Gira System 3000 User manual

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Motion detector top unit 1.10 m Komfort BT
Order no.: 5374 ..
Motion detector top unit 2.20 m Komfort BT
Order no.: 5376 ..
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. Always disconnect before carrying out work on the device or load. In
so doing, take all the circuit breakers into account, which support dangerous voltages to the
device and or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage. The load
is not electrically isolated from the mains even when the device is switched off.
Do not press on the sensor window. Device can be damaged.
The device is not suitable for use as a burglar alarm or other alarm.
This manual is an integral part of the product, and must remain with the end customer.
2 Device components
Figure1: Motion detector cover 1.10m
1 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Figure2: Motion detector cover 2.20m
(1) FMinsert
(2) Cover frame
(3) Motion detector cover
(4) Sensor window and status LED
(5) Push-button OFF/AUTO ON/AUTO
(6) Button OFF/AUTO
(7) Button ON/AUTO
Status LED
Red LED lights up Self-test
Red LED flashes 3 s on / 3 s off Alarm function active
Red LED flashes 0.5 s on / 0.5 s off Alarm was triggered
Red LED flashes three times followed by a 1 s
pause
Cover was previously connected to another in-
sert
Yellow LED lights up "Continuous off" or "Timer off" function active
Yellow LED flashes Presence simulation active
Green LED lights up "Continuous on" or "Timer on" function active
Blue LED lights up Device is coupled with a mobile end device
and active app
Blue LED flashes 0.5 s on / 0.5 s off Bluetooth coupling mode active
Blue LED flashes quickly Device update is being performed
3 Intended use
– Automatic switching of lighting depending on the heat motion and ambient brightness
– Operation with flush-mounted insert for dimming or switching or 3-wire extension
– Wall installation on flush-mounted insert
– Operation and programming with mobile end device (smartphone or tablet) via Bluetooth
with app
2 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Automatic operation
The device detects heat motions of people, animals and objects.
– The light is switched on if a person enters the detection field and the brightness threshold
is below the set brightness threshold.
– The run-on time restarts with each detected motion.
– The light is switched off if:
no more movement is detected in the detection field and the run-on time has elapsed or
the ambient light is too bright and the run-on time has elapsed.
To avoid any switch-on caused by a cooling lamp, no movement signals are evaluated for a
brief lockout time after switching off. The motion detector adjusts itself to the ambient conditions
to keep the time as short as possible.
Behaviour after a mains voltage failure
After mains voltage return, the device performs a self-test for a maximum of 20 seconds. After
the self-test has been completed, the device is ready for operation.
If the red status LED flashes three times at repeated intervals, the cover was previously
connected to another insert. To enable the function again, either place the cover onto the
respective insert or press the button (5) for more than 4 seconds to the OFF position for
motion detector cover 1.10m, or the OFF button (4) for more than 4 seconds for motion
detector cover 2.20m.
The following applies during the self-test:
– The red status LED is illuminated.
– The load is switched off.
– Movements are not detected.
– The device can be operated via extensions.
4 Product characteristics
Functions directly on the cover
– Extension of the detection field in combination with 3-wire extension
– Continuous on, Continuous off
– Operation with 2-wire or 3-wire extension, rotary extension or push-button, Bluetooth wall
transmitter or push-button
– Resetting to factory setting
Motion detector cover 1.10m
– Cover panel for limiting the detection field
Functions via app
– Setting the brightness threshold
– Adjusting the sensitivity of the PIR sensors
– Setting the run-on time
– Continuous on, Continuous off
– On or off for 0.5 - 5 hours
– Switch-off warning
– Dynamic run-on time
– Presence simulation
– Alarm function
– Call function enables a person to attract attention if required
– Time switch function enables functions to be switched on or off automatically
– Operating lock
– Reduced basic sensitivity
– Automatic summer/winter time changeover
– Test operation
3 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
In combination with a switch insert
– Short time operation
In combination with a dimming insert / DALI Power control unit
– Switching on with the last set brightness / colour temperature or saved switch-on bright-
ness/colour temperature
– Adjusting the minimum brightness
– Adjusting the maximum brightness
– Basic light function
– Night light function
– Setting the minimum colour temperature
– Setting the maximum colour temperature
– Setting the switch-on colour temperature
Colour temperature only in combination with a DALI Power control unit
5 Commissioning
Install app on a mobile end device
Requirement for operation via app is a mobile end device with Bluetooth interface, running the
Android operating system or iOS.
￭ Download and install the Gira System 3000 app from the iTunes App Store (iOS) or the
Google Play Store (Android).
Couple mobile end device via Bluetooth
Precondition: insert and cover must be ready for operation. The mobile end device is located
close to the cover.
￭ Activate coupling mode for motion detector cover 1.10m: Push button (5) to the ON/
AUTO position for more than 4 seconds.
￭ Activate coupling mode for motion detector cover 2.20m: Press the ON/AUTO button (7)
for more than 4 seconds.
The blue LED flashes. The coupling mode is active for 1 minute.
￭ Start the Gira System 3000 app and search for the device to be coupled.
Cover is coupled with the end device and shown in the app.
The coupling mode is automatically exited after successful coupling. The blue LED lights
up to confirm an active connection.
A maximum of 8 mobile end devices can be coupled with a cover. When coupling the 9th
device, the oldest device will be deleted.
6 Operation
The app is used for the configuration and operation of the device. Some basic functions can
also be operated on the cover or via connected extensions.
Operation on the cover
With the push-button or the two buttons you can switch between automatic operation, continu-
ous on and continuous off.
￭ Motion detector cover 1.10m: Move the push-button (5) briefly to position ON or OFF.
￭ Motion detector cover 2.20m: Press the button ON (7) or OFF (6).
Continuous on function green LED is illuminated or continuous off function yellow LED is
illuminated.
In order to switch on automatic operation again, repeat the action above. Green or yellow
LED goes out.
4 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Operation using 2-wire or 3-wire extension with push-button cover, Bluetooth wall transmitter or
push-button
Multiple extensions can be combined with each other. All operations described here are also
possible via the app. Operation with the rotary extension is described in the rotary extension in-
structions.
Switching on light for the duration of the run-on time
￭ Press briefly.
Pressing again briefly in the switched-on state restarts the run-on time. In combination
with a dimming insert or DALI Power control unit, the brightness switches back to the
switch-on brightness.
Short-time operation: When pressed, pulses are generated approx. every 3 seconds for
1 minute. Exception for 3-wire extension: only one pulse is generated.
Adjusting the brightness
￭ Press longer.
In the case of a push-button, the dimming direction is changed with each new long actu-
ation.
Setting the colour temperature
Only with 2-wire extension, Bluetooth wall transmitter and push-button.
Only with DALI Power control unit.
￭ In the switched-on state, press twice within 0.4 seconds (double-click). The light switches
off and on again.
The device switches to "Setting the colour temperature" mode.
￭ Long press to set the colour temperature.
In the case of a push-button, the setting direction is changed with each new long actu-
ation.
After a further double click, the device switches back to normal operation. This is signalled
by switching off briefly and back on again. The device also switches to normal operation
after 1 minute without operation.
Saving the switch-on brightness / colour temperature
Only with 2-wire extension.
Colour temperature only with a DALI Power control unit.
￭ Adjust the brightness.
￭ Set the colour temperature.
￭ Press the push-button cover over entire surface for longer than 4 seconds.
Switch-on brightness and colour temperature are saved. The switch-on behaviour
changes to "Switch on with the saved brightness and colour temperature".
Deleting the switch-on brightness / colour temperature
Only with 2-wire extension.
Colour temperature only with a DALI Power control unit.
￭ Press briefly: Light switches on with the saved switch-on brightness and colour temperat-
ure.
￭ Without changing the brightness, press push-button cover over entire surface for longer
than 4 seconds. .
Switch-on brightness and colour temperature are deleted. The switch-on behaviour
changes to "Switch on with the most recently set brightness and colour temperature".
5 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Call function
The function enables a person to attract attention if required. A call can be triggered via a 2-wire
extension, Bluetooth wall transmitter or push-button.
Precondition: The call function has been activated via the app.
￭ Press the button of the extension.
Light flashes (1 second on, 1 second off) until the call is acknowledged by actuating the
device.
7 Information for electrically skilled persons
DANGER!
Mortal danger of electric shock.
Disconnect the device. Cover up live parts.
Motion detection
The detection of heat sources through a motion detector and thus the extent of the detection
field is influenced by the following criteria:
Geometry of the detection field, assembly height and set sensitivity (Figure 3) up to (Figure 10)
Direction of movement : Passing the motion detector tangentially results in a heat signal which
can be evaluated well. If movement is radial to the sensor, the heat signal is smaller and thus
harder to evaluate, resulting in a smaller range.
The following specifications on the extent of the detection field are general guide values.
Discrepancies can occur depending on the installation environment and the intensity of
the heat motion.
Motion detector cover 1.10 m detection field and range
Figure3: Motion detector cover 1.10 m detection field and installation height
6 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Figure4: Range with tangential direction of motion for motion detector cover 1.10 m
1 25% sensitivity
2 50% sensitivity
3 75% sensitivity
4 100% sensitivity
Figure5: Range with radial direction of motion for motion detector cover 1.10 m
1 25% sensitivity
2 50% sensitivity
3 75% sensitivity
4 100% sensitivity
7 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Motion detector cover 2.20 m detection field and range
Figure6: Motion detector cover 2.20 m detection field and installation height
Figure7: Range with tangential direction of motion for motion detector cover 2.20 m, mounting
height 2.20 m
1 25% sensitivity
2 50% sensitivity
3 75% sensitivity
4 100% sensitivity
Figure8: Range with radial direction of motion for motion detector cover 2.20 m, mounting
height 2.20 m
1 25% sensitivity
2 50% sensitivity
8 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
3 75% sensitivity
4 100% sensitivity
Figure9: Range with tangential direction of motion for motion detector cover 2.20 m, mounting
height 1.10 m
1 25% sensitivity
2 50% sensitivity
3 75% sensitivity
4 100% sensitivity
Figure10: Range with radial direction of motion for motion detector cover 2.20 m, mounting
height 1.10 m
1 25% sensitivity
2 50% sensitivity
3 75% sensitivity
4 100% sensitivity
Selecting installation location
￭ Select a vibration-free installation location. Vibrations can lead to unwanted switching.
￭ To achieve optimum range, choose an installation location that is tangential to the direc-
tion of motion.
￭ Avoid heat sources in the detection field such as heating units, outlets of ventilation sys-
tems or air conditioners, copiers, printers, coffee machines, draughty doorways, animals
etc.
9 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Mounting the cover
￭ Connecting and mounting the FM insert properly (see flush-mounted insert instructions).
￭ Fit the cover with frame on the flush-mounted insert.
Expanding the detection field
To expand the detection field, connect a 3-wire extension with presence or motion detector
cover. The main device also evaluates signals of the extension and, if necessary, switches the
lighting on.
Limiting the detection field
The detection field can also be limited by reducing the sensitivity or switching off a sensor.
Alternatively, the detection field for motion detector cover 1.10m can be limited with cover panel
(Figure 11) and (Figure 12).
Figure11: Limiting detection field for motion detector cover 1.10m
Figure12: Mounting cover panel 90°
Configuring device settings
Settings are configured via the app
Default settings
Function Setting
Operating function Automatic operation
Sensitivity 100%
Detection angle 180°
Brightness threshold 10lux
Run-on time 2 minutes
Supplementary function switched-off
Checking detection field
Any motions detected are displayed in the app and by the red LED. The lighting is switched on
for approx. 1 second. If the light is not switched by motion, the Continuous on or Continuous off
functions can also be activated.
10 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
3-wire extension: detected motions are sent to the main device. This switches according
to its settings.
￭ Activate the walking test via the app and pace off the detection field. The function is auto-
matically terminated after approx 5 minutes.
Restoring the device to factory settings
After resetting the device to the default setting, it has to be removed from the app. On iOS
equipment, the device also has to be removed from the list of paired Bluetooth devices
(Settings/Bluetooth). Otherwise, re-pairing will not be possible.
Motion detector cover 1.10m
￭ Briefly disconnect the device from the mains voltage.
Red LED lights up, self-test runs.
￭ Within 1 minute after switching on the mains voltage, move the push-button (5) to position
OFF/AUTO and hold for more than 20 seconds.
After approx. 20 seconds, the red LED flashes quickly.
￭ Within 10 seconds, release the button and move briefly to position OFF/AUTO once
again.
The red LED flashes more slowly, device is reset to the factory settings and restarts.
Motion detector cover 2.20m
￭ Briefly disconnect the device from the mains voltage.
Red LED lights up, self-test runs.
￭ Within 1 minute after switching on the mains voltage, press the OFF button (6) for more
than 20 seconds.
After approx. 20 seconds, the red LED flashes quickly.
￭ Within 10 seconds, release the button and actuate it briefly once again.
The red LED flashes more slowly, device is reset to the factory settings and restarts.
8 Technical data
Ambient temperature -20 ... +45 °C
Storage/transport temperature -25 ... +70 °C
Degree of protection
System 55, Gira E22, Flächenschalter (F100) IP20
Gira TX_44 IP44
Brightness setting approx. 5 ... 500 lx and day operation
Sensitivity 0, 25, 50, 75, 100%
Run-on time approx. 10 s ... 60 min
Installation height
Order no. 5374 .. 1.10 m / 2.20 m 1.10 m
Order no. 5376 .. 1.10 m 1.10 m / 2.20 m
Detection angle 180 °
Radio frequency 2.402 ... 2.480 GHz
Transmission capacity max. 2.5 mW, Class 2
Transmitting range typ. 10 m
9 Parameter list
Adjustable parameters via app
Depending on the insert, the following parameters can be changed with the app.
11 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Settings for switch and dimming inserts
Parameters Setting options, default set-
ting
Explanation
EnOcean switch MAC address
Name
Single rocker
Left rocker
Right rocker
The Bluetooth wall transmitter must be con-
nected to the device in order to be able to op-
erate it. Enter the MAC address of the
Bluetooth wall transmitter here, select the
device button to be used for operation and as-
sign a name. Up to 8 Bluetooth wall transmit-
ters can be connected to the device.
Operating mode Automatic mode
Timer OFF
Timer ON
Continuous OFF
Continuous ON
Default setting: automatic
mode
Automatic: The load is switched depending on
motion and brightness.
Continuous OFF or ON: The load is perman-
ently switched off or on.
Timer OFF or ON: The load is switched off or
on for the specified time. Afterwards, the
device is in automatic mode again.
Setting timer OFF 0.5 - 5 hours
Default setting: 2 h
Time for which the load remains switched off
when the "Timer OFF" function is activated.
Setting timer ON 0.5 - 5 hours
Default setting: 2 h
Time for which the load remains switched on
when the "Timer ON" function is activated.
Run-on time 10 s ... 60 min
Default setting: 2 min
The load remains switched on for this time,
even if no more motion is detected or the am-
bient light is bright enough.
Dynamic self-
learning run-on
time
On, Off
Default setting: Off
Dynamic self-learning run-on time On:
The device automatically determines a run-on
time within specified limits and dynamically
from detected motion. In so doing, the run-on
time is increased if presence continues or de-
creased if absence is detected. The maximum
run-on time is the set run-on time. The
shortest run-on time is 10 seconds. For run-on
times from 5 minutes, the brief presence de-
tection function is also active.
Brightness
threshold
Motion detector: 5… 500 lx
Default setting: 10 lx
The load is switched on if the brightness value
falls below this value and if motion is detected.
Using the current
brightness
The current brightness can
be stored in a range of 5 to
500 lx.
Sets the brightness threshold parameter in the
app to the current brightness.
Sensor sensitivity 0, 25, 50, 75, 100%
Default setting: 100%
Individually adjust the sensitivity in 5 steps for
the left and the right sensor.
To restrict the detection field, switch off indi-
vidual sensors. To do this, set the sensitivity to
0%.
Reduced basic
sensitivity
On, Off
Default setting: Off
Reduced basic sensitivity On:
Reduced basic sensitivity for use in environ-
ments with interference sources.
12 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Parameters Setting options, default set-
ting
Explanation
Presence simula-
tion
On, Off
Default setting: Off
The function can only be activated after more
than 24 hours of time was saved. In automatic
mode, the times at which the lighting was
switched on are continuously saved. A max-
imum of 60 switching operations are saved
over a period of 24 hours. If more switching
operations take place, the oldest ones are
overwritten respectively. If the presence simu-
lation is activated, the lighting is switched on
at the saved times depending on the bright-
ness. Switch-off takes place after the run-on
time has elapsed. Detected motions prolong
the run-on time or the light is switched on de-
pending on brightness. Times are not saved.
The dynamic run-on time is not taken into ac-
count.
Activate day op-
eration
On, Off
Default setting: Off
In the setting day operation the device oper-
ates independently of the brightness.
Activate walking
test
On, Off
Default setting: Off
Function for checking the detection field. The
function automatically terminates after
5 minutes.
Activate alarm
operation
On, Off
Default setting: Off
This function is used to monitor an area for un-
authorised access during absence. If this is
the case, the lighting flashes (1 second on, 1
second off) for the duration of the run-on time.
When motions are detected, the run-on time is
restarted.
Activate call func-
tion
On, Off
Default setting: Off
The function enables a person to attract atten-
tion if required. If the function is activated, a
call can be triggered via a 2-wire extension,
Bluetooth wall transmitter or push-button. If a
call has been triggered, the lighting flashes (1
second on, 1 second off) until the call is ac-
knowledged by actuating the device. A
triggered call overrides all functions of the
device. The functions continue running in the
background so that the device switches to the
respective current state after acknowledge-
ment.
Deactivate local
operation
On, Off
Default setting: Off
The device cannot be operated on location if
the local operating lock is active. For use in
public areas.
Time change On, Off
Default setting: On
Activates automatic summer/wintertime
changeover.
Timers 16 switch points
Default setting: none
With this function it is possible to automatically
switch on functions such as night light / basic
brightness or presence simulation for a
defined period of time. A weekly timer is avail-
able for this purpose. The timer updates itself
with every Bluetooth connection to a mobile
13 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Parameters Setting options, default set-
ting
Explanation
end device. One function can be switched on
or off per switch point. A time and one or more
weekdays are assigned to each switch point.
Settings only for switch inserts
Parameters Setting options,
default setting
Explanation
Activating the
switch-off pre-
warning
On, Off
Default setting:
Off
If the switch-off pre-warning is activated, the light is not
switched off immediately after the run-on time has
elapsed. Triple flashing at an interval of 10 seconds
shows that the light will be switched off soon. The run-
on time is thereby prolonged by approx. 30 seconds. If
motion is detected during the switch-off pre-warning,
then the run-on time is restarted and the light remains
on.
Pulse operation On, Off
Default setting:
Off
If motion occurs, then a short pulse of approx. 0.5
seconds is triggered depending on the brightness. The
pulse is repeated approx. every 3 seconds as long as
motions are detected.
Delay output 2
Only for 2-gang
switch insert
Activating switch-
on delay
On, Off
Switch-on delay
0 s ... 60 min
Switch-off delay
0 s ... 60 min
Default setting:
Activating the
switch-on delay
ON, switch-on
delay 2 minutes,
switch-on delay
5 minutes
Activating the switch-on delay:
Activating or deactivating the switch-on delay for output
2
Switch-on delay:
Time to switch on output 2 with a delay when the
switch-on delay is activated.
Switch-off delay:
Time to switch off output 2 with a delay.
Settings only for dimming inserts, DALI Power control unit
Parameters Setting options,
default setting
Explanation
Activating the
switch-off pre-
warning
On, Off
Default setting:
Off
If the switch-off pre-warning is activated, the light is not
switched off immediately after the run-on time has
elapsed. The light is first dimmed to minimum bright-
ness within 30 seconds. The run-on time is thereby pro-
longed by approx. 30 seconds. If motion is detected dur-
ing the switch-off pre-warning, then the run-on time is
restarted and the light switches back to the switch-on
brightness.
Switch-on bright-
ness
5 ... 100%
Default setting:
100%
The light is switched on to a stored brightness.
14 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Parameters Setting options,
default setting
Explanation
Maximum dim-
ming value
1 ... 100%
Default setting:
100%
Specifies the maximum settable brightness.
Minimum dim-
ming value
1 ... 67%
Default setting:
100%
Specifies the minimum settable brightness.
Night light/basic
brightness
Do not use func-
tion
Use basic bright-
ness
Use night light
Default setting:
Do not use func-
tion
Basic brightness:
If the function is activated, the light is switched to the
switch-on brightness when motion is detected. After the
run-on time has elapsed, the light is not dimmed off but
is dimmed to a defined brightness value.
Night light:
When the function is activated, the light is not switched
on to the switch-on brightness but to a defined bright-
ness value when motion is detected.
Adjusting basic
brightness
5 ... 100%
Default setting:
20%
Determines the brightness of the basic brightness func-
tion.
Setting the night
light
5 ... 100%
Default setting:
20%
Determines the brightness of the night light function.
Colour temperat-
ure
Only DALI Power
control unit
Minimum colour
temperature
2000 ... 4500 K
Maximum colour
temperature
5000 ... 10000 K
Switch-on colour
temperature
2000 ... 10000 K
Factory setting:
Minimum colour
temperature
2000 K, max-
imum colour tem-
perature 6000 K,
switch-on colour
temperature
2700 K
Minimum colour temperature: Defines the minimum col-
our temperature that can be set.
Maximum colour temperature: Defines the maximum
colour temperature that can be set.
Switch-on colour temperature: The light is switched on
with a saved colour temperature.
10 Troubleshooting
Motion detector does not switch on
Cause 1: The ambient brightness is greater than the adjusted brightness threshold.
Set the brightness threshold via app.
15 / 16
32599722 10865948 13.07.2022

System 3000
Motion detector top unit 1.10 m Komfort BT, Motion detector top unit 2.20 m
Komfort BT
Cause 2: Motion detector does not detect any motions.
Check detection field for any obstacles.
Adjust the sensitivity of the sensors via app.
Motion detector switches on without motion
Cause: Motion detector detects heat motions.
Pay attention to interference sources such as heaters, fans, air-conditioners and cooling
luminaires in the detection field.
Motion detector switches off despite motion
Cause: The ambient light is too bright and the switch-off threshold was exceeded.
Set the brightness threshold via app.
Motion detector does not switch off after the set run-on time has elapsed
Cause: Motion detector detects motions constantly.
Pay attention to interference sources such as heaters, fans and air-conditioners in the de-
tection field.
11 Conformity
Gira Giersiepen GmbH & Co. KG hereby declares that the radio system type art. no. 5374 .. and
5376 .. meets the directive 2014/53/EU. You can find the full article number on the device. The
complete text of the EU Declaration of Conformity is available under the Internet address:
www.gira.de/konformitaet
12 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
Please submit or send faulty devices postage paid together with an error description to your re-
sponsible salesperson (specialist trade/installation company/electrical specialist trade). They will
forward the devices to the Gira Service Center.
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel [phone] - 602-0
Fax [phone] - 602-191
www.gira.de
[email protected]
16 / 16
32599722 10865948 13.07.2022