ACPI S4 state (hibernate mode)
3. ID Button
with LED
Blue On Indicates the system identication is active.
N/A Off Indicates the system identication is disabled.

System Appearance
- 18 -
2-4 Front System LAN LEDs
No. Name Color Status Description
1. 1GbE Speed
LED
Yellow On 1 Gbps data rate
Green On 100 Mbps data rate
N/A Off 10 Mbps data rate
2. 1GbE Link /
Activity LED
Green On Link between system and network or no access
Blink Data transmission or reception is occurring.
N/A Off No data transmission or reception is occurring.
1 2

System Appearance
- 19 -
2-5 Hard Disk Drive LEDs
2.5” HD
D
LED #1
LED #2
RAID SKU LED #1 Locate HDD
Fault Rebuilding HDD Access HDD Present (No Access)
No RAID
conguration
(via HBA)
Disk LED (LED
on Back Panel)
Green ON(*1) OFF BLINK (*2) OFF
Amber OFF OFF OFF OFF
Removed HDD
Slot (LED on
Back Panel)
Green ON(*1) OFF -- --
Amber OFF OFF -- --
RAID
conguration
(via HW RAID
Card or SW
RAID Card)
Disk LED
Green ON OFF BLINK (*2) OFF
Amber OFF ON (Low Speed:
2 Hz) OFF OFF
Removed
HDD Slot
Green ON(*1) OFF (*3) -- --
Amber OFF ON (*3) -- --
NOTE:
*1: Depends on HBA/Utility Spec.
*2: Blink cycle depends on HDD's activity signal.
*3: If HDD is pulled out during rebuilding, the disk status of this HDD is regarded as faulty.
LED #2 HDD Present No HDD
Green ON OFF

- 20 -
System Hardware Installation
Pre-installation Instructions
Computer components and electronic circuit boards can be damaged by discharges of static
electricity. Working on computers that are still connected to a power supply can be extremely
dangerous. Follow the simple guidelines below to avoid damage to your computer or injury to
yourself.
• Always disconnect the computer from the power outlet whenever you are working inside
the computer case.
• If possible, wear a grounded wrist strap when you are working inside the computer case.
Alternatively, discharge any static electricity by touching the bare metal system of the
computer case, or the bare metal body of any other grounded appliance.
• Hold electronic circuit boards by the edges only. Do not touch the components on the
board unless it is necessary to do so. Do not ex or stress the circuit board.
• Leave all components inside the static-proof packaging until you are ready to use the
component for the installation.
Chapter 3 System Hardware Installation