Gira System 3000 User manual

System 3000
Presence and motion detector 360° top unit BT
Presence and motion detector 360° top unit BT
Order no.: 5377 02
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. Always disconnect before carrying out work on the device or load. In
so doing, take all the circuit breakers into account, which support dangerous voltages to the
device and or load.
Danger of electric shock. The device is not suitable for disconnection from supply voltage. De-
pending on the insert used, the load is not electrically isolated from the mains, even when the
device is switched off.
Do not press on the sensor window. Device can be damaged.
The device is not suitable for use as a burglar alarm or other alarm.
These instructions are an integral part of the product, and must remain with the end customer.
2 Device components
Figure1: Device components
(1) FMinsert
(2) Sensor top
(3) Brightness sensor
(4) Button Bluetooth Ʃ
(5) Sensor window and status LEDs
(6) Decor ring
(7) Push-on cover
Status LED
Red LED lights up Self-test
Red LED flashes 3 s on / 3 s off Alarm function active
1 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Red LED flashes 0.5 s on / 0.5 s off Alarm was triggered
Red LED flashes three times followed by a 1 s
pause
Cover was previously connected to another in-
sert
Yellow LED lights up "Off" or "Off for 0.5 - 5 hours" function active
Yellow LED flashes Presence simulation active
Green LED lights up "On" or "On for 0.5 - 5 hours" function active
Blue LED lights up Device is coupled with a mobile end device
and active app
Blue LED flashes 0.5 s on / 0.5 s off Bluetooth coupling mode active
3 Intended use
– Automatic switching of lighting depending on the heat motion and ambient brightness
– Operation with flush-mounted insert for dimming or switching or 3-wire extension
– Ceiling installation on flush-mounted insert.
Product characteristics
Functions directly on the cover
– Extension of the detection area in combination with 3-wire extension
– Operation with 2-wire or 3-wire extension, rotary dimmer extension or push-button
– Dimming light via extension with dimming insert
– Resetting to factory setting
– Push-on cover for limiting the detection field
Functions via app
– Setting the device as presence detector or motion detector
– Setting the brightness threshold
– Separate adjustment of the sensitivity of the three PIR sensors
– Setting the run-on time
– Continuous ON, Continuous OFF
– Timer ON or OFF for 0.5 - 5 hours
– Switch-off pre-warning
– Dynamic run-on time
– Presence simulation
– Alarm function
– Timer function
– Walking test
In combination with a switch insert
– Short time operation
In combination with a dimming insert
– Switch on with last saved brightness or saved switch-on brightness
– Adjusting the minimum brightness
– Adjusting the maximum brightness
– Basic light function
– Night light function
– Constant light regulation
Automatic operation
The device detects heat motions of people, animals and objects.
2 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
– The light is switched on if a person enters the detection field and the brightness threshold
is below the set brightness threshold.
– The run-on time restarts with each detected motion.
– The light is switched off, if:
no more movement is detected in the detection field and the run-on time has elapsed or
the ambient light is too bright and the run-on time has elapsed.
To avoid any switch-on caused by a cooling illuminant, no movement signals are evaluated for a
brief lockout time after switching off. The motion detector adjusts itself to the ambient conditions
to keep the time as short as possible.
Behaviour after a mains voltage failure
After mains voltage return, the device performs a self-test for a maximum of 20 seconds. After
the self-test has been completed, the device is ready for operation.
If the red status LED flashes three times at repeated intervals, the cover was previously
connected to another insert. To enable the function again, either place the cover onto the
respective insert or press the Bluetooth button (4) for longer than 4 seconds.
The following applies during the self-test:
– The red status LED is illuminated.
– The load is switched off.
– Movements are not detected
– The device can be operated via extensions
4 Commissioning
Install app on a mobile end device
Requirement for operation via app is a mobile end device with Bluetooth interface, running the
Android operating system or iOS.
￭ Download and install the Gira System 3000 app from the iTunes App Store (iOS) or the
Google Play Store (Android).
Couple mobile end devices via Bluetooth
Precondition: insert and cover must be ready for operation. The mobile end device is located
close to the cover.
￭ Activate coupling mode: Press the Bluetooth Ʃ button (4) (Figure 1) for more than 4
seconds.
The blue LED flashes. The coupling mode is active for one minute.
￭ Start the app and search for device to be coupled.
Cover is coupled with the end device and shown in the app.
The coupling mode is automatically exited after successful coupling. The blue LED lights
up to confirm an active connection.
A maximum of 8 mobile end devices can be coupled with a cover. When coupling the 9th
device, the oldest device will be deleted.
5 Operation
The app is used for the configuration and operation of the device. Some basic functions can
also be operated via connected extensions.
Operation using 2-wire or 3-wire extension with button cover or push-button
Multiple extensions can be combined with each other. All operations described here are also
possible via the app. Operation with the rotary dimmer extension is described in the rotary dim-
mer extension instructions.
3 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Switching on light for the duration of the run-on time
Short-time operation: When pressed, pulses are generated approx. every 3 seconds for 1
minute. Exception for 3-wire extension: only one pulse is generated.
￭ Press the button cover or push-button briefly.
Motion detector operation: If the button cover or push-button is pressed again after
switching on, the run-on time is restarted. In combination with a dimming insert, switch-on
brightness is switched on again.
Switching the light off for 3 minutes
This function can only be used in presence detector operation.
￭ Press the button cover at the bottom or push-button briefly.
The light is switched off for the period of 3 minutes. When movements are detected, the
time is restarted.
Adjust the brightness, only in combination with dimming insert
￭ Long press on button cover at the top or bottom or push-button.
Save switch-on brightness, only in combination with dimming insert
￭ Adjust the brightness.
￭ Press the button cover over entire surface for longer than 4 seconds.
An push-button cannot be used to save the switch-on brightness.
Delete switch-on brightness, only in combination with dimming insert
￭ Press the button cover briefly: Light switches on at the saved switch-on brightness.
￭ Press the button cover over the entire surface for longer than 4 seconds: Switch-on
brightness is deleted. Switching on takes place at the last brightness value set.
A push-button cannot be used to delete the switch-on brightness.
6 Information for electrically skilled persons
DANGER!
Mortal danger of electric shock.
Disconnect the device. Cover up live parts.
Detection field and range
The device has a detection field of 360°. The diameter of the detection field depends on the in-
stallation height and the direction of motion of persons in the detection field. The detection field
becomes larger the greater the installation height, while the detection density and sensitivity are
reduced at the same time.
4 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Figure2: Detection range depending on the direction of movement
Diameter of detection field for direction of movement
Installation height 1: 2: 3: 4:
2.20 m 14.50 m 11.50 m 8.00 m 6.00 m
2.50 m 16.50 m 13.00 m 10.00 m 7.00 m
3.00 m 20.00 m 16.00 m 12.00 m 8.00 m
3.50 m 23.00 m 18.50 m 14.00 m 9.00 m
4.00 m 26.00 m 17.00 m 14.50 m *) – *)
5.00 m 28.00 m 18.00 m 15.00 m *) – *)
6.00 m 29.00 m 19.00 m – *) – *)
1: Range for tangential movement on the ground
2: Range for radial movement on the ground
3: Range for typical movements at desks, e.g. torso movement
4: Range of fine detection at desks, e.g. mouse movements
*) When used as a presence detector: Installation height should not be more than 3.5
m, otherwise fine detection is not possible.
Selecting installation location
For use as a presence detector, the device is installed, for example, above a workplace and
monitors the surface below it. For use as a motion detector, the device is installed, for example,
in the hallway.
￭ Select a vibration-free installation location. Vibrations can lead to unwanted switching.
￭ Avoid interference sources in the detection area. Interference sources can trigger the mo-
tion detector, e.g. heat sources such as heating units, outlets from ventilation openings or
air conditioners, copiers, printers, coffee machines, draughty doorways, animals etc.
The detection field can be limited in order to minimise the influence of interference
sources. For this, use the push-on cover (see Limiting the detection field using the push-
on cover) or switch off individual sensors (see Configuring device settings).
Aligning cover
The device has three independent sensors for motion detection. The arrangement of the areas
A, B and C is clearly evident under the decor ring (Figure 4).
5 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Figure3: Detection field: areas A, B and C; installation height 2.20 m
Figure4: Arrangement of the areas A, B and C
￭ Pay attention to correct alignment when mounting the appliance box and flush-mounted
insert.
￭ Align the cover so that the brightness sensor is on the side away from the windows. This
reduces the effects of scattered light.
Fitting the cover
￭ Connect flush-mounted insert properly and mount in accordance with the desired orienta-
tion of the cover (see instructions for flush-mounted insert).
￭ Fit the cover on the flush-mounted insert
￭ Switch on mains voltage.
If the red status LED flashes three times at repeated intervals, the cover was previously
connected to another insert. If the cover is to remain on the insert, press the Bluetooth
button (4) for longer than 4 seconds.
6 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Limiting the detection field using the push-on cover
The push-on cover can be used to limit the detection field, e.g. in order to mask out interference
sources.
Figure5: Push-on cover
Size Range on the ground (mounting height 3 m)
Complete push-on cover Ø approx. 4.5 m
Area I cut out Ø approx. 7.5 m
Areas I + II cut out Ø approx. 12 m
without push-on cover Ø approx. 20 m
￭ Pull off push-on cover.
￭ Using scissors, cut out push-on cover along the marked lines as required.
￭ Push on push-on cover.
Alternatively, the detection field can also be limited via the app by reducing the sensitivity
or switching off individual sensors.
Expanding the detection field
To expand the detection field, connect a 3-wire extension with presence or motion detector
cover. The main device also evaluates signals of the extension and, if necessary, switches the
lighting on.
Configuring device settings
Settings are configured via the app
Default settings
Function Setting
Operating mode Motion detector
Operating mode Automatic operation
7 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Function Setting
Sensitivity of sensors A-C 100 %
Detection angle 360°, sensors A-C active
Brightness threshold 10lux
Run-on time 2 minutes
Supplementary function switched-off
Checking detection field
Any motions detected are displayed in the app and by the red LED. The lighting is switched on
for approx. 1 second. If the light is not to be switched dependent on motion, the Continuous ON
or Continuous OFF function should also be activated.
3-wire extension: detected motions are sent to the main device. This switches according
to its settings.
￭ Activate the walking test via the app and pace off the detection field. The function is auto-
matically terminated after approx 5 minutes.
Restoring the device to factory settings
After resetting the device to the default setting, it has to be removed from the app. On iOS
equipment, the device also has to be removed from the list of paired Bluetooth devices
(Settings/Bluetooth). Otherwise, re-pairing will not be possible.
￭ Briefly disconnect the device from the mains voltage.
Red LED lights up, self-test runs.
￭ Within 1 minute after switching on the mains voltage, press the Bluetooth Ʃ button for
longer than 20 seconds.
At the conclusion of the self-test or after 4 seconds, the blue LED flashes slowly. Coupling
mode is active; keep the Bluetooth Ʃ button pressed. After approx. 20 seconds, the blue
LED goes out and the red LED flashes quickly.
￭ Within 10 seconds, release the Bluetooth Ʃ button and press briefly once again.
The red LED flashes more slowly, device is reset to the factory settings and restarts.
7 Technical data
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
Dimensions Ø×H 103 × 66 mm
Installation height 3 m
Detection area Ø approx. 20 m (installation height 3m)
Detection angle 360 °
Sensitivity 0, 25, 50, 75, 100%
Brightness threshold
Motion detector operation approx. 5 ... 500lx (and day operation)
Presence detector operation approx. 5 ... 1000lx (and day operation)
Short time operation
pulse duration approx. 0.5 s
pulse stop approx. 3 s
Bluetooth
Radio frequency 2.402 ... 2.480 GHz
Transmission capacity max. 2.5 mW, Class 2
8 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Transmitting range typ. 10 m
8 Parameter list
Adjustable parameter list via app
Depending on the insert, the following parameters can be changed with the app.
Settings for switch and dimming inserts
Parameters Setting options, default set-
ting
Explanation
Operating mode Motion detector operation
Presence detector opera-
tion
Default setting: motion de-
tector operation
Setting whether the device operates as a mo-
tion detector or presence detector.
Operating mode Automatic mode
Timer OFF
Timer ON
Continuous OFF, Continu-
ous ON
Default setting: automatic
mode
Automatic: The load is switched depending on
motion and brightness.
Continuous OFF or ON: The load is perman-
ently switched off or on.
Timer OFF or ON: The load is switched off or
on for the specified time. Afterwards, the
device is in automatic mode again.
Setting timer ON 0.5 - 5 hours
Default setting: 2 h
Time for which the load remains switched on
when the "Timer ON" function is activated.
Setting timer OFF 0.5 - 5 hours
Default setting: 2 h
Time for which the load remains switched off
when the "Timer OFF" function is activated.
Run-on time 10 s ... 60 min
Default setting: 2 min
The load remains switched on for this time,
even if no more motion is detected or the am-
bient light is bright enough.
Dynamic self-
learning run-on
time
On, Off
Default setting: Off
Dynamic self-learning run-on time On:
The device automatically determines a run-on
time within specified limits and dynamically
from detected motion. In so doing, the run-on
time is increased if presence continues or de-
creased if absence is detected. The maximum
run-on time is the set run-on time. The
shortest run-on time is 10 seconds. For run-on
times times from 5 minutes, the brief presence
detection function is also active.
Brightness
threshold
Motion detector:
5… 500 lx
Presence detector: 5…
1000 lx and day operation
Default setting: 10 lx
The load is switched on if the brightness value
falls below this value and if motion is detected.
9 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Parameters Setting options, default set-
ting
Explanation
Using the current
brightness
The current brightness can
be stored in a range of 5 to
500 lx or 1000 lx.
Sets the brightness threshold parameter in the
app to the current brightness.
Sensor sensitivity 0, 25, 50, 75, 100 %
Default setting: 100%
Individually adjust the sensitivity in 5 steps for
each sensor A–C.
To restrict the detection field, switch off indi-
vidual sensors. To do this, set the sensitivity to
0 %.
Reduced basic
sensitivity
On, Off
Default setting: Off
Reduced basic sensitivity On:
Reduced basic sensitivity for use in environ-
ments with interference sources.
Presence simula-
tion
On, Off
Default setting: Off
The function can only be activated after more
than 24 hours of time was saved. In automatic
mode, the times at which the lighting was
switched on are continuously saved. A max-
imum of 60 switching operations are saved
over a period of 24 hours. If more switching
operations take place, the oldest ones are
overwritten respectively. If the presence simu-
lation is activated, the lighting is switched on
at the saved times depending on the bright-
ness. Switch-off takes place after the run-on
time has elapsed. Detected motions prolong
the run-on time or the light is switched on de-
pending on brightness. Times are not saved.
The dynamic run-on time is not taken into ac-
count.
Activating the day
operation
On, Off
Default setting: Off
In the setting day operation the device oper-
ates independently of the brightness.
Activating the
walking test
On, Off
Default setting: Off
Function for checking the detection field. The
function automatically terminates after
5 minutes.
Activate alarm
operation
On, Off
Default setting: Off
This function is used to monitor an area for un-
authorised access during absence. If this is
the case, the lighting flashes (1 second on, 1
second off) for the duration of the run-on time.
In addition, a message is sent via the
Bluetooth interface. When motions are detec-
ted, the run-on time is restarted.
Time change On, Off
Default setting: On
Activates automatic summer/wintertime
changeover
Settings only for switch inserts
Parameters Setting options,
default setting
Explanation
Switch-off pre-
warning
On, Off
Default setting:
Off
If the switch-off pre-warning is activated, the light is not
switched off immediately after the run-on time has
elapsed. Triple flashing at an interval of 10 seconds
shows that the light will be switched off soon. The run-
10 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Parameters Setting options,
default setting
Explanation
on time is thereby prolonged by approx. 30 seconds. If
motion is detected during the switch-off pre-warning,
then the run-on time is restarted and the light remains
on.
Pulse operation On, Off
Default setting:
Off
If motion occurs, then a short pulse of approx. 0.5
seconds is triggered depending on the brightness. The
pulse is repeated approx. every 3 seconds as long as
motions are detected.
Delay output 2
Only for 2-gang
switch insert
Activating switch-
on delay
On, Off
Switch-on delay
0 s ... 60 min
Switch-off delay
0 s ... 60 min
Default setting:
Activating the
switch-on delay
ON, switch-on
delay 2 minutes,
switch-on delay
5 minutes
Activating the switch-on delay:
Activating or deactivating the switch-on delay for output
2
Switch-on delay:
Time to switch on output 2 with a delay when the
switch-on delay is activated.
Switch-off delay:
Time to switch off output 2 with a delay.
Settings only for dimming inserts
Parameters Setting options,
default setting
Explanation
Switch-off pre-
warning
On, Off
Default setting:
Off
If the switch-off pre-warning is activated, the light is not
switched off immediately after the run-on time has
elapsed. The light is first dimmed to minimum bright-
ness within 30 seconds. The run-on time is thereby pro-
longed by approx. 30 seconds. If motion is detected dur-
ing the switch-off pre-warning, then the run-on time is
restarted and the light switches back to the switch-on
brightness.
Switch-on bright-
ness
5 ... 100 %
Default setting:
100%
The light is switched on to a stored brightness.
Maximum dim-
ming value
1 ... 100%
Default setting:
100%
Specifies the maximum settable brightness.
Minimum dim-
ming value
1 ... 67%
Default setting:
100%
Specifies the minimum settable brightness.
Night light/basic
brightness
Do not use func-
tion
Use basic bright-
ness
Use night light
Basic brightness:
If the function is activated, the light is switched to the
switch-on brightness when motion is detected. After the
run-on time has elapsed, the light is not dimmed off but
is dimmed to a defined brightness value.
11 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Parameters Setting options,
default setting
Explanation
Default setting:
Do not use func-
tion
Night light:
When the function is activated, the light is not switched
on to the switch-on brightness but to a defined bright-
ness value when motion is detected.
Adjusting basic
brightness
5 ... 100%
Default setting:
20%
Determines the brightness of the basic brightness func-
tion.
Setting the night
light
5 ... 100%
Default setting:
20%
Determines the brightness of the night light function.
Activating the
constant light
regulation
On, Off
Default setting:
Off
The motion detector determines the brightness value
from artificial light and daylight. This value is kept con-
stant at the set brightness level.
Setting the bright-
ness value
5 ... 1000 lx
Default setting:
600 lx
Value at which the light is kept constant.
Using the current
brightness
Measures the
current bright-
ness value.
Applies the currently measured brightness as the bright-
ness value for the constant light regulation.
9 Troubleshooting
Device does not switch on
Cause 1: The ambient brightness is greater than the adjusted brightness threshold.
Set the brightness value with the app.
Cause 2: Device does not detect any motions.
Increase sensitivity with the app.
Switch on all sensors with the app.
Cause 3: Timer OFF or Continuous OFF is activated.
Activate the automatic mode with the app.
Device switches on without motions
Cause 1: Presence simulation is activated. Device switches at saved times.
Switch off the presence simulation with the app.
Cause 2: Interference sources in the detection area.
Remove interference sources if possible.
Reduce sensitivity with the app.
Limit the detection field with the app.
Device switches off despite motion
Cause 1: The device does not detect any motion.
Increase sensitivity with the app.
Cause 2: Detection area is limited because a sensor was switched off.
Switch on all sensors with the app.
12 / 13
82599322 24.10.2019

System 3000
Presence and motion detector 360° top unit BT
Cause 3: Detection area is limited by push-on cover.
Check the push-on cover.
Device does not switch off
Cause 1: Interference sources in the detection field, device detects motions constantly.
Remove interference sources if possible.
Reduce sensitivity with the app.
Limit the detection field.
Cause 2: Timer ON or Continuous ON is activated.
Activate the automatic mode with the app.
Device does not react to operation with mobile end device, the blue LED does not light.
Cause 1: The mobile end device is not coupled with the device.
Couple the devices.
Cause 2: The Bluetooth interface on the mobile end device is not switched on.
Switch on the Bluetooth interface.
10 Conformity
Gira Giersiepen GmbH & Co. KG hereby declares that the radio system type art. no. 5377 02
meets the directive 2014/53/EU. You can find the full article number on the device. The com-
plete text of the EU Declaration of Conformity is available under the Internet address:
www.gira.de/konformitaet
11 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
Please submit or send faulty devices postage paid together with an error description to your re-
sponsible salesperson (specialist trade/installation company/electrical specialist trade). They will
forward the devices to the Gira Service Center.
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel [phone] - 602-0
Fax [phone] - 602-191
www.gira.de
[email protected]
13 / 13
82599322 24.10.2019