Gigabyte GH-ESB21-TH User manual

GH-ESB21-TH
REV.1001
Intel®Pentium®4 LGA775
Installation Guide
050916

- 2 -
GH-ESB21-TH
English
Table of Contents
Checklist.............................................................................................................3
Specification........................................................................................................4
Feature..............................................................................................................4
Precautions........................................................................................................5
Warranty Item.....................................................................................................5
Installation Instructions for P4 LGA775 & Cooler.................................................6

- 3 - GH-ESB21-TH
English
Checklist
(2) GH-ESB21-TH
Installation Guide x 1
(1) GH-ESB21-TH
Cooler x 1
(4) Screw x 4
(3) Grease x 1

- 4 -
GH-ESB21-TH
English
yFan Dimension : 92 x 92 x 38 mm
yHeat Sink Dimension : 86 x 123 x 71 mm
yMaterial : Extrusion Aluminum fin + Copper core
yFan Speed Control: PWM & Temperature Control
yConnector: 4 pin
yRated Voltage : 12V
ySupports Intel BTX Type I Cooler (Supports Intel BTX & Micro BTX System)
yLarge 5 cm copper core insert. Powerful thermal ability
yFully compliant with Intel PWM & Temperature Sensor Control thermal functions
yProvide quieter environment & higher performance than box cooler
yEasy and quick installation
yRated Current : 1.13Amp (max)
yAirflow : 91.71 CFM ( max )
yBearing type : Two Ball Bearing
yLife Expectancy : 70,000 hr
yTotal Weight : 1120 g
yApplication : Intel®Pentium®4 LGA775
Feature
Specification
Fan Speed Mode
Air Inlet Temperature 25OC25
OC25 OC35 OC35 OC
PWM Duty Cycle < 20% 50% 100% < 20% 100%
Fan Speed (RPM) 900 2350 3500 900 4500
Noise (dBA) 19 35.2 45.9 19 51.2

- 5 - GH-ESB21-TH
English
<Warranty coverage does not include the following>
Incorrect method of operation or use of product not for intended use.
Operational use beyond the advised standards (eg. overclocking).
Inability to install the product as a result of incompatibility with the motherboard used.
Damage of product as a result of other product components.
Any form of alteration to original product.
A faulty product that leads to harm or damage to other products.
Damage caused by natural disasters (eg. earthquake, fire, flood).
Products with a warranty sticker that is removed, torn or unreadable.
Due to the weight of the cooler exceeding normal standards, please remove the cooler before computer transport
to prevent damage to the cooler itself as well as prevent problems during installtion.
The cooler fan speed levels provided are for reference use only. Please refer to the motherboard BIOS to
verify actual fan speed levels.
Before use, please remove the bottom protective layer of the cooler.
Please make sure the computer is turned off and its power disconnected prior to installation.
Precautions
Warranty Item

- 6 -
GH-ESB21-TH
English
Installation Instructions for P4 LGA775 & Cooler
Fig.2
Install the motherboard in the chassis. Align the GH-ESB21-TH Cooler with the screw holes and
place it onto the motherboard.
Fig.4
Finally, please attach the power connector of the cooler to the CPU fan header located on the
motherboard.
Fig.3
Fasten the cooler with screws(Note). Assure that the cooler is securely attached to the
motherboard and chassis.
Fig.1
Apply an even layer of thermal paste on the surface of the installed CPU.
Before use, please remove the bottom protective layer of the cooler.

- 7 - GH-ESB21-TH
English
(Note) The four screws can be screwed as below:
Combination 1: A+C+D+F or Combination 2: B+C+E+F
B
AC
DEF

- 8 -
GH-ESB21-TH
English