GIRBAU HS-6008 User manual

Cod. 429704
Rev. 02/0606
Advanced Operation Instructions
for washers
COIN CONTROL
GIRBAU, S.A.
Crta de Manlleu, km. 1
08500 VIC (Barcelona) •SPAIN
Tel. [phone]
Fax [phone]
[email protected]
www.girbau.com
For USA & CANADA:
CONTINENTAL GIRBAU Inc.
2500 State Road 44
WI 54904 Oshkosh •USA
Tel. [phone]
Fax [phone]
[email protected]
www.cont-girbau.com
COIN
Advanced

Cod. 429704
Rev. 02/0606
Model From serial #
High Speed
HS-6008 2.080.884
HS-6013 2.110.200
HS-6017 2.120.320
EH020 1.430.001
EH030 1.460.021
EH040 1.470.060
Medium Speed
MS-610 2.020.001
MS-613 2.030.001
MS-617 2.040.001
MS-623 2.050.001
EM025 1.370.001
EM030 1.380.001
EM040 1.390.001
EM055 1.400.001

Cod. 429704
Rev. 02/0606
3
Index
SAFETY INSTRUCTIONS
INDEX ........................................................................................................................................... 3
1. DESCRIPTION
1.1 Characteristics
1.2 Expected use of the washer
2. OPERATION INSTRUCTIONS
2.1 Control panel
2.2 Loading the washing machine
2.3 Using the dispenser
2.4 Starting a program
2.5 Program application and parameters
2.6 Stop modes
2.7 Unbalance control
3. MODIFICATION MODE .................................... ....................................................................... 4
3.1 Access to MODIFICATION mode .......................................................................................... 4
3.2. Modification of program contents. Pro menu ......................................................................... 4
3.2.1 Master program ........................................................................................................... 5
3.2.2 Program contents. CE configuration. All models ......................................................... 6
3.2.3 Program contents. USA configuration. EH020, EM025. SP-0 models.......................... 6
3.2.4 Program contents. USA configuration. EH020, EM025. SP-1 models ......................... 7
3.2.5 Program contents. USA configuration. Other models ................................................... 7
3.2.6 Phases definition............................................................................................................ 8
3.2.7 Definition of programmable functions and values for each phase................................. 9
3.2.8 Modification of a program ........................................................................................... 10
3.3. Program price. Single price for each program. CASH Menu
3.3.1. Program price programming / modification
3.4. Operation mode with program accelerator. DEMO menu..................................................... 11
3.4.1. Execution of a program in DEMO mode .................................................................... 11
3.5 Information menu. Info menu ................................................................................................ 12
3.6. Modification of operating parameters. Mod menu ............................................................... 12
3.6.1 Parameters modification .......................................................................................... 12
3.7 Modification of access code to modification mode. Ncod menu .......................................... 15
4. PROGRAMS PRICE ..................................... ..................................................................... 15
4.1 Hour menu ........................................................................................................................... 15
4.1.1 Setting clock time and day of the week ................................................................... 16
4.2 CALE menu .......................................................................................................................... 16
4.2.1 Time programming ..................................................................................................... 16
4.3 CASH menu ......................................................................................................................... 17
4.3.1 Price of each program according to the three rates ................................................... 17
5. TROUBLESHOOTING
5.1 What to do when
5.2 System alarms
6. MAINTENANCE
6.1 Operations described
6.2 Cleaning the washer
6.3 Cleaning the door seal
6.4 Cleaning the electrovalve filters
6.5 Cleaning the dispenser
6.6 Cleaning the drain pump
6.7 Revising the safety mechanisms
6.8 General revision
7. SERVICE REMOVAL
7.1 Dismantling
NOTE
For the contents of SAFETY INSTRUCTIONS, chapters 1. DESCRIPTION, 2. OPERATING INSTRUCTIONS, section
3.3 of chapter 3. MODIFICATION MODE, 5. TROUBLESHOOTING, 6. MAINTENANCE and 7. SERVICE REMOVAL,
see Operation Instructions for COIN CONTROL, supplied with the washer or request it to the manufacturer:
[email protected], (USA/CANADA: [email protected] )

Cod. 429704
Rev. 02/0606
4
Advanced Mode
3. MODIFICATION MODE.
The MODIFICATION mode offers some menus, which allow the modification of programs contents, the price
management of the programs, the modification of operating parameters …
The MODIFICATION mode is made up of eight menus defined in the following chart:
MENU PURPOSE SECTION
Pro Modification of program contents Section 3.2
CASH Programming and/or modifying each program price Section 3.3 Operation
instructions book
DEMO Operation mode with program accelerator Section 3.4
INFO Information menu Section 3.5
Mod Modification of the operating parameters Section 3.6
Ncod Modification of access code Section 3.7
CALE Prices allocation according to hour band Section 4.2 & 4.3
HOUR Adjust the system time Section 4.1
3.1. Access to MODIFICATION mode
Connect the washer and open the door. The display shows door.
Push and hold down 1key until the Cod report appears on the display.
Enter the access code to the menus pressing, without interruption, the sequence of eight keys of the code. In
basic configuration (when the machine is delivered) the access code to MODIFICATION is: 12341234
If the sequence set is correct, the display will show Pro, corresponding to the first menu.
Keys 2and 4allow the selection of the precedent table menus. The menu selected is showed in the display
following its keyword. To enter in it, press the 1key when displaying it.
If wished to skip the MODIFICATION mode, press STOP and machine will return to program execution mode.
The MODIFICATION mode can be also left disconnecting the electric supply of the washing machine.
3.2. Modification of program contents. Pro menu.
In its original configuration, the washing machine has four wash programs with content adapted to a wide
range of usage. However, the content of each program can be modified to be adapted to the specific needs
of different situations.
The modifications will always be carried out starting from a MASTER PROGRAM that understands the
programmable parameters and the maximum and minimum values of certain options.
The master program is composed of six phases. At the start of each phase, a parameter of the value PH-Y /
Ph-N (execute YES phase / execute NO phase) will allow the user to determine if the phase to access
should be executed or, on the contrary, be omitted.
Once the phase is defined as to be executed, proceed to the display and modification (if desired) of the
parameters or values of the phase.

Cod. 429704
Rev. 02/0606
5
Advanced Mode
3.2.1. Master program
EXECUTION LEVEL TEMP. DOSING ROTATION ROTATION
TIME EXTRACT EXTRACT TIME
PHASE Ph L C / F d r rt E Et
1 Y / N 1…3 n.p. 1 1...3 1...6 1...3 n.p. 2...3
2 Y 1…3
0 ... 80
32 ... 176 2 1...3 1...20 1 / 2 n.p. 2
3 Y 1…3 n.p. 0 / 3 1...3 1...6 1...3 n.p. 2...3
4 Y / N 1…3 n.p. n.p. 1...3 1...6 1...3 n.p. 2...3
5 Y / N 1…3 n.p. n.p. 1...3 1...6 1 n.p.
6 Y 1…3 n.p. 0 / 4 1...3 1...6 1...6 n.p. 2...7
Refer to section 3.2.6, 7 and 8 for the definition of functions and programmable values of each phase.